Dubby Crosscut Sled
 

Someone wants to sell me a used, left-side DCS. Leon
mentioned this as a good accessory for the Ridgid TS in
a previous exchange.
No picture or elaboration is had as yet but I do have a
couple of questions.

1. Researching the sleds after Leon's recommendation, I read a
comment that individual units only fit certain brands/models of
table saws. Although no clarification was given, my assumption
was this had to do with specifics of the miter slot to blade distance.
If so--or if not--and assuming the offered sled was made for
another make/model of saw, is it possible to make it fit the Ridgid
(or other TS) by some reasonably uninvolved modification?

2. If we have a green light on point 1, what are the points for
physical examination on this used DCS?

A price figure remains to be mentioned, but somehow that
will come up too. All replies are appreciated.

Regards,

Edward Hennessey

Dubby Crosscut Sled
 

On Feb 9, 10:21*pm, "Edward Hennessey"
wrote:
Someone wants to sell me a used, left-side DCS. Leon
mentioned this as a good accessory for the Ridgid TS in
a previous exchange.
No picture or elaboration is had as yet but I do have a
couple of questions.

1. Researching the sleds after Leon's recommendation, I read a
comment that individual units only fit certain brands/models of
table saws. Although no clarification was given, my assumption
was this had to do with specifics of the miter slot to blade distance.
If so--or if not--and assuming the offered sled was made for
another make/model of saw, is it possible to make it fit the Ridgid
(or other TS) by some reasonably uninvolved modification?

2. If we have a green light on point 1, what are the points for
physical examination on this used DCS?

*A price figure remains to be mentioned, but somehow that
will come up too. All replies are appreciated.

Regards,

Edward Hennessey

Haven't used it myself but the ol' dubby himself does a hell of a demo
with that thang. Made me want one.

Dubby Crosscut Sled
 

"Edward Hennessey" wrote in message
m...
Someone wants to sell me a used, left-side DCS. Leon
mentioned this as a good accessory for the Ridgid TS in
a previous exchange.
No picture or elaboration is had as yet but I do have a
couple of questions.

1. Researching the sleds after Leon's recommendation, I read a
comment that individual units only fit certain brands/models of
table saws. Although no clarification was given, my assumption
was this had to do with specifics of the miter slot to blade distance.
If so--or if not--and assuming the offered sled was made for
another make/model of saw, is it possible to make it fit the Ridgid
(or other TS) by some reasonably uninvolved modification?

I would not consider buying used unless I was getting the used jig for next
to nothing. The jigs are made to fit specific saws and even then the jig is
tweeked "by you and your saw" to fit your saw specifically, not all of the
same kind of saw. Basically a new sled will be too wide to pass near the
blade with out being cut by the blade. Cutting the sled with the blade is
part of the initial set up. You use the new cut edge as a reference, it is
the edge of the cut. Very handy for measuring from that edge to the stop on
the fence for accurate length cuts. Having said that IIRC you can order or
make new sleds and simply transfer the parts, fence, stop, angle gauge, etc.



2. If we have a green light on point 1, what are the points for
physical examination on this used DCS?

Obvious damage.



A price figure remains to be mentioned, but somehow that
will come up too. All replies are appreciated.

I bought both my left and right Dubby jigs at the same time. There are
times that having a jig for both sides is handy, think cutting asymmetrical
moldings on both ends. I got a sizeable discount when I bought both at the
same time. Actually my wife did, she ordered on the phone and mentioned
"show pricing", and they gave her show pricing.

I got my Dubby jigs at Christmas 1999 IIRC. I have never had to recalibrate
either one.

Dubby Crosscut Sled
 

"Leon" wrote in message
...

"Edward Hennessey" wrote in message
m...
Someone wants to sell me a used, left-side DCS. Leon
mentioned this as a good accessory for the Ridgid TS in
a previous exchange.
No picture or elaboration is had as yet but I do have a
couple of questions.

1. Researching the sleds after Leon's recommendation, I read a
comment that individual units only fit certain brands/models of
table saws. Although no clarification was given, my assumption
was this had to do with specifics of the miter slot to blade
distance.
If so--or if not--and assuming the offered sled was made for
another make/model of saw, is it possible to make it fit the Ridgid
(or other TS) by some reasonably uninvolved modification?

I would not consider buying used unless I was getting the used jig
for next to nothing. The jigs are made to fit specific saws and
even then the jig is tweeked "by you and your saw" to fit your saw
specifically, not all of the same kind of saw. Basically a new sled
will be too wide to pass near the blade with out being cut by the
blade. Cutting the sled with the blade is part of the initial set
up. You use the new cut edge as a reference, it is the edge of the
cut. Very handy for measuring from that edge to the stop on the
fence for accurate length cuts. Having said that IIRC you can order
or make new sleds and simply transfer the parts, fence, stop, angle
gauge, etc.

Leon:

Thanks. I got it. The printed information on the Dubby site did not
make
what you clearly said apparent. This sled has alreay been altered.

Regards,

Edward Hennessey




2. If we have a green light on point 1, what are the points for
physical examination on this used DCS?

Obvious damage.



A price figure remains to be mentioned, but somehow that
will come up too. All replies are appreciated.

I bought both my left and right Dubby jigs at the same time. There
are times that having a jig for both sides is handy, think cutting
asymmetrical moldings on both ends. I got a sizeable discount when
I bought both at the same time. Actually my wife did, she ordered
on the phone and mentioned "show pricing", and they gave her show
pricing.

I got my Dubby jigs at Christmas 1999 IIRC. I have never had to
recalibrate either one.

Dubby Crosscut Sled
 

"Edward Hennessey" wrote in message
...


Leon:

Thanks. I got it. The printed information on the Dubby site did not make
what you clearly said apparent. This sled has alreay been altered.

Regards,

Edward Hennessey


In case you have not yet found this,
http://www.in-lineindustries.com/New...y%20Manual.pdf , look at the
bottom of page 3 for the cutting step during set up.

Dubby Crosscut Sled
 

"Leon" wrote in message
...

"Edward Hennessey" wrote in message
...


Leon:

Thanks. I got it. The printed information on the Dubby site did not make
what you clearly said apparent. This sled has alreay been altered.

Regards,

Edward Hennessey


In case you have not yet found this,
http://www.in-lineindustries.com/New...y%20Manual.pdf , look at the
bottom of page 3 for the cutting step during set up.

If the base has already been cut too narrow by a reasonably small amount
(say an inch or so), it is easy to redo. It is possible to glue a strip of
hardwood to the cut edge and then recut the sled to fit your saw. I did
that to one that had been damaged with no problem. Older models had a
wooden fence while I believe the newer models have a metal fence.

Dubby Crosscut Sled
 

"Leon" wrote in message
...

"Edward Hennessey" wrote in message
...


Leon:

Thanks. I got it. The printed information on the Dubby site did not
make
what you clearly said apparent. This sled has alreay been altered.

Regards,

Edward Hennessey


In case you have not yet found this,
http://www.in-lineindustries.com/New...y%20Manual.pdf , look at
the bottom of page 3 for the cutting step during set up.


Leon:

You are the man. You did my work for me. I apologize but thank you
more.

Regards,

Edward Hennessey

Dubby Crosscut Sled
 

"John" wrote in message
...

"Leon" wrote in message
...

"Edward Hennessey" wrote in message
...


Leon:

Thanks. I got it. The printed information on the Dubby site did
not make
what you clearly said apparent. This sled has alreay been altered.

Regards,

Edward Hennessey


In case you have not yet found this,
http://www.in-lineindustries.com/New...y%20Manual.pdf , look at
the bottom of page 3 for the cutting step during set up.

If the base has already been cut too narrow by a reasonably small
amount (say an inch or so), it is easy to redo. It is possible to
glue a strip of hardwood to the cut edge and then recut the sled to
fit your saw. I did that to one that had been damaged with no
problem. Older models had a wooden fence while I believe the newer
models have a metal fence.

JS:

Thank you kindly for the help. Your advice is intelligent.
If the seller is willing to make an accomodation on price,
we'll see.

Regards,

Edward Hennessey

Dubby Crosscut Sled
 

On 2/11/2011 1:50 AM, Edward Hennessey wrote:

Leon:

You are the man. You did my work for me.

Edward Hennessey


That a Leon trait for you .... working with him in the shop is like
having an extra pair of hands at the end of your arms.

--
www.e-woodshop.net
Last update: 4/15/2010
KarlC@ (the obvious)

Dubby Crosscut Sled
 

"Swingman" wrote in message
...
On 2/11/2011 1:50 AM, Edward Hennessey wrote:

Leon:

You are the man. You did my work for me.

Edward Hennessey


That a Leon trait for you .... working with him in the shop is like
having an extra pair of hands at the end of your arms.

--
www.e-woodshop.net
Last update: 4/15/2010
KarlC@ (the obvious)

KC:

That's a good shout out to Leon. But I want to see the look
on the fingerprinting guy.

Regards,

Edward Hennessey