tools for a Delta 34-444 table saw
 

I recently purchased a Delta 34-444 table saw, but the seller didn't have
the wrenches to change blades. One is an open end and one is a box end.
I've found very few sources for the box end and they all say the open end
is obsolete (?) Any ideas for a source for these wrenches?
Thanks

--

tools for a Delta 34-444 table saw
 

On 7/18/2014 8:44 PM, Jack wrote:
I recently purchased a Delta 34-444 table saw, but the seller didn't have
the wrenches to change blades. One is an open end and one is a box end.
I've found very few sources for the box end and they all say the open end
is obsolete (?) Any ideas for a source for these wrenches?
Thanks


As far as obsolete goes, no they are not obsolete, there may not be
anyone that has them or they may be discontinued but they are not
obsolete. If you going to use two wrenches to tighten and loosen the
arbor nut you have to have an open end for the flange side of the arbor.


Most all of these type wrenches are stamped steel, nothing special other
than the fact that they are narrow.
I would measure the sizes ant buy some cheap Harbor Freight or Northern
Tool wrenches and grind them down in thickness.

tools for a Delta 34-444 table saw
 

On 7/18/2014 9:44 PM, Jack wrote:
I recently purchased a Delta 34-444 table saw, but the seller didn't have
the wrenches to change blades. One is an open end and one is a box end.
I've found very few sources for the box end and they all say the open end
is obsolete (?) Any ideas for a source for these wrenches?
Thanks

If they are common sizes, you can usually pick up a wrench for a dollar
or so at a flea market. You can get your wrenches, have fun and
possibly get some other bargains.

tools for a Delta 34-444 table saw
 

On 7/18/2014 8:44 PM, Jack wrote:
I recently purchased a Delta 34-444 table saw, but the seller didn't have
the wrenches to change blades. One is an open end and one is a box end.
I've found very few sources for the box end and they all say the open end
is obsolete (?) Any ideas for a source for these wrenches?

For the open end one, look for a "bicycle" wrench of the appropriate size.

--
eWoodShop: www.eWoodShop.com
Wood Shop: www.e-WoodShop.net
https://www.google.com/+eWoodShop
https://plus.google.com/+KarlCaillouet/posts
http://www.custommade.com/by/ewoodshop/
KarlCaillouet@ (the obvious)

tools for a Delta 34-444 table saw
 

"Jack" wrote in message
roups.com...

I recently purchased a Delta 34-444 table saw, but the seller didn't have
the wrenches to change blades. One is an open end and one is a box end.
I've found very few sources for the box end and they all say the open end
is obsolete (?) Any ideas for a source for these wrenches?
Thanks

What are the distances across the flats?

Tom

tools for a Delta 34-444 table saw
 

replying to Leon , Jack wrote:



lcb11211 wrote:

As far as obsolete goes, no they are not obsolete, there may not be
anyone that has them or they may be discontinued but they are not
obsolete. If you going to use two wrenches to tighten and loosen the
arbor nut you have to have an open end for the flange side of the arbor.
Most all of these type wrenches are stamped steel, nothing special other
than the fact that they are narrow.
I would measure the sizes ant buy some cheap Harbor Freight or Northern
Tool wrenches and grind them down in thickness.




As far as all of the Delta parts lists, they consider one of the wrenches
"obsolete" (in their words). Thanks for all of the replies. The arbor
nut is 7/8" so a 7/8 box end works great. The person that replied with
one of the best ideas for the arbor shaft is the bicycle wrench, although
I found that the thin wrench I got with my old Craftsman saw is perfect.

Thanks to all.


--