Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 63
Default BLO and Thinner

I mixed some blo and thinner in a glass fruit jar. Is it safe to put a tight
lid on this and keep it in a cool dark place or will it build up pressure
and blow up? I think it should be fine but SWMBO isn't so sure.

Thanks
Jimmy


  #2   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 6,375
Default BLO and Thinner

In article , "Jimmy" wrote:
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a tight
lid on this and keep it in a cool dark place or will it build up pressure
and blow up? I think it should be fine but SWMBO isn't so sure.


Sounds fine to me.

--
Regards,
Doug Miller (alphageek at milmac dot com)

It's time to throw all their damned tea in the harbor again.
  #3   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 568
Default BLO and Thinner

On Jan 24, 5:06 pm, "Jimmy" wrote:
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a tight
lid on this and keep it in a cool dark place


Yes, no problem. There isn't anything in there that would react to
form a gas and increase pressure significantly inside the jar.
The only time I can think of that finishes could "blow up" under normal
conditions (without extreme heat, sparks, etc.) is via spontaneous
combustion. This occurs when the finish polymerizes or catalyzes, and
the polymerization builds up heat, and when there's enough heat, some
fuel, and some air, spontaneous combustion can occur. The main way
I've heard of this happening is when a finish-soaked rag is wadded up
and left for a while, especially in a warm area - the rag provides lots
of surface area and possibly some insulation, so the finish can
polymerize quickly and build up heat. As long as the rag is spread
out, the heat can dissipate and it shouldn't be a problem, or I know
that some people submerge used rags in cans of water.
There isn't enough surface area for this to happen in the jar/can - if
anything, you might get a skim of polymerized finish on the surface of
your jar, but I've never heard of spontaneous combustion happening in a
partially-full container.
Good luck,
Andy

  #4   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 526
Default BLO and Thinner

Jimmy wrote:
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a tight
lid on this and keep it in a cool dark place or will it build up pressure
and blow up? I think it should be fine but SWMBO isn't so sure.

Thanks
Jimmy



I cut some BLO with thinner a while back and stored it in an old yeast
bottle - the kind that's tinted dark brown. Not because of the tinting,
but because of the size of the bottle. I can't remember when I did that;
it was in the summer sometime. It's been fine ever since.

Tanus

--
This is not really a sig.
  #5   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 136
Default BLO and Thinner

I keep my BLO + turpentine mixture in an old hand soap dispenser, with the
push down squirt top. If there is any pressure in the bottle, it dribbles
product out the dispenser.

It doesn't.

You're safe.

Old Guy


"Jimmy" wrote in message
t...
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a
tight lid on this and keep it in a cool dark place or will it build up
pressure and blow up? I think it should be fine but SWMBO isn't so sure.

Thanks
Jimmy





  #6   Report Post  
Posted to rec.woodworking
L L is offline
external usenet poster
 
Posts: 18
Default BLO and Thinner

In article ,
Jimmy wrote:
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a tight
lid on this and keep it in a cool dark place or will it build up pressure
and blow up? I think it should be fine but SWMBO isn't so sure.

Thanks
Jimmy



It will be fine until it comes time to remove the cap. Put a piece of
waxed paper or plastic wrap around the jar threads before screwing on
the lid. IME BLO always causes a vacuum inside a container when
stored, not pressure. It will use up and absorb any oxygen in the
container trying to cure.
--
Contentment makes poor men rich. Discontent makes rich men poor.
--Benjamin Franklin

Larry Wasserman - Baltimore Maryland - lwasserm(a)sdf.lonestar.org
  #7   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 63
Default BLO and Thinner

Thanks for the info.
"L" wrote in message
...
In article ,
Jimmy wrote:
I mixed some blo and thinner in a glass fruit jar. Is it safe to put a
tight
lid on this and keep it in a cool dark place or will it build up pressure
and blow up? I think it should be fine but SWMBO isn't so sure.

Thanks
Jimmy



It will be fine until it comes time to remove the cap. Put a piece of
waxed paper or plastic wrap around the jar threads before screwing on
the lid. IME BLO always causes a vacuum inside a container when
stored, not pressure. It will use up and absorb any oxygen in the
container trying to cure.
--
Contentment makes poor men rich. Discontent makes rich men poor.
--Benjamin Franklin

Larry Wasserman - Baltimore Maryland - lwasserm(a)sdf.lonestar.org



Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
BLO Shelf Life Russ Stanton Woodworking 2 January 9th 07 02:34 PM
Watco, BLO and buffing Rob McConachie Woodturning 3 September 5th 05 05:29 PM
BLO question John Moorhead Woodworking 24 April 27th 05 08:57 PM
Rhapsody In BLO Tom Watson Woodworking 14 March 23rd 05 02:41 PM
plywood's getting thinner.... bob Woodworking 29 January 5th 05 05:24 PM


All times are GMT +1. The time now is 05:26 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"