Siver soldering bandsaw blade
 

Hello
Not having great luck. I have some rolls of bandsaw blade stock. Any hints
or tips greatly appreciated. Can flux go bad or get contaminated? It seems
the solder melts but doesn't have that nice flow , but instead just lumps up
into a nice cold solder joint. I cleaned the joints well , but when I apply
the heat til it gets red hot I get this black gunk gathering at the ends of
the blades. Is there a different flux for non ferrous & ferrous metals? I've
silver soldered before with great success.Thanks.
ron

Siver soldering bandsaw blade
 

One way my dad use to solder blades is prepare the ends of the blades
with a tapered lap joint. Apply flux and a piece of flat silver
solder, then using a set of soldering pliers that have been heated to
red hot with an acetalen (sorry for spelling) torch, then gripping the
band with the pliers.

His pliers where about 18" long, (end to end). The heating end was 1/2"
square iron stock.

Should only take 30 secs or so to solder the joint.

As for the black gunk, it sounds like you are getting contamination from
your torch.

Hope this helps. If needed, I could probably get a pic of the pliers.
Just let me know.

Just remove the dashes from my address

James



Ronald Murray wrote:
Hello
Not having great luck. I have some rolls of bandsaw blade stock. Any hints
or tips greatly appreciated. Can flux go bad or get contaminated? It seems
the solder melts but doesn't have that nice flow , but instead just lumps up
into a nice cold solder joint. I cleaned the joints well , but when I apply
the heat til it gets red hot I get this black gunk gathering at the ends of
the blades. Is there a different flux for non ferrous & ferrous metals? I've
silver soldered before with great success.Thanks.
ron

Siver soldering bandsaw blade
 

drop the .clark to



James wrote:
One way my dad use to solder blades is prepare the ends of the blades
with a tapered lap joint. Apply flux and a piece of flat silver
solder, then using a set of soldering pliers that have been heated to
red hot with an acetalen (sorry for spelling) torch, then gripping the
band with the pliers.

His pliers where about 18" long, (end to end). The heating end was 1/2"
square iron stock.

Should only take 30 secs or so to solder the joint.

As for the black gunk, it sounds like you are getting contamination from
your torch.

Hope this helps. If needed, I could probably get a pic of the pliers.
Just let me know.

Just remove the dashes from my address

James



Ronald Murray wrote:

Hello
Not having great luck. I have some rolls of bandsaw blade stock. Any
hints
or tips greatly appreciated. Can flux go bad or get contaminated? It
seems
the solder melts but doesn't have that nice flow , but instead just
lumps up
into a nice cold solder joint. I cleaned the joints well , but when I
apply
the heat til it gets red hot I get this black gunk gathering at the
ends of
the blades. Is there a different flux for non ferrous & ferrous
metals? I've
silver soldered before with great success.Thanks.
ron

Siver soldering bandsaw blade
 

In article ,
"Ronald Murray" wrote:

Not having great luck. I have some rolls of bandsaw blade stock. Any hints
or tips greatly appreciated. Can flux go bad or get contaminated? It seems
the solder melts but doesn't have that nice flow , but instead just lumps up
into a nice cold solder joint. I cleaned the joints well , but when I apply
the heat til it gets red hot I get this black gunk gathering at the ends of
the blades. Is there a different flux for non ferrous & ferrous metals? I've
silver soldered before with great success.Thanks.

I believe flux can go bad. I've not soldered B/S blades, but this past
winter I was intalling a new bath & shower control valve. The flux I had
on hand caused the solder to behave exactly as you described. I bought a
new container and the soldering went smoothly and flowed just as you
would expect.

--
Owen Lowe and his Fly-by-Night Copper Company
Offering a shim for the Porter-Cable 557 type 2 fence design.
http://www.flybynightcoppercompany.com
http://www.easystreet.com/~onlnlowe/index.html