Cutting 8x8 PT Railroad Ties
 

I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Thanks,

MC

Cutting 8x8 PT Railroad Ties
 

"MiamiCuse" wrote in message
...
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?


Used ties? Get a saw from someone you hate. Or take your garden variety
bowsaw or crosscut and do it. Lots of grit in there, and then there's the
treatment. Neither will make the job easy nor improve the saw.

Cutting 8x8 PT Railroad Ties
 

Hey MC,
I have similar thoughts to George's reply but here is a method for
cutting timbers larger than a saws cutting depth;
Make a fence around the sides of the timber to guide your circular saw
on all four sides. After cutting you will be left with a small nib
that can be cut with a hand saw or recipricating saw. That last cut
won't be perfectly smooth but the edges will look nice. Hold your
breath for each cut! Seriously, wear some type of respiraory
protection. Maybe wet down the area so the dust/chips don't blow
away.
Would your miter saw be able to make a contiguous starter kerf on each
face? If so, that's a simial approach to my first suggestion.
Marc



On Jul 15, 4:48 am, "MiamiCuse" wrote:
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Thanks,

MC

Cutting 8x8 PT Railroad Ties
 

Heh, I cut the tops off a bunch of 4x4's when I built a fence for my
last house. Since the holes were not all dug at exactly the same depth,
I decided to just put all the posts in and when the concrete base dried,
cut the tops off all of them to a standard height. I just made a square
"jig" out of wood and slipped it over the top of the post and screwed it
in at the right height. That served as a clamped edge guide that I ran
my circular saw across all the way around the post. It worked great!
I'll bet my neighbors were wondering what the bleep I was doing, but I
did get great results.

I would do the same for these timbers, but I would probably not subject
any of my saws to that. Assuming these do not have to be precision-cut,
I would go retro and use a bow saw and previously mentioned.

marc rosen wrote:
Hey MC,
I have similar thoughts to George's reply but here is a method for
cutting timbers larger than a saws cutting depth;
Make a fence around the sides of the timber to guide your circular saw
on all four sides. After cutting you will be left with a small nib
that can be cut with a hand saw or recipricating saw. That last cut
won't be perfectly smooth but the edges will look nice. Hold your
breath for each cut! Seriously, wear some type of respiraory
protection. Maybe wet down the area so the dust/chips don't blow
away.
Would your miter saw be able to make a contiguous starter kerf on each
face? If so, that's a simial approach to my first suggestion.
Marc



On Jul 15, 4:48 am, "MiamiCuse" wrote:
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Thanks,

MC

Cutting 8x8 PT Railroad Ties
 

Hire a chain saw and appropriate protective equipment including the kevlar quilted trousers (V.
important). The cut will be OK for rustic garden use.
If you are making fine furniture, you need some different wood.

"MiamiCuse" wrote in message ...
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I need to cut into short,
8"-10" long sections. What is the best way to go about it? I can't use my compound miter saw with
such a large cross section, and I am not sure I can get a clean cut with a circular saw (not with my
skill level). Any suggestions?

Thanks,

MC

Cutting 8x8 PT Railroad Ties
 

In article ,
says...
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Thanks,

MC

Even a small-ish chainsaw will do that without a problem. Hint: mark out top,
front and back to get a nice square cut with a chainsaw.

-P.


--
=========================================
firstname dot lastname at gmail fullstop com

Cutting 8x8 PT Railroad Ties
 

"MiamiCuse" wrote in message
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Among the other suggestions is a portable band saw, which you can rent at
many tool rental centers, or buy for less than $150 if you have frequent
need for one.

--
www.e-woodshop.net
Last update: 6/1/07
KarlC@ (the obvious)

Cutting 8x8 PT Railroad Ties
 

"MiamiCuse" wrote in message
...
I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?


Are these real rail road ties? That is, the type preserved with creosote? If
so be aware that they often have steel embedded in the ends to stop
splitting which presents a hazard when sawing. Also be aware the creosote is
nasty stuff so wear a dust mask and gloves.

On the other hand, if they are just PT (green wood) there is no steel
embedded in the ends but the mask and gloves are still warranted.

How clean a cut do you need for landscaping? I'd be inclined to use a speed
square and circular saw coming in from all four sides and finish it off with
a hand saw. Worst case you can clean the cut up with a sharp chisel.

John

Cutting 8x8 PT Railroad Ties
 

Boy, you guys sure have different experiences with railroad ties
than I do. They eat tools for breakfast and destroy men and
muscle by lunch. These things are full of rocks, sand, grit, and
creosote - none of which lend themselves to anything I want my
tools working on.

The best suggestion to date: Cheap blades in a circular saw,
finished off with a hand bowsaw. Don't plan on many cuts per
blade.
A carbide chainsaw blade at about $70 will give the most cuts, but
is only effective if you are paying for labor. You will destroy a
regular chain in a very few cuts.
A have tried a gasoline cut off saw with a fiber blade which can
take the abuse. Smokes a lot, but actually isn't bad. I've not
ever found what I would call a good solution.

--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)




"MiamiCuse" wrote in message
...
I have six pieces of pressure treated 8"x8" railroad ties (8'
long) that I need to cut into short, 8"-10" long sections. What
is the best way to go about it? I can't use my compound miter
saw with such a large cross section, and I am not sure I can get
a clean cut with a circular saw (not with my skill level). Any
suggestions?

Thanks,

MC

Cutting 8x8 PT Railroad Ties
 

Jim wrote:

I would do the same for these timbers, but I would probably not subject
any of my saws to that. Assuming these do not have to be precision-cut,
I would go retro and use a bow saw and previously mentioned.

Time for a brand new saw blade ... from HF.


--
I'm not not at the above address.
http://nmwoodworks.com


---
avast! Antivirus: Outbound message clean.
Virus Database (VPS): 000756-1, 07/13/2007
Tested on: 7/15/2007 7:22:05 PM
avast! - copyright (c) 1988-2007 ALWIL Software.
http://www.avast.com

Cutting 8x8 PT Railroad Ties
 

In article , says...
Boy, you guys sure have different experiences with railroad ties
than I do. They eat tools for breakfast and destroy men and
muscle by lunch.


Hmmm, when I bought this property I inherited some railroad-tied garden
features with it. Not my style. So I pulled them out and cut them up.
No they didn't eat my tools, but definitely 'yes' to the destroy men and muscle
bit: Aussie hardwood, about as heavy as concrete of the same dimensions it felt
like .... ;-)

It's definitely a good idea to give them a good hosing off first and get dirt,
and stones out and see what else might be in there. I didn't just grab the saw
and start cutting.

-P.

--
=========================================
firstname dot lastname at gmail fullstop com

Cutting 8x8 PT Railroad Ties
 

Peter Huebner wrote:


Hmmm, when I bought this property I inherited some railroad-tied garden
features with it. Not my style.


Many years ago built some flower beds using creosote impregnated
railroad ties and lucky stones.

A hand pruning saw did the job, but I was young and ambitious back thenG.

Lew

Cutting 8x8 PT Railroad Ties
 

On Jul 15, 9:48 am, "DanG" wrote:
Boy, you guys sure have different experiences with railroad ties
than I do. They eat tools for breakfast and destroy men and
muscle by lunch. These things are full of rocks, sand, grit, and
creosote - none of which lend themselves to anything I want my
tools working on.

The best suggestion to date: Cheap blades in a circular saw,
finished off with a hand bowsaw. Don't plan on many cuts per
blade.
A carbide chainsaw blade at about $70 will give the most cuts, but
is only effective if you are paying for labor. You will destroy a
regular chain in a very few cuts.
A have tried a gasoline cut off saw with a fiber blade which can
take the abuse. Smokes a lot, but actually isn't bad. I've not
ever found what I would call a good solution.

--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)


"MiamiCuse" wrote in message

...



I have six pieces of pressure treated 8"x8" railroad ties (8'
long) that I need to cut into short, 8"-10" long sections. What
is the best way to go about it? I can't use my compound miter
saw with such a large cross section, and I am not sure I can get
a clean cut with a circular saw (not with my skill level). Any
suggestions?

Thanks,

MC- Hide quoted text -

- Show quoted text -



These things are full of rocks, sand, grit, and
creosote - none of which lend themselves to anything I want my
tools working on.


And metal...did I say metal?

Any time you start cutting one of these you can expect to find
anything waiting for you...including railroad spikes buried within.

TMT

Cutting 8x8 PT Railroad Ties
 

"Too_Many_Tools" wrote in message
ups.com...
On Jul 15, 9:48 am, "DanG" wrote:
Boy, you guys sure have different experiences with railroad ties
than I do. They eat tools for breakfast and destroy men and
muscle by lunch. These things are full of rocks, sand, grit, and
creosote - none of which lend themselves to anything I want my
tools working on.

The best suggestion to date: Cheap blades in a circular saw,
finished off with a hand bowsaw. Don't plan on many cuts per
blade.
A carbide chainsaw blade at about $70 will give the most cuts, but
is only effective if you are paying for labor. You will destroy a
regular chain in a very few cuts.
A have tried a gasoline cut off saw with a fiber blade which can
take the abuse. Smokes a lot, but actually isn't bad. I've not
ever found what I would call a good solution.

--
______________________________
Keep the whole world singing . . . .
DanG (remove the sevens)


"MiamiCuse" wrote in message

...



I have six pieces of pressure treated 8"x8" railroad ties (8'
long) that I need to cut into short, 8"-10" long sections. What
is the best way to go about it? I can't use my compound miter
saw with such a large cross section, and I am not sure I can get
a clean cut with a circular saw (not with my skill level). Any
suggestions?

Thanks,

MC- Hide quoted text -

- Show quoted text -



These things are full of rocks, sand, grit, and
creosote - none of which lend themselves to anything I want my
tools working on.


And metal...did I say metal?

Any time you start cutting one of these you can expect to find
anything waiting for you...including railroad spikes buried within.

TMT


Many years ago (32 or so) I landscaped with used railroad ties,
loaded with grit, rocks, and such (no spikes). I bought an
electric chain saw with what was called a "baracuda" chain.
Probably spent $99 on the thing. It went thru a significant
number of ties, mostly cut to 3' lengths but with many short
pieces standing tall in the landscape with trunctated tops (45
degree cuts all around with a flat on the top).

ABSOLUTELY no problems! One technique I used was to
put the "rocky side" down so that debris might shake loose.
I didn't intentionally cut into stones, but from time to time
I'd hit one and it didn't damage the chain.

A rough estimate is that I made well over 80 cuts thru the
whole ties, plus untold number of "truncations," all with the
same chain.

Still have the same saw, though don't use it too often. About
five years ago I replaced the original chain.

Oh, and the saw is a Craftsman, bought from Sears.

Jim Stuyck

Cutting 8x8 PT Railroad Ties
 

Build a saddle that |__| fits exactly over the 8x8 and use
that as your edge to cut against with the circular saw.

Finish up with a "hand saw"....(sort of neanderthal) but it
still works....


MiamiCuse wrote:

I have six pieces of pressure treated 8"x8" railroad ties (8' long) that I
need to cut into short, 8"-10" long sections. What is the best way to go
about it? I can't use my compound miter saw with such a large cross
section, and I am not sure I can get a clean cut with a circular saw (not
with my skill level). Any suggestions?

Thanks,

MC