Quick review -- Incra box joint jig
 

Bottom line first: Creates accurate, repeatable finger joints with little opportunity for operator error.

Pros: relatively easy set up with good print directions and a nicely done DVD. My test joints were a tad loose, but the spacer is adjustable in 0.001 increments and with a bit of fiddling was able to create snug-fitting joints. Good attention to safety with a shield that covers the blade (or bit if you're using a router table).

Cons: I tried to use their chart for creating an odd number of fingers using 1/4 inch dado and somehow ended up with an even number of fingers. Since I am behind on delivery on this project, I decided to go forward with the less than desirable finger configuration for the five drawers for the jewelry armoire. (My daughter won't mind and my wife didn't notice). Methinks I need to read through this section again.

Larry

Quick review -- Incra box joint jig
 

On 6/5/2013 9:39 PM, Gramp's shop wrote:
Bottom line first: Creates accurate, repeatable finger joints with little opportunity for operator error.

Pros: relatively easy set up with good print directions and a nicely done DVD. My test joints were a tad loose, but the spacer is adjustable in 0.001 increments and with a bit of fiddling was able to create snug-fitting joints. Good attention to safety with a shield that covers the blade (or bit if you're using a router table).

Cons: I tried to use their chart for creating an odd number of fingers using 1/4 inch dado and somehow ended up with an even number of fingers. Since I am behind on delivery on this project, I decided to go forward with the less than desirable finger configuration for the five drawers for the jewelry armoire. (My daughter won't mind and my wife didn't notice). Methinks I need to read through this section again.

Larry



Yea, read it again, and or watch that part on the DVD again. I did the
odd number of fingers by accident and it worked well.

Quick review -- Incra box joint jig
 

Gramp's shop wrote:
Bottom line first: Creates accurate, repeatable finger joints with
little opportunity for operator error.

Pros: relatively easy set up with good print directions and a nicely
done DVD. My test joints were a tad loose, but the spacer is
adjustable in 0.001 increments and with a bit of fiddling was able to
create snug-fitting joints. Good attention to safety with a shield
that covers the blade (or bit if you're using a router table).

Cons: I tried to use their chart for creating an odd number of
fingers using 1/4 inch dado and somehow ended up with an even number
of fingers. Since I am behind on delivery on this project, I decided
to go forward with the less than desirable finger configuration for
the five drawers for the jewelry armoire. (My daughter won't mind and
my wife didn't notice). Methinks I need to read through this section
again.

Larry

What??? You read the intructions first? No wonder you're having problems.
Go buy the Guy Book at your favorite bookstore...

--

-Mike-

Quick review -- Incra box joint jig
 

On Wednesday, June 5, 2013 10:32:30 PM UTC-5, Mike Marlow wrote:
Gramp's shop wrote:

Bottom line first: Creates accurate, repeatable finger joints with

little opportunity for operator error.



Pros: relatively easy set up with good print directions and a nicely

done DVD. My test joints were a tad loose, but the spacer is

adjustable in 0.001 increments and with a bit of fiddling was able to

create snug-fitting joints. Good attention to safety with a shield

that covers the blade (or bit if you're using a router table).



Cons: I tried to use their chart for creating an odd number of

fingers using 1/4 inch dado and somehow ended up with an even number

of fingers. Since I am behind on delivery on this project, I decided

to go forward with the less than desirable finger configuration for

the five drawers for the jewelry armoire. (My daughter won't mind and

my wife didn't notice). Methinks I need to read through this section

again.



Larry



What??? You read the intructions first? No wonder you're having problems.

Go buy the Guy Book at your favorite bookstore...



--



-Mike-



This was the first time I actually looked at any instructions for anything I've ever purchased. You're absolutely right ... and I'll never make that mistake again.

Quick review -- Incra box joint jig
 

Gramp's shop wrote:
On Wednesday, June 5, 2013 10:32:30 PM UTC-5, Mike Marlow wrote:


What??? You read the intructions first? No wonder you're having
problems.

Go buy the Guy Book at your favorite bookstore...

--

-Mike-



This was the first time I actually looked at any instructions for
anything I've ever purchased. You're absolutely right ... and I'll
never make that mistake again.

There now - doesn't that feel better?

--

-Mike-

Quick review -- Incra box joint jig
 

On 6/6/2013 8:01 AM, Gramp's shop wrote:
On Wednesday, June 5, 2013 10:32:30 PM UTC-5, Mike Marlow wrote:
Gramp's shop wrote:

Bottom line first: Creates accurate, repeatable finger joints with

little opportunity for operator error.



Pros: relatively easy set up with good print directions and a nicely

done DVD. My test joints were a tad loose, but the spacer is

adjustable in 0.001 increments and with a bit of fiddling was able to

create snug-fitting joints. Good attention to safety with a shield

that covers the blade (or bit if you're using a router table).



Cons: I tried to use their chart for creating an odd number of

fingers using 1/4 inch dado and somehow ended up with an even number

of fingers. Since I am behind on delivery on this project, I decided

to go forward with the less than desirable finger configuration for

the five drawers for the jewelry armoire. (My daughter won't mind and

my wife didn't notice). Methinks I need to read through this section

again.



Larry



What??? You read the intructions first? No wonder you're having problems.

Go buy the Guy Book at your favorite bookstore...



--



-Mike-



This was the first time I actually looked at any instructions for anything I've ever purchased. You're absolutely right ... and I'll never make that mistake again.



You did not even read the instructions for setting the clock on your
60's VCR? LOL

Quick review -- Incra box joint jig
 

SNIP


You did not even read the instructions for setting the clock on your

60's VCR? LOL

My VCR came with a brunette who handled all the tech stuff like setting the clock, recording shows and playback. Didn't yours? G

Quick review -- Incra box joint jig
 

SNIP


You did not even read the instructions for setting the clock on your
60's VCR? LOL

My VCR came with a brunette who handled all the tech stuff like setting the clock, recording shows and playback. Didn't yours? G


.... mine came with the blonde ...
.........hence the 12:00 12:00 12:00

jt


--- news://freenews.netfront.net/ - complaints: ---

Quick review -- Incra box joint jig
 

On 6/6/2013 12:42 PM, Gramp's shop wrote:
SNIP


You did not even read the instructions for setting the clock on your

60's VCR? LOL

My VCR came with a brunette who handled all the tech stuff like setting the clock, recording shows and playback. Didn't yours? G



We could not afford that. LOL