Breadboard ends and router issues
 

I've lost all confidence in my PC 892 router and a 8901 fixed base
permanently attached to my tablesaw insert. The router slips down after
it's locked and in use. I've ruined 2 sets of bread board ends because of
this and the slots in the top had to be cut off.

The screw on the locking cam is adjusted as tight as it will go and still
allow router movement. There's no dust between the pinon and gear or
housing, I clean that out every time I insert a bit. I've adjusted the
router up to the correct height in an attempt to get rid of the
backlash/slippage. It's a fairly new router. I never had this issue with my
old router that I continually removed from the base to use as a handheld.
Maybe I'll go back to that one.

Any suggestions on what more I can do to stop the slip?
Or what other router & base I could get that wouldn't have this problem.
Now I don't want to use it again for for fear of it slipping again and
ruining the top and ends (again).

Breadboard ends and router issues
 

On Sun, 29 Jul 2018 16:00:02 GMT, sawdustmaker
wrote:

I've lost all confidence in my PC 892 router and a 8901 fixed base
permanently attached to my tablesaw insert. The router slips down after
it's locked and in use. I've ruined 2 sets of bread board ends because of
this and the slots in the top had to be cut off.

The screw on the locking cam is adjusted as tight as it will go and still
allow router movement. There's no dust between the pinon and gear or
housing, I clean that out every time I insert a bit. I've adjusted the
router up to the correct height in an attempt to get rid of the
backlash/slippage. It's a fairly new router. I never had this issue with my
old router that I continually removed from the base to use as a handheld.
Maybe I'll go back to that one.

Any suggestions on what more I can do to stop the slip?
Or what other router & base I could get that wouldn't have this problem.
Now I don't want to use it again for for fear of it slipping again and
ruining the top and ends (again).

The big question is "why is it slipping". See if you can make it slip
on the benchtop where you can see what's moving and maybe figure out
why.

Porter Cable makes an accessory for that router for router table
use--Item 75301. Whether it will address this problem I have no idea
but it's about 30 bucks.on Amazon.

Beyond that, look into a proper router lift--JessEm has one for about
180 bucks or if you google "DIY Router Lift" you'll find some ideas of
how to cobble up your own.

Breadboard ends and router issues
 

J. Clarke wrote in
:

On Sun, 29 Jul 2018 16:00:02 GMT, sawdustmaker
wrote:

I've lost all confidence in my PC 892 router and a 8901 fixed base
permanently attached to my tablesaw insert. The router slips down
after it's locked and in use. I've ruined 2 sets of bread board ends
because of this and the slots in the top had to be cut off.

The screw on the locking cam is adjusted as tight as it will go and
still allow router movement. There's no dust between the pinon and
gear or housing, I clean that out every time I insert a bit. I've
adjusted the router up to the correct height in an attempt to get rid
of the backlash/slippage. It's a fairly new router. I never had this
issue with my old router that I continually removed from the base to
use as a handheld. Maybe I'll go back to that one.

Any suggestions on what more I can do to stop the slip?
Or what other router & base I could get that wouldn't have this
problem. Now I don't want to use it again for for fear of it slipping
again and ruining the top and ends (again).

The big question is "why is it slipping". See if you can make it slip
on the benchtop where you can see what's moving and maybe figure out
why.

Porter Cable makes an accessory for that router for router table
use--Item 75301. Whether it will address this problem I have no idea
but it's about 30 bucks.on Amazon.

Beyond that, look into a proper router lift--JessEm has one for about
180 bucks or if you google "DIY Router Lift" you'll find some ideas of
how to cobble up your own.


Yeah -- The combo kit came with that (75301), it's a height adjuster on
the top. I ended up tightening the screw as much as I could and still
have the router adjust and the cam lock. I got acceptable results, not
perfect but acceptable. The moral is to check router bit height a lot to
ensure that the router isn't slipping down.

Breadboard ends and router issues
 

On 7/30/2018 8:02 PM, sawdustmaker wrote:
J. Clarke wrote in
:

On Sun, 29 Jul 2018 16:00:02 GMT, sawdustmaker
wrote:

I've lost all confidence in my PC 892 router and a 8901 fixed base
permanently attached to my tablesaw insert. The router slips down
after it's locked and in use. I've ruined 2 sets of bread board ends
because of this and the slots in the top had to be cut off.

The screw on the locking cam is adjusted as tight as it will go and
still allow router movement. There's no dust between the pinon and
gear or housing, I clean that out every time I insert a bit. I've
adjusted the router up to the correct height in an attempt to get rid
of the backlash/slippage. It's a fairly new router. I never had this
issue with my old router that I continually removed from the base to
use as a handheld. Maybe I'll go back to that one.

Any suggestions on what more I can do to stop the slip?
Or what other router & base I could get that wouldn't have this
problem. Now I don't want to use it again for for fear of it slipping
again and ruining the top and ends (again).

The big question is "why is it slipping". See if you can make it slip
on the benchtop where you can see what's moving and maybe figure out
why.

Porter Cable makes an accessory for that router for router table
use--Item 75301. Whether it will address this problem I have no idea
but it's about 30 bucks.on Amazon.

Beyond that, look into a proper router lift--JessEm has one for about
180 bucks or if you google "DIY Router Lift" you'll find some ideas of
how to cobble up your own.


Yeah -- The combo kit came with that (75301), it's a height adjuster on
the top. I ended up tightening the screw as much as I could and still
have the router adjust and the cam lock. I got acceptable results, not
perfect but acceptable. The moral is to check router bit height a lot to
ensure that the router isn't slipping down.

I once had a similar problem. I bit the bullet, bought a Triton
plunge router, and mounted it as a table router in my table saw
extension. Problem solved. One of these:
https://www.amazon.com/Triton-TRA001..._89%3ATrit on