What do I really need to cut trim?
 

Hi,

I would like to install a few stationary panes of glass myself and I'm
dissatisfied with the selections of trim that I find at Home Depot or
Lowes.

What do I need to cut my own window trim?
Would an inexpensive router table be sufficient or would I also need a
planer?
Is there such a thing as a cheap nail gun? I saw an electric version at
HD for $70.
Finally, the panes that I will install first are quite high at 70
inches. What tool do I use to make sure that I'm installing the trim
perfectly straight and that the glass will fit tightly against it?

Many thanks in advance!

Aaron Fude

What do I really need to cut trim?
 

For trim selection or custom manufacture, I suggest that you contact a
cabinet shop. If they don't have trim you like, you can pay for a
custom molding cutter and have them make up a few lengths out of
whatever wood you want to buy.
For finish nailing, it's going to be pneumatic, not electric, and they
are rentable. Typically a 16-guage finish nailer will work and not
leave an oversize hole to fill with putty.
As far as ensuring that the glass is plumb and not cocked in the
opening, simply measuring from the inside wall should make it
sufficiently even on all edges.
Will the glass be insulated (double-paned) glass or just ordinary
window glass?

wrote:
Hi,

I would like to install a few stationary panes of glass myself and I'm
dissatisfied with the selections of trim that I find at Home Depot or
Lowes.

What do I need to cut my own window trim?
Would an inexpensive router table be sufficient or would I also need a
planer?
Is there such a thing as a cheap nail gun? I saw an electric version at
HD for $70.
Finally, the panes that I will install first are quite high at 70
inches. What tool do I use to make sure that I'm installing the trim
perfectly straight and that the glass will fit tightly against it?

Many thanks in advance!

Aaron Fude

What do I really need to cut trim?
 

What do I really need to cut trim?
 

Thanks for all responses!


For finish nailing, it's going to be pneumatic, not electric, and they
are rentable. Typically a 16-guage finish nailer will work and not
leave an oversize hole to fill with putty.

How about something like this:
http://www.homedepot.com/prel80/HDUS...l.0& MID=9876

As far as ensuring that the glass is plumb and not cocked in the
opening, simply measuring from the inside wall should make it
sufficiently even on all edges.

Can you elaborate on this a little? What do you mean by the inside
wall? Right now all I have is a door with a square hole. I'm assuming
I'll have to install the trim on one side, then put in the glass, then
trim on the other side.

What do I really need to cut trim?
 

On 23 Jun 2006 12:32:19 -0700, wrote:

Hi,

I would like to install a few stationary panes of glass myself and I'm
dissatisfied with the selections of trim that I find at Home Depot or
Lowes.

What do I need to cut my own window trim?
Would an inexpensive router table be sufficient or would I also need a
planer?
Is there such a thing as a cheap nail gun? I saw an electric version at
HD for $70.
Finally, the panes that I will install first are quite high at 70
inches. What tool do I use to make sure that I'm installing the trim
perfectly straight and that the glass will fit tightly against it?

Hi Aaron,

Looking at your followup post as well, I've got a better idea of what
you're doing here.

If you take apart a steel door with a glass panel, there are two
pieces of plastic gunk that screw together to hold the glass- I'm
assuming that this is what you're going for.

On that assumption, I'd suggest you buy or borrow a table saw- doesn't
have to be a huge one, just something to do a couple of the steps.
You'll need to get all the stock to the same width, and then cut a
rabbet in each side. One of them will set the into the door, and one
of them will be where the glass fits in. Try and make the pieces so
that they meet in the center of the door for the best hold and least
bowing.

The table saw is also good if you want any grooves or angled planes in
your milled trim. Everything else can be done with a router- you can
rout freehand, buy a cheap table, or use a bit of plywood. It's nice
to make the top out of two layers of plywood, but I got by with a hunk
of 3/4" plywood c-clamped to a bench for quite a while. Use a
straight piece of wood clamped to the table top for a fence and a
featherboard (important when milling trim- don't skip it, or you won't
be happy with the results. It's not just safer, it keeps the cut
consistant)

As far as the nailgun goes, you might want to forget that one.
Nailguns are great for trim, but you're talking about windows. I'd
carefully drill and countersink screws into the trim so that the glass
can be replaced later if it get broken or gets foggy inside. If the
screw heads are an aestectic problem for you, invest in a plug cutter
and cover them up.

This can be a fun project- good luck!

What do I really need to cut trim?
 

On Sat, 24 Jun 2006 16:55:10 GMT, "Lowell Holmes"
wrote:


"Prometheus" wrote in message
.. .

The table saw is also good if you want any grooves or angled planes in
your milled trim. Everything else can be done with a router- you can
rout freehand, buy a cheap table, or use a bit of plywood. It's nice
to make the top out of two layers of plywood, but I got by with a hunk
of 3/4" plywood c-clamped to a bench for quite a while. Use a
straight piece of wood clamped to the table top for a fence and a
featherboard (important when milling trim- don't skip it, or you won't
be happy with the results. It's not just safer, it keeps the cut
consistant)

As far as the nailgun goes, you might want to forget that one.
Nailguns are great for trim, but you're talking about windows. I'd
carefully drill and countersink screws into the trim so that the glass
can be replaced later if it get broken or gets foggy inside. If the
screw heads are an aestectic problem for you, invest in a plug cutter
and cover them up.

This can be a fun project- good luck!


Rout freehand?

Only with a pilot bearing :-)

I figured that went without saying- That'd be a mess if you tried to
freehand an ogee or a bead with a cutter without one. :)