Jointer Help
 

Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run it
through the other way. It should remove the pencil marks on the second pass.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Can anyone help me with troubleshooting?

Jointer Help
 

In theory that would be a tru test if you started with a perfectly
flat board. But if not, then it means nothing. Also, technique can
have a big effect on jointers also.

The key factors a

1. The infeed and outfeed tables should be totally parallel in both
directions (side to side and end to end). This is easiest to check
when infeed table is raised to be equal height to outfeed but should
remain true after infeed is lowered for usage(harder to check). So any
adjustments to make tables parallel are first step.

2. Raise cutters so they are equal to outfeed table height. There are
little frames with magnet that help set this up. You loosen the
blades, run the head to center the cutter at highest point and lock
down each blade. Use can use a straight edge if you don't have magnet
gizmo.

3. Side fence should lock in at 90 degrees exact to table.

Not much else to do.

On Apr 1, 3:19*pm, The Wolf wrote:
Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run it
through the other way. It should remove the pencil marks on the second pass.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Can anyone help me with troubleshooting?

Jointer Help
 

On 4/1/2010 5:19 PM, The Wolf wrote:
Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run it
through the other way. It should remove the pencil marks on the second pass.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Can anyone help me with troubleshooting?

My advice would be to ignore it ... too many other variables at play for
that method to be remotely reliable, IMO.

The proof is in the pudding ... using a proper and practised technique,
when a single pass fully engages the board from end to end, and results
is a flat surface, then the pudding is done.

--
www.e-woodshop.net
Last update: 10/22/08
KarlC@ (the obvious)

Jointer Help
 

On 4/1/10 5:02 PM, in article , "Doug
Miller" wrote:

This thing is a 12" monster. I only have a 4' level to use as a straight
edge. Trying to improvise. I suspect the outfeed table is sloped towards
the floor.

The bed is level.

In article
,
"SonomaProducts.com" wrote:
In theory that would be a tru test if you started with a perfectly
flat board. But if not, then it means nothing. Also, technique can
have a big effect on jointers also.

The key factors a

1. The infeed and outfeed tables should be totally parallel in both
directions (side to side and end to end). This is easiest to check
when infeed table is raised to be equal height to outfeed but should
remain true after infeed is lowered for usage(harder to check). So any
adjustments to make tables parallel are first step.

2. Raise cutters so they are equal to outfeed table height.

IME, 0.002" to 0.003" above outfeed table height works better.

There are
little frames with magnet that help set this up. You loosen the
blades, run the head to center the cutter at highest point and lock
down each blade. Use can use a straight edge if you don't have magnet
gizmo.

3. Side fence should lock in at 90 degrees exact to table.

Not much else to do.

On Apr 1, 3:19=A0pm, The Wolf wrote:
Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run i=
t
through the other way. It should remove the pencil marks on the second pa=
ss.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Can anyone help me with troubleshooting?

Jointer Help
 

In article , "SonomaProducts.com" wrote:
In theory that would be a tru test if you started with a perfectly
flat board. But if not, then it means nothing. Also, technique can
have a big effect on jointers also.

The key factors a

1. The infeed and outfeed tables should be totally parallel in both
directions (side to side and end to end). This is easiest to check
when infeed table is raised to be equal height to outfeed but should
remain true after infeed is lowered for usage(harder to check). So any
adjustments to make tables parallel are first step.

2. Raise cutters so they are equal to outfeed table height.

IME, 0.002" to 0.003" above outfeed table height works better.

There are
little frames with magnet that help set this up. You loosen the
blades, run the head to center the cutter at highest point and lock
down each blade. Use can use a straight edge if you don't have magnet
gizmo.

3. Side fence should lock in at 90 degrees exact to table.

Not much else to do.

On Apr 1, 3:19=A0pm, The Wolf wrote:
Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run i=
t
through the other way. It should remove the pencil marks on the second pa=
ss.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Can anyone help me with troubleshooting?

Jointer Help
 

In article , The Wolf wrote:

This thing is a 12" monster. I only have a 4' level to use as a straight
edge. Trying to improvise. I suspect the outfeed table is sloped towards
the floor.

The bed is level.

FWIW, in operation it doesn't matter *at all* if the tables are level, as long
as they're parallel to each other. If you can make one of them dead level,
though, it makes it easier to tell when they're parallel: if you can make
the other one dead level too, then they must be parallel. With a machine as
large as yours, it may well be much easier to check for level than for
parallel -- as long as your level is accurate.

Jointer Help
 

On 04/01/2010 04:19 PM, The Wolf wrote:
Someone showed me a way to check the jointer. Joint the first 12" of a
board, pull it back scribble pencil marks on it. Turn it around and run it
through the other way. It should remove the pencil marks on the second pass.

At any rate I am working on a jointer manufactured in 1944. It takes 2-3
passes to remove the pencil marks.

Given its age and the symptom you describe, I suspect that the tables
are not parallel to each other. One or the other is "drooping".

Usually the outfeed is the one adjusted since it normally doesn't move
once set. If it's on dovetailed ways make sure you have any gib screws
tightened up and see if that helps. You may need to shim it with metal
shim stock.

If it's some sort of parallelogram linkage, then they usually have some
form of eccentric cam adjustment.

Chris