Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
Driving and Car Maintenance: Transportation accounts for 66% of U.S.
oil use -mainly in the form of gasoline. Luckily, there are plenty of ways to improve gas mileage. Driving Tips:- Idling gets you 0 miles per gallon. The best way to warm up a vehicle is to drive it. No more than 30 seconds of idling on winter days is needed. Anything more simply wastes fuel and increases emissions.- Aggressive driving (speeding, rapid acceleration, and hard braking) wastes gas. It can lower your highway gas mileage 33% and city mileage 5%. Drive at lowest and constant rpms; 2000 rpm are enough; you can save up to 30%. Even a Porsche can be driven at the 4th gear at 20 mph and at the 6th gear at 50 mph with 2.5 times less fuel consumption.- Avoid high speeds. Driving 75 mph, rather than 65 mph, could cut your fuel economy by 15%.- When you use overdrive gearing, your cars engine speed goes down. This saves gas and reduces wear.- Use air conditioning only when necessary.- Clear out your car; extra weight decreases gas mileage. Each 60 pounds increases fuel consumption by 10%. - Reduce drag by placing items inside the car or trunk rather than on roof racks. A roof rack or carrier provides additional cargo space and may allow you to buy a smaller car. However, a loaded roof rack can decrease your fuel economy by 5%.- Check into carpooling and public transit to cut mileage and car maintenance costs. Car Maintenance Tips:- Use the grade of motor oil recommended by your cars manufacturer. Using a different motor oil can lower your gasoline mileage by 1% to 2%.- Keep tires properly inflated and aligned to improve your gasoline mileage by around 3.3%.- Get regular engine tune-ups and car maintenance checks to avoid fuel economy problems due to worn spark plugs, dragging brakes, low transmission fluid, or transmission problems.- Replace clogged air filters to improve gas mileage by as much as 10% and protect your engine.- Combine errands into one trip. Several short trips, each one taken from a cold start, can use twice as much fuel as one trip covering the same distance when the engine is warm. Do not forget that in the first mile your car uses 8 times more fuel, in the second mile 4 times and only after the fourth mile it becomes normal.Long-Term Savings Tip- Consider buying a highly fuel-efficient vehicle. A fuelefficient vehicle, a hybrid vehicle, or an alternative fuel vehicle could save you a lot at the gas pump and help the environment.See the Fuel Economy Guide (www.fueleconomy.gov) for more on buying a new fuel-efficient car or truck. Source: www.eere.energy.gov and http://www.vcd.org/155.html |
#2
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
".." wrote in message ... hard braking) wastes gas. Never seen gas powered brakes. |
#3
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
... wrote:
Driving and Car Maintenance: Transportation accounts for 66% of U.S. oil use -mainly in the form of gasoline. Luckily, there are plenty of ways to improve gas mileage. Driving Tips:- Idling gets you 0 miles per gallon. The best way to warm up a vehicle is to drive it. No more than 30 seconds of idling on winter days is needed. Anything more simply wastes fuel and increases emissions.- Aggressive driving (speeding, rapid acceleration, and hard braking) wastes gas. It can lower your highway gas mileage 33% and city mileage 5%. Drive at lowest and constant rpms; 2000 rpm are enough; you can save up to 30%. Even a Porsche can be driven at the 4th gear at 20 mph and at the 6th gear at 50 mph with 2.5 times less fuel consumption.- Avoid high speeds. Driving 75 mph, rather than 65 mph, could cut your fuel economy by 15%.- When you use overdrive gearing, your cars engine speed goes down. This saves gas and reduces wear.- Use air conditioning only when necessary.- Clear out your car; extra weight decreases gas mileage. Each 60 pounds increases fuel consumption by 10%. - Reduce drag by placing items inside the car or trunk rather than on roof racks. A roof rack or carrier provides additional cargo space and may allow you to buy a smaller car. However, a loaded roof rack can decrease your fuel economy by 5%.- Check into carpooling and public transit to cut mileage and car maintenance costs. Car Maintenance Tips:- Use the grade of motor oil recommended by your cars manufacturer. Using a different motor oil can lower your gasoline mileage by 1% to 2%.- Keep tires properly inflated and aligned to improve your gasoline mileage by around 3.3%.- Get regular engine tune-ups and car maintenance checks to avoid fuel economy problems due to worn spark plugs, dragging brakes, low transmission fluid, or transmission problems.- Replace clogged air filters to improve gas mileage by as much as 10% and protect your engine.- Combine errands into one trip. Several short trips, each one taken from a cold start, can use twice as much fuel as one trip covering the same distance when the engine is warm. Do not forget that in the first mile your car uses 8 times more fuel, in the second mile 4 times and only after the fourth mile it becomes normal.Long-Term Savings Tip- Consider buying a highly fuel-efficient vehicle. A fuelefficient vehicle, a hybrid vehicle, or an alternative fuel vehicle could save you a lot at the gas pump and help the environment.See the Fuel Economy Guide (www.fueleconomy.gov) for more on buying a new fuel-efficient car or truck. Source: www.eere.energy.gov and http://www.vcd.org/155.html This advice originated with the government, so you know you can trust it. |
#4
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
On 02/27/2010 03:22 PM, .. wrote:
Driving Tips:- Idling gets you 0 miles per gallon. The best way to warm up a vehicle is to drive it. No more than 30 seconds of idling on winter days is needed. I disagree with this one. At -40 and below, a few more minutes makes the engine note even out and the car feels a lot happier. That said, I also disagree with those that idle for long periods of time...there was a guy across the street that used to idle his truck for half an hour before leaving. The part about driving in 4th gear at 20mph is pushing it a bit...I have a 1.8L engine that doesn't develop peak power until about 6000rpm. Driving anything below 30mph in 4th means its lugging badly. Chris |
#5
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
Chris Friesen wrote in
el: On 02/27/2010 03:22 PM, .. wrote: Driving Tips:- Idling gets you 0 miles per gallon. The best way to warm up a vehicle is to drive it. No more than 30 seconds of idling on winter days is needed. I disagree with this one. At -40 and below, a few more minutes makes the engine note even out and the car feels a lot happier. That said, I also disagree with those that idle for long periods of time...there was a guy across the street that used to idle his truck for half an hour before leaving. Well, to many people around here "winter day" means 20F-40F. Not -40F and colder. ;-) Some cars just feel cold and stiff for the first few minutes unless you do let them run several minutes, even at 20F. Now when you're going to be sitting for several minutes, shut that engine off. Unless something's broke or it's really windy, the average car isn't going to go from 72F to 20F in 20 minutes. The part about driving in 4th gear at 20mph is pushing it a bit...I have a 1.8L engine that doesn't develop peak power until about 6000rpm. Driving anything below 30mph in 4th means its lugging badly. Chris Well... That's really what the overdrive is for. Not below 30mph (I think most cars kick them in around 50-55mph), but to reduce engine RPM at high speed. And actually many engines are supposed to be most efficient running around 3/4 throttle. Puckdropper -- Never teach your apprentice everything you know. |
#6
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
Puckdropper wrote:
Chris Friesen wrote in el: On 02/27/2010 03:22 PM, .. wrote: Driving Tips:- Idling gets you 0 miles per gallon. The best way to warm up a vehicle is to drive it. No more than 30 seconds of idling on winter days is needed. I disagree with this one. At -40 and below, a few more minutes makes the engine note even out and the car feels a lot happier. That said, I also disagree with those that idle for long periods of time...there was a guy across the street that used to idle his truck for half an hour before leaving. Well, to many people around here "winter day" means 20F-40F. Not -40F and colder. ;-) Some cars just feel cold and stiff for the first few minutes unless you do let them run several minutes, even at 20F. Now when you're going to be sitting for several minutes, shut that engine off. Unless something's broke or it's really windy, the average car isn't going to go from 72F to 20F in 20 minutes. The part about driving in 4th gear at 20mph is pushing it a bit...I have a 1.8L engine that doesn't develop peak power until about 6000rpm. Driving anything below 30mph in 4th means its lugging badly. Chris Well... That's really what the overdrive is for. Not below 30mph (I think most cars kick them in around 50-55mph), but to reduce engine RPM at high speed. And actually many engines are supposed to be most efficient running around 3/4 throttle. Puckdropper 3/4 throttle without specifying the gear doesn't mean anything. 3/4 throttle in overdrive gear in my car is probably 130mph, which probably isn't it's most fuel efficient. |
#7
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
"chaniarts" wrote in message ... Well... That's really what the overdrive is for. Not below 30mph (I think most cars kick them in around 50-55mph), but to reduce engine RPM at high speed. And actually many engines are supposed to be most efficient running around 3/4 throttle. Puckdropper 3/4 throttle without specifying the gear doesn't mean anything. 3/4 throttle in overdrive gear in my car is probably 130mph, which probably isn't it's most fuel efficient. The transmission gear is irrelevant when specifying engine efficiency. The engine is more efficient at a throttle plate opening of 1/2 to 3/4. Below this opening the pumping losses around the plate go way up. Above this and the mixture gets richer on carbureted engines, FI may be different. Back in the 70's one of the car mags ran an article on a BMW study of the most efficient acceleration method. The end result was to accelerate at 1/2 throttle opening up to 2,000 rpm and upshift. This is repeated until the desired speed is reached then use the highest gear, without lugging the engine, and the appropriate throttle opening. Their data showed that small throttle openings caused low efficiency, and mpg, due to the high pumping losses. Long sloooow acceleration times were almost as bad a jack rabbit start. Art |
#8
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
"Artemus" wrote in
: "chaniarts" wrote in message ... Well... That's really what the overdrive is for. Not below 30mph (I think most cars kick them in around 50-55mph), but to reduce engine RPM at high speed. And actually many engines are supposed to be most efficient running around 3/4 throttle. Puckdropper 3/4 throttle without specifying the gear doesn't mean anything. 3/4 throttle in overdrive gear in my car is probably 130mph, which probably isn't it's most fuel efficient. The transmission gear is irrelevant when specifying engine efficiency. The engine is more efficient at a throttle plate opening of 1/2 to 3/4. Below this opening the pumping losses around the plate go way up. Above this and the mixture gets richer on carbureted engines, FI may be different. Back in the 70's one of the car mags ran an article on a BMW study of the most efficient acceleration method. The end result was to accelerate at 1/2 throttle opening up to 2,000 rpm and upshift. This is repeated until the desired speed is reached then use the highest gear, without lugging the engine, and the appropriate throttle opening. Their data showed that small throttle openings caused low efficiency, and mpg, due to the high pumping losses. Long sloooow acceleration times were almost as bad a jack rabbit start. Art This has generated bit of research for me. The Wikipedia article on Engine Efficiency says 3/4 horsepower rating (and not 3/4 throttle) would be most efficient, while the Prius article says that the Prius runs the engine with the throttle fully open as much as possible to minimize pumping losses. In a simple system like a hydraulic powered mower, 3/4 throttle could equal 3/4 horsepower output. In something more complex, 3/4 throttle may not be able to produce the 3/4 horsepower output. However, the Wikipedia article on Engine Efficiency could be wrong about 3/4 rated horspower output. That particilar article was rather poorly written and doesn't cite its sources. Puckdropper -- Never teach your apprentice everything you know. |
#9
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
Artemus wrote:
The transmission gear is irrelevant when specifying engine efficiency. The engine is more efficient at a throttle plate opening of 1/2 to 3/4. Below this opening the pumping losses around the plate go way up. Above this and the mixture gets richer on carbureted engines, FI may be different. Fuel injection is indeed much different. Back in the 70's one of the car mags ran an article on a BMW study of the most efficient acceleration method. The end result was to accelerate at 1/2 throttle opening up to 2,000 rpm and upshift. This is repeated until the desired speed is reached then use the highest gear, without lugging the engine, and the appropriate throttle opening. Their data showed that small throttle openings caused low efficiency, and mpg, due to the high pumping losses. Long sloooow acceleration times were almost as bad a jack rabbit start. A lot has changed since then. Even then, that study was limited in scope since it did not consider all of the various engines out there at the time. Today, there are a lot more small DOHC engines out there that run at 6K in order to hit their torque curve, and lot less pushrod v-8's which deliver torque just about off an idle. Not to mention that everything is fuel injected today and nobody manufactures a production carburated engine. About the only thing that hasn't changed is that nobody likes to get stuck behind that guy that believes it's better to accelerate slooooooooly.... -- -Mike- |
#10
Posted to rec.woodworking
|
|||
|
|||
How you can save fuel and the environment
... wrote:
Driving and Car Maintenance: Transportation accounts for 66% of U.S. oil use -mainly in the form of gasoline. Luckily, there are plenty of ways to improve gas mileage. [...] Excellent ideas. Conserving fuel keeps the price down for the rest of us who don't give a fig about saving either fuel or the environment. Everytime I see a fool commuting to work on a bicycle in a business suit, I think to myself "There's another penny a gallon saved!" |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
How you can save fuel and the environment | Electronics Repair | |||
How you can save fuel and the environment | UK diy | |||
How you can save fuel and the environment | Home Repair | |||
How you can save fuel and the environment | Home Repair | |||
How you can save fuel and the environment | Home Ownership |