varnish in cold weather
 

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?

varnish in cold weather
 

(Featuring a NEW look)
"dw" wrote in message
news:khHvf.711837$xm3.251798@attbi_s21...
So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?


Because you are going to be applying varnish at a colder temp, the varnish
you apply is going to 'cure' more slowly than at more appropriate temps.
You might be able to circumvent this problem by applying your varnish in
thinner layers by diluting your varnish with mineral spirits. Allow to cure
for 24 hrs and reapply. The thinner layers will cure much easier at the
lower temps than the 'out of the can' concentration. I would FIRST try this
on a piece of scrap wood NOT on your project.
--
Stoutman
http://home.triad.rr.com/brianmeliss...ing_frames.htm

varnish in cold weather
 

On Sat, 07 Jan 2006 04:17:20 GMT, "dw" wrote:

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?

Make an adult decision.

varnish in cold weather
 

fyi... wipe on poly @ 60 degrees takes about 4 days to dry without
being tacky(at least on the project I just finished). I imagine below
55 degrees, the solvent doesn't flash off. Maybe a heat lamp in an
insulated box that is spark proof might work. Wipe on poly's work
great, but best @70 degrees. You can experiment on a piece of scrap
wood, its better than screwing up your hard work.

varnish in cold weather
 

dw wrote:
So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?




Unless you want it to look like crap, then have to do it over when it
warms up.

Now you know why I left the MidWestG.

Lew

varnish in cold weather
 

On Sat, 07 Jan 2006 04:17:20 GMT, "dw" scribbled:

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?

What I often do for glue-ups is to bring the pieces of wood inside to
warm up, glue it up, put it on the bench, plug in a small ceramic
electric heater into a thermostat wired to an extension cord, put it
on the work-bench, put the heater under the bench and cover the whole
thing with a tarp. I don't know if this will work with varnish, but in
the immortal words of the late Paul Radovanic, "If you don't
experiment on scraps, you will experiment on your project."

Alternatively, you could try using shellac which is dissolved in
alcohol and is not harmed by cold. It just will take a little longer
to dry.

Luigi
Replace "nonet" with "yukonomics" for real email address
www.yukonomics.ca/wooddorking/humour.html
www.yukonomics.ca/wooddorking/antifaq.html
http://en.wikipedia.org/wiki/Wikiped...ct_Woodworking

varnish in cold weather
 

"rickluce" wrote in message
ups.com...
fyi... wipe on poly @ 60 degrees takes about 4 days to dry without
being tacky(at least on the project I just finished). I imagine below
55 degrees, the solvent doesn't flash off. Maybe a heat lamp in an
insulated box that is spark proof might work. Wipe on poly's work
great, but best @70 degrees. You can experiment on a piece of scrap
wood, its better than screwing up your hard work.


That's the one. Visqueen tent, light bulbs inside for warm, varnish to your
heart's content.

Warm piece and finish in advance, apply, then return to heated space.

varnish in cold weather
 

I suggest you try some waterborne varnish in the house. The "fumes" are much
less. JG

dw wrote:

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?

varnish in cold weather
 

"dw" wrote in news:khHvf.711837$xm3.251798@attbi_s21:

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my
un-heated garage in the middle of this pretty cold Illinois winter. I
now have a small project I would like to varnish... but the varnish
says not to apply if it's below 55 degrees. My unfinished garage has
no heat, and won't be above 55 degrees for a couple of months. And I
can't varnish in the house because my wife can't handle the fumes.

Do I just have to wait for it to warm up?




Is it insulated? You can get a oil-filled space heater to heat your
garage if you've got power. We've got one in our garage to keep things
warm out there. (It's connected to the house, but not the heating/cooling
system.)

Can you isolate a room of your house? Maybe you can work in there and
keep the house from smelling like varnish and still warm enough to dry.
We've been polyurethaning floor boards in our garage for a shed and
shutting the door keeps the fumes from going all over the house. (It was
apparently an outside door at one time. You may have to consider that.)

Puckdropper
--
www.uncreativelabs.net

Old computers are getting to be a lost art. Here at Uncreative Labs, we
still enjoy using the old computers. Sometimes we want to see how far a
particular system can go, other times we use a stock system to remind
ourselves of what we once had.

To email me directly, send a message to puckdropper (at) fastmail.fm

varnish in cold weather
 

Move to Texas. It was about 75 degrees herei n Dallas today. Unreal!
On second thought, don't let anyone know. This place will look like
California if the word gets out.

Waiting for a Blue Norther!




On Sat, 07 Jan 2006 04:17:20 GMT, "dw" wrote:

So, after wanting to "get into woodworking" for 20 years, I've finally
started dabbling a bit. I endured several cold evenings in my un-heated
garage in the middle of this pretty cold Illinois winter. I now have a
small project I would like to varnish... but the varnish says not to apply
if it's below 55 degrees. My unfinished garage has no heat, and won't be
above 55 degrees for a couple of months. And I can't varnish in the house
because my wife can't handle the fumes.

Do I just have to wait for it to warm up?

varnish in cold weather
 

On Sun, 08 Jan 2006 20:31:35 -0600, Tom Banes wrote:

Move to Texas. It was about 75 degrees herei n Dallas today. Unreal!
On second thought, don't let anyone know. This place will look like
California if the word gets out.

Only until July. Then it will be just us, the cactus, rattlesnakes, scorpions and the armadillos.

varnish in cold weather
 

On Mon, 09 Jan 2006 06:37:31 +0000, Roy wrote:

On Sun, 08 Jan 2006 20:31:35 -0600, Tom Banes wrote:

Move to Texas. It was about 75 degrees herei n Dallas today. Unreal!
On second thought, don't let anyone know. This place will look like
California if the word gets out.

Only until July. Then it will be just us, the cactus, rattlesnakes, scorpions and the armadillos.

Or try Albuquerque. It's been in the 60's during the day
for most of the last three weeks. I spent weekend out
in the shop and backyard building counter tops. In the
sun it was over 65 F. Made it real nice to be working
outside. This place is, unfortunately already being
invaded by Californians, so the secret is out.

DGA

varnish in cold weather
 

dgadams wrote:

Or try Albuquerque. It's been in the 60's during the day
for most of the last three weeks. I spent weekend out
in the shop and backyard building counter tops. In the
sun it was over 65 F. Made it real nice to be working
outside. This place is, unfortunately already being
invaded by Californians, so the secret is out.


When it warms up, let me know.

In the mid 80's today at the old boat yard here in SoCal.

Lew

(A Midwest transplant who will NEVER go back)

varnish in cold weather
 

"Lew Hodgett" wrote in message
nk.net...
In the mid 80's today at the old boat yard here in SoCal.

Lew

(A Midwest transplant who will NEVER go back)

This part of the Midwest is beginning to shut down sawmills and pulp
operations because the yet unfrozen ground won't permit harvesting of
timber.

If you need hardwood, get in before the shortage is accute.

varnish in cold weather
 

Use Shellac and apply with a 'Frenching' pad. It will dry in much
colder temps. because of the alchohol solvent and thinner coats. Also
makes a very fine finish with considerable labor.
Bugs