steam bending plywood
 

was looking at some objects made from steam bended ply

just realized that they had to havve bent that when they glued the plys
together

far as i know ply will come undone if you steam it and not magically
adhere when it cools

bending and gluing plys would get messy and require a special built
jig


it is a nice look though

steam bending plywood
 

On 5/16/2018 11:22 AM, Electric Comet wrote:

was looking at some objects made from steam bended ply

just realized that they had to havve bent that when they glued the plys
together

far as i know ply will come undone if you steam it and not magically
adhere when it cools

bending and gluing plys would get messy and require a special built
jig


it is a nice look though


No steam needed if it is done properly with the correct materials. It
_will_ require an accurate jig/form/fixture to achieve the correct
curvature and unless you are up for making both male/female forms you will
need a vacuum bag setup. Other than making sure that the glue used is
low-creep it is a pretty simple process to put together 5mm sheets of
'wiggle wood' in a way that they will stay that way after the glue dries
and it comes out of the bag.

steam bending plywood
 

On Wed, 16 May 2018 15:06:58 -0400, John McGaw
wrote:

On 5/16/2018 11:22 AM, Electric Comet wrote:

was looking at some objects made from steam bended ply

just realized that they had to havve bent that when they glued the plys
together

far as i know ply will come undone if you steam it and not magically
adhere when it cools

bending and gluing plys would get messy and require a special built
jig


it is a nice look though


No steam needed if it is done properly with the correct materials. It
_will_ require an accurate jig/form/fixture to achieve the correct
curvature and unless you are up for making both male/female forms you will
need a vacuum bag setup. Other than making sure that the glue used is
low-creep it is a pretty simple process to put together 5mm sheets of
'wiggle wood' in a way that they will stay that way after the glue dries
and it comes out of the bag.

Note that this is not new technology. The Romans made their curved
shields of 3 layers of laminated wood.

steam bending plywood
 

On Wednesday, May 16, 2018 at 3:07:07 PM UTC-4, John McGaw wrote:
On 5/16/2018 11:22 AM, Electric Comet wrote:

was looking at some objects made from steam bended ply

just realized that they had to havve bent that when they glued the plys
together

far as i know ply will come undone if you steam it and not magically
adhere when it cools

bending and gluing plys would get messy and require a special built
jig


it is a nice look though


No steam needed if it is done properly with the correct materials. It
_will_ require an accurate jig/form/fixture to achieve the correct
curvature and unless you are up for making both male/female forms you will
need a vacuum bag setup. Other than making sure that the glue used is
low-creep it is a pretty simple process to put together 5mm sheets of
'wiggle wood' in a way that they will stay that way after the glue dries
and it comes out of the bag.

I wonder if they used steam to bend these arches. ;-)

https://i.imgur.com/8VCSsc6.jpg

That's the Arthur A. Smith Covered Bridge, the only Burr truss bridge
in Massachusetts. Originally built in 1869, the arches were added in 1920.
It was completed restored in 2007. It's located in Colrain, MA. That's
SWMBO and my daughter going into the light.

Exterior view:

https://i.imgur.com/QMkPosf.jpg