Proper Sandpaper Grit for Sanding Oak Floor
 

What's the highest grit that one uses to finish off sanding an oak floor?
The rental guy said that 120 grit is the highest that people normally go,
and that beyond that there's not "teeth" for the polyurethane. They don't
carry sandpaper for the sanders beyond 120. Hey said Norton didn't make it
any higher (6", no holes).

I just took the floors to 120 ,and they look decent, but I think I'd like
something even smoother.

Appreciate any input.

Proper Sandpaper Grit for Sanding Oak Floor
 

"Buck Turgidson" wrote in message
...
What's the highest grit that one uses to finish off sanding an oak floor?
The rental guy said that 120 grit is the highest that people normally go,
and that beyond that there's not "teeth" for the polyurethane. They don't
carry sandpaper for the sanders beyond 120. Hey said Norton didn't make
it any higher (6", no holes).

I just took the floors to 120 ,and they look decent, but I think I'd like
something even smoother.

Appreciate any input.


You can always make your own using an old flannel shirt, spray on adhesive,
higher grit sandpaper and a hole punch.

Proper Sandpaper Grit for Sanding Oak Floor
 

"Buck Turgidson" wrote in message
...
What's the highest grit that one uses to finish off sanding an oak floor?
The rental guy said that 120 grit is the highest that people normally go,
and that beyond that there's not "teeth" for the polyurethane. They don't
carry sandpaper for the sanders beyond 120. Hey said Norton didn't make
it any higher (6", no holes).

I just took the floors to 120 ,and they look decent, but I think I'd like
something even smoother.

A floor sander is probably a bit brutish for finer paper. The key for
polyurethane issue is nonsense.

If it is good and flat at 120 grit and you want a very fine finish then
hoover up all the dust, give it a good wetting with clean water, let it dry
completely and then sand smooth with 150 grit paper in an orbital sander.
The water will raise the grain, aprocess i don't have time to describe right
now but you will see how it works when you do it.

Tim w

Proper Sandpaper Grit for Sanding Oak Floor
 

Buck Turgidson wrote:

I just took the floors to 120 ,and they look decent, but I think I'd like
something even smoother.

Appreciate any input.



I used 150 grit screens between coats, with a 12"x18" orbital floor sander.

Proper Sandpaper Grit for Sanding Oak Floor
 

"David F. Eisan" wrote in message
I stopped with 80g on my Bosch 1250 6" ROS. Remember, you will always be
5'
away from the finish!

I'm not understanding what you mean by "5' away from the finish". Possibly
you meant 5", but either way, please explain.

Thanks

Proper Sandpaper Grit for Sanding Oak Floor
 

"Upscale" wrote in message
...

"David F. Eisan" wrote in message
I stopped with 80g on my Bosch 1250 6" ROS. Remember, you will always be
5'
away from the finish!

I'm not understanding what you mean by "5' away from the finish".
Possibly
you meant 5", but either way, please explain.

Thanks



I'm pretty sure he means you are not going to be looking at the finish on
your hands and knees--assuming you are of average height, your eyes will be
about 5 feet from the finish.

-Bill

Proper Sandpaper Grit for Sanding Oak Floor
 

Hello there,

I stopped with 80g on my Bosch 1250 6" ROS. Remember, you will always be 5'
away from the finish!

Thanks,

David.

Proper Sandpaper Grit for Sanding Oak Floor
 

I ended up finishing it off with 220 on a pole sander. It only took about
45 minutes, and was a good upper-body workout.

Proper Sandpaper Grit for Sanding Oak Floor
 

Sorry, and I mean this in the nicest way, you guys are nuts. I've had
several floors finished to 100 and 120 and once the high gloss coating is
applied I've found myself sliding along the floor. Are you going to sand
between each coat as well?