close call
 

Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches
from disaster.

Some of you may say I should have shut it, but when doing a lot of rough
cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.


--
Jeff

close call
 

woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches from disaster.

Some of you may say I should have shut it, but when doing a lot of rough
cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.



Didn't you just say you were putting the SawStop on hold till next year?
:-(

Glad you dodged this one if you are serious about a new saw I'd say start
shopping for what you want.

close call
 

"woodchucker" wrote:

Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand
almost hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw
running while I went to pick up the next piece to rough cut. And
that's when I stepped on the offcut rolled my ankle and wound up
with my hand inches from disaster.

Some of you may say I should have shut it, but when doing a lot of
rough cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.
------------------------------------------------------------------
Remember, "Haste makes waste"?

Safety is of prime concern

For you it is a hobby. Approach each task that way.

Glad to see you dodged a bullet.

I'm reminded of one of my most basic rules from my sailing days.

When asked when I would arrive at a particular destination, my answer
was always the same.

"Whenever I get there, I'll be there, depends on mother nature".

Same with woodworking.

Mother nature is in charge and sometimes she is a bitch.

Take care.

Lew

close call
 

Glad to hear you avoided the blade, Jeff. I've reached that age where I mentally walk through each step in a TS operation -- router table, too -- as there are too many things that can bite you and they all happen too flippin' fast.

Larry

On Wednesday, September 18, 2013 8:48:28 PM UTC-5, woodchucker wrote:
Even careful people can get burned.

I was back in the shop tonight, just a few minutes ago my hand almost

hit the TS blade.



I was prepping some wood, and threw the offcut in the bucket, but it

missed. I didn't know it landed one step away. I left the saw running

while I went to pick up the next piece to rough cut. And that's when I

stepped on the offcut rolled my ankle and wound up with my hand inches

from disaster.



Some of you may say I should have shut it, but when doing a lot of rough

cutting I just grab the next piece... but I get it.



Too close for comfort.. My ankle will be sore tomorrow... when the

adrenaline stops pumping.





--

Jeff

close call
 

woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches
from disaster.

Some of you may say I should have shut it, but when doing a lot of
rough cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.


Congratulations on your safe landing!

Bill

close call
 

On 9/18/2013 9:48 PM, woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches
from disaster.

Some of you may say I should have shut it, but when doing a lot of rough
cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.



You may wish to consider my solution to cutting many pieces of wood with
the same saw setup.

I built a bench that is on wheels. It is the same height as the table
on my saw. When doing multiple cuts, I move the bench into a position
next to the saw. All I have to do is rotate toward the bench, pick up
the piece, rotate back to the saw, make the cut, Rotate back to the
bench deposit the newly cut piece and pick up the next. No bending, No
major movement. If something falls off of the saw or bench I have to
get away from the saw to retrieve it.


This bench also functions as my work bench and has shelves for storage
underneath and cabinets in the ends.

When ripping it can be moved to the far side of the saw to accept the
boards as it comes off of the saw.

close call
 

Like when a break goes, and the saw is left in the on position.
This happens at a worksite with extension cords.....
Yes, accidents, usually happen when we are in a hurry.
Turning off a saw.......whenever it is not in use, is important.
john

"woodchucker" wrote in message
...

Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches
from disaster.

Some of you may say I should have shut it, but when doing a lot of rough
cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.


--
Jeff

close call
 

On Wednesday, September 18, 2013 8:48:28 PM UTC-5, woodchucker wrote:
Even careful people can get burned.

I was back in the shop tonight, just a few minutes ago my hand almost

hit the TS blade.



I was prepping some wood, and threw the offcut in the bucket, but it

missed. I didn't know it landed one step away. I left the saw running

while I went to pick up the next piece to rough cut. And that's when I

stepped on the offcut rolled my ankle and wound up with my hand inches

from disaster.



Some of you may say I should have shut it, but when doing a lot of rough

cutting I just grab the next piece... but I get it.



Too close for comfort.. My ankle will be sore tomorrow... when the

adrenaline stops pumping.





--

Jeff

That will wake you up in the morning.

Glad to hear you're ok.

close call
 

On 9/18/2013 6:48 PM, woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I assume you are not using a guard ?

close call
 

On 9/19/13 9:17 AM, Pat Barber wrote:
On 9/18/2013 6:48 PM, woodchucker wrote:
Even careful people can get burned. I was back in the shop tonight,
just a few minutes ago my hand almost hit the TS blade.

I assume you are not using a guard ?


Guards don't do much for a handing slipping forward into the blade.
I'm surprised how easy this happens when your footing slips.

I believe the non-ability of traditional saw blade guards to protect
again this was was of the deciding factors that got so many new laws and
regs passed for Gass' saw-stop.


--

-MIKE-

"Playing is not something I do at night, it's my function in life"
--Elvin Jones (1927-2004)
--
http://mikedrums.com

---remove "DOT" ^^^^ to reply

close call
 

On 9/19/2013 10:17 AM, Pat Barber wrote:
On 9/18/2013 6:48 PM, woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I assume you are not using a guard ?

Of course not.
I have a splitter only.
I don't think I would use it even with the sawstop unless it sucked up
all the dust.

But I don't know, I've never had a riving knife or easily on off unit.

--
Jeff

close call
 

On 9/19/2013 8:57 AM, Keith Nuttle wrote:
On 9/18/2013 9:48 PM, woodchucker wrote:
Even careful people can get burned.
I was back in the shop tonight, just a few minutes ago my hand almost
hit the TS blade.

I was prepping some wood, and threw the offcut in the bucket, but it
missed. I didn't know it landed one step away. I left the saw running
while I went to pick up the next piece to rough cut. And that's when I
stepped on the offcut rolled my ankle and wound up with my hand inches
from disaster.

Some of you may say I should have shut it, but when doing a lot of rough
cutting I just grab the next piece... but I get it.

Too close for comfort.. My ankle will be sore tomorrow... when the
adrenaline stops pumping.



You may wish to consider my solution to cutting many pieces of wood with
the same saw setup.

I built a bench that is on wheels. It is the same height as the table
on my saw. When doing multiple cuts, I move the bench into a position
next to the saw. All I have to do is rotate toward the bench, pick up
the piece, rotate back to the saw, make the cut, Rotate back to the
bench deposit the newly cut piece and pick up the next. No bending, No
major movement. If something falls off of the saw or bench I have to
get away from the saw to retrieve it.


This bench also functions as my work bench and has shelves for storage
underneath and cabinets in the ends.

When ripping it can be moved to the far side of the saw to accept the
boards as it comes off of the saw.



I have a utility cart that I sometimes use when its not loaded with junk
as it is right now in my storage area.

I have not finished my new finishing area and all the crap is on it.



--
Jeff

close call
 

On 9/19/2013 3:08 PM, woodchucker wrote:

I have a splitter only.
I don't think I would use it even with the sawstop unless it sucked up
all the dust.

But I don't know, I've never had a riving knife or easily on off unit.

Consider a overhead guard like the Biesemeyer or Delta.

I have Biesemeyer and really use it a lot more than a conventional
guard.

http://www.deltamachinery.com/access...category_id=45

or

http://www.deltamachinery.com/access...ws/item/34-976

close call
 

On Fri, 20 Sep 2013 08:09:06 -0700, Pat Barber
wrote:

On 9/19/2013 3:08 PM, woodchucker wrote:

I have a splitter only.
I don't think I would use it even with the sawstop unless it sucked up
all the dust.

But I don't know, I've never had a riving knife or easily on off unit.

Consider a overhead guard like the Biesemeyer or Delta.

I have Biesemeyer and really use it a lot more than a conventional
guard.

http://www.deltamachinery.com/access...category_id=45

$600?!

or

http://www.deltamachinery.com/access...ws/item/34-976


$900?!!!

Yikes! I do have the Biesemeyer splitter but they're sure proud of
those guards!