Patches
 

I cut notches in the wrong place on the top of a panel. I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. What can I do to disguise the patch as much as
possible?

Puckdropper

Patches
 

Puckdropper wrote:
I cut notches in the wrong place on the top of a panel. I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. What can I do to disguise the patch as much as
possible?

Puckdropper

Sorry to hear of your dilemma. A pic would probably help folks who have
BTDT to help you. Good luck.

Bill

Patches
 

It would also help to know if this was a furniture piece or a utility piece.
But by all means, a picture would help.

Deb



wrote:

I cut notches in the wrong place on the top of a panel. I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. What can I do to disguise the patch as much as
possible?

Puckdropper

Patches
 

On Jan 3, 3:58*am, Puckdropper puckdropper(at)yahoo(dot)com wrote:
I cut notches in the wrong place on the top of a panel. *I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. *What can I do to disguise the patch as much as
possible?

What an open-ended question! Depends on the wood, the location of the
notches, the type of finish you were planning on, whether you want to
use toners or glazes, etc.

Furnish some pictures forthwith!

R

Patches
 

What type of panel?

Wall panelling?
Inset furniture panel?
Laminated wood?
Cabinet door raised panel?


"Puckdropper" puckdropper(at)yahoo(dot)com wrote in message
b.com...
I cut notches in the wrong place on the top of a panel. I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. What can I do to disguise the patch as much as
possible?

Puckdropper

Patches
 

Bill wrote in :

Puckdropper wrote:
I cut notches in the wrong place on the top of a panel. I think the
best solution will be to patch it by gluing pieces in the proper
place and cutting the notches again. What can I do to disguise the
patch as much as possible?

Puckdropper

Sorry to hear of your dilemma. A pic would probably help folks who
have BTDT to help you. Good luck.

Bill


I've uploaded the sketchup diagram to A.B.P.W. This is the plan diagram,
not what actually resulted. The sockets for the top runner dovetails
were cut in the wrong place, and this is what would need to be repaired.

The piece is designed to carry gingerbread houses safely, so is more of a
utility piece than fine furniture, but I'd like it to look as nice as
possible.

Puckdropper

Patches
 

RicodJour wrote in
:

On Jan 3, 3:58*am, Puckdropper puckdropper(at)yahoo(dot)com wrote:
I cut notches in the wrong place on the top of a panel. *I think the
be
st
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. *What can I do to disguise the patch as
much
as
possible?

What an open-ended question! Depends on the wood, the location of the
notches, the type of finish you were planning on, whether you want to
use toners or glazes, etc.

Furnish some pictures forthwith!

R


The wood is just standard knotty pine. I've got plenty of pieces of the
same thickness (off cuts). The finish will be shellac, unless I have to
put poly on top to protect the shellac. (I don't believe I'll need it.)

Puckdropper

Patches
 

On Jan 3, 2:55*pm, Puckdropper puckdropper(at)yahoo(dot)com wrote:

I've uploaded the sketchup diagram to A.B.P.W. *This is the plan diagram,
not what actually resulted. *The sockets for the top runner dovetails
were cut in the wrong place, and this is what would need to be repaired.

The piece is designed to carry gingerbread houses safely, so is more of a
utility piece than fine furniture, but I'd like it to look as nice as
possible.

In your situation I'd be tempted to just rip the pieces down to
eliminate the notches, glue on a new piece and recut the notches.
That would probably be almost as quick as patching and recutting and
would be pretty much undetectable if done right.

R

Patches
 

Puckdropper wrote:
....
... The sockets for the top runner dovetails
were cut in the wrong place, and this is what would need to be repaired.
....

My newsserver doesn't carry binary groups but...

I'd wonder if couldn't simply cut the panel down and then glue a strip
of the same material on and resize the overall panel wouldn't be both
simplest and least obvious repair...

--

Patches
 

RicodJour wrote in
:


In your situation I'd be tempted to just rip the pieces down to
eliminate the notches, glue on a new piece and recut the notches.
That would probably be almost as quick as patching and recutting and
would be pretty much undetectable if done right.

R


Once I rip that piece down, I've got 3/8" of original material left. After
gluing (with Titebond II), will the new piece be as strong or stronger than
the old? I need to attach handles at some point.

I do agree that will be the most invisible fix, but just don't want to see
the whole piece come apart as I make the cut.

Puckdropper

Patches
 

Puckdropper wrote:
RicodJour wrote in
:

In your situation I'd be tempted to just rip the pieces down to
eliminate the notches, glue on a new piece and recut the notches.
That would probably be almost as quick as patching and recutting and
would be pretty much undetectable if done right.

R


Once I rip that piece down, I've got 3/8" of original material left. After
gluing (with Titebond II), will the new piece be as strong or stronger than
the old? I need to attach handles at some point.
....

A good joint w/ even white glue is stronger than the wood so yes, it
should be plenty strong enough.

--

Patches
 

On 03 Jan 2011 19:55:34 GMT, Puckdropper
puckdropper(at)yahoo(dot)com wrote:

Bill wrote in :

Puckdropper wrote:
I cut notches in the wrong place on the top of a panel. I think the
best solution will be to patch it by gluing pieces in the proper
place and cutting the notches again. What can I do to disguise the
patch as much as possible?

Puckdropper

Sorry to hear of your dilemma. A pic would probably help folks who
have BTDT to help you. Good luck.

Bill


I've uploaded the sketchup diagram to A.B.P.W. This is the plan diagram,
not what actually resulted. The sockets for the top runner dovetails
were cut in the wrong place, and this is what would need to be repaired.

The piece is designed to carry gingerbread houses safely, so is more of a
utility piece than fine furniture, but I'd like it to look as nice as
possible.

Cut replacement pieces and put small wedges in to fill gaps, making
sure to align the grain as best you can. If you were really
concerned, I'm sure you'd just replace the panel.

--
You do not need a parachute to skydive.
You only need a parachute to skydive twice.

Patches
 

Puckdropper wrote:
wrote in :

Puckdropper wrote:
I cut notches in the wrong place on the top of a panel. I think the
best solution will be to patch it by gluing pieces in the proper
place and cutting the notches again. What can I do to disguise the
patch as much as possible?

Puckdropper

Sorry to hear of your dilemma. A pic would probably help folks who
have BTDT to help you. Good luck.

Bill


I've uploaded the sketchup diagram to A.B.P.W. This is the plan diagram,
not what actually resulted. The sockets for the top runner dovetails
were cut in the wrong place, and this is what would need to be repaired.

The piece is designed to carry gingerbread houses safely, so is more of a
utility piece than fine furniture, but I'd like it to look as nice as
possible.

Puckdropper

I can not find it in A.P.B.W why not post a picture with tinypic,picassa
or photobucket etc and just supply the url?

Patches
 

F Murtz wrote in
:


I can not find it in A.P.B.W why not post a picture with
tinypic,picassa or photobucket etc and just supply the url?



It shows up just fine in A.B.P.W for me, but for those who can't see it
here's the picture on my website.

http://www.puckdroppersplace.us/othe...%20carrier.jpg

Puckdropper

Patches
 

On 04 Jan 2011 05:47:58 GMT, Puckdropper
puckdropper(at)yahoo(dot)com wrote:

F Murtz wrote in
:


I can not find it in A.P.B.W why not post a picture with
tinypic,picassa or photobucket etc and just supply the url?



It shows up just fine in A.B.P.W for me, but for those who can't see it
here's the picture on my website.

http://www.puckdroppersplace.us/othe...%20carrier.jpg

I don't see any "panel" anywhere, Pucky. What up wi dat?
Nice dovies on top and -slot- mortises? Why not real mortises?

--
You do not need a parachute to skydive.
You only need a parachute to skydive twice.

Patches
 

Larry Jaques wrote in
:


I don't see any "panel" anywhere, Pucky. What up wi dat?
Nice dovies on top and -slot- mortises? Why not real mortises?

--
You do not need a parachute to skydive.
You only need a parachute to skydive twice.


The slot mortises hold the panel in place. The panel was not shown on the
diagram because it was easier to build than to draw.

Puckdropper

Patches
 

On Jan 3, 12:58*am, Puckdropper puckdropper(at)yahoo(dot)com wrote:
I cut notches in the wrong place on the top of a panel. *I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. *What can I do to disguise the patch as much as
possible?

Cut the patch symmetrically around a knot?

Patches
 

On Thu, 6 Jan 2011 11:16:45 -0800 (PST), whit3rd
wrote:

On Jan 3, 12:58*am, Puckdropper puckdropper(at)yahoo(dot)com wrote:
I cut notches in the wrong place on the top of a panel. *I think the best
solution will be to patch it by gluing pieces in the proper place and
cutting the notches again. *What can I do to disguise the patch as much as
possible?

Cut the patch symmetrically around a knot?

No, pop the knot out and coat it with 30 weight oi...oops, wrong
thread.

--
A smile is the shortest distance between two people.
-- Victor Borge