Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
 
Posts: n/a
Default jointer pad question

Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?

Thanks,

Wes
  #2   Report Post  
 
Posts: n/a
Default

I have a couple of sets of push pads.

One has some medium grit sandpaper glued to it, one has a thin foam
rubber pad and one set has some very fine pins about 1/16-1/8 inch
long.

I also don't normally use a push pad when running material over the
jointer.

  #3   Report Post  
Lowell Holmes
 
Posts: n/a
Default


wrote in message
oups.com...
I have a couple of sets of push pads.

One has some medium grit sandpaper glued to it, one has a thin foam
rubber pad and one set has some very fine pins about 1/16-1/8 inch
long.

I also don't normally use a push pad when running material over the
jointer.

I use a push stick on the jointer. It doesn't slip and as a result, neither
do my hands.
:-)

--
Lowell Holmes


  #4   Report Post  
loutent
 
Posts: n/a
Default

In article ,
wrote:

Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?

Thanks,

Wes


Careful...you could go blind....

Lou
  #6   Report Post  
 
Posts: n/a
Default

Well, you could always use double sided tape OR hotmelt glue to hold a
handle/pushstick attached while running the piece thru the jointer

Or, put some peel and stick sandpaper on the contact surface of the
push stick so the sandpaper gives it some grab


John

On Sun, 02 Oct 2005 15:50:31 -0400, wrote:

Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?

Thanks,

Wes

  #7   Report Post  
SonomaProducts.com
 
Posts: n/a
Default

I typically use gloves with rubber coating. There are lots o' versions.
I use the cheapest ones I can get, they are stanley wool gloves with
the fingers and palms sorta dipped in rubber. Get em at HD.

There are more expensive version with rubber dots on the fingers and
palms.

I use these on jointer and when ripping. Can't beat them in my opinion.
I also use a push stick when ripping if it's less than 3" wide rip.

I must admit the jointed does scare me a bit at times but I make sure I
have clean technique and never in a position where a slip would put me
into the blades..

  #8   Report Post  
Doug Miller
 
Posts: n/a
Default

In article .com, "SonomaProducts.com" wrote:
I typically use gloves with rubber coating. There are lots o' versions.
I use the cheapest ones I can get, they are stanley wool gloves with
the fingers and palms sorta dipped in rubber. Get em at HD.


Wearing gloves around any machinery is dumb, dumb, dumb. Use push blocks or
push sticks instead -- the last thing you need is to get the glove snagged by
a spinning tooth or knive, and pull your hand into the cutter.

--
Regards,
Doug Miller (alphageek at milmac dot com)

It's time to throw all their damned tea in the harbor again.
  #9   Report Post  
BobS
 
Posts: n/a
Default

Wes,

Try cleaning them with rubbing alcohol or even mineral spirits and see if
that helps. That's the suggested method for cleaning the rubber rollers on
a DeWalt planer and should not hurt the pads. If they still slip, try
pulling them across a sheet of sandpaper to scuff the surface a bit.

The there's always the "throw more money at it" route - GRR-Rippers

http://www.leevalley.com/wood/page.a...080,51225&ap=1

Bob S.


wrote in message
...
Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?

Thanks,

Wes



  #11   Report Post  
Sam the Cat
 
Posts: n/a
Default

maybe you need to work on the other end of the problem -- have you waxed
your jointer lately. Force needed to push wood across the blade goes down
significantly with a slick jointer bed


wrote in message
...
Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?

Thanks,

Wes



  #12   Report Post  
George
 
Posts: n/a
Default


wrote in message
...
Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?


Imagine a plane with a slight heel. A push block which allows you to
maintain all the pressure at the feed end that you need, and can't slip,
because the heel has hooked the trailing edge. Both hands holding means
none to be jointed....

Great at the table saw too, but always a bit taller as the blades come
through the piece.


  #13   Report Post  
Doug Miller
 
Posts: n/a
Default

In article , "George" George@least wrote:

wrote in message
...
Last night I was trying to put a flat surface on a box end I was
making but when I tried to run the wood across my jointer, my push
pads kept slipping which made it hard to keep my work against my
cutter head.

Anyone have ideas of what I could use to get a sticker grip so I don't
loose my grip on the wood I'm trying to joint?


Imagine a plane with a slight heel. A push block which allows you to
maintain all the pressure at the feed end that you need, and can't slip,
because the heel has hooked the trailing edge. Both hands holding means
none to be jointed....


Great idea for a table saw, as you noted. Not-so-great idea for a jointer,
though, because it necessarily places the feed pressure on the infeed side of
the cutterhead. Feed pressure should be on the infeed side only until enough
wood has passed the cutterhead to enable a safe grip on the outfeed side;
after that, all pressure should be on the outfeed table.

--
Regards,
Doug Miller (alphageek at milmac dot com)

It's time to throw all their damned tea in the harbor again.
  #14   Report Post  
 
Posts: n/a
Default

"Sam the Cat" wrote:

maybe you need to work on the other end of the problem -- have you waxed
your jointer lately. Force needed to push wood across the blade goes down
significantly with a slick jointer bed


That might be a good idea. I'll get the floor wax out this evening and
do that.

Wes
--
Reply to:
Whiskey Echo Sierra Sierra AT Alpha Charlie Echo Golf Romeo Oscar Paul dot Charlie Charlie
Lycos address is a spam trap.
  #15   Report Post  
Toller
 
Posts: n/a
Default

I use one plain pad in the front, and something with a hook on it in the
back.
http://www.wood-worker.com/tips/push-stick.htm

There is nothing special about these; it is just the first site I found on a
search.




  #16   Report Post  
George
 
Posts: n/a
Default


"Doug Miller" wrote in message
.. .
Imagine a plane with a slight heel. A push block which allows you to
maintain all the pressure at the feed end that you need, and can't slip,
because the heel has hooked the trailing edge. Both hands holding means
none to be jointed....


Great idea for a table saw, as you noted. Not-so-great idea for a jointer,
though, because it necessarily places the feed pressure on the infeed side
of
the cutterhead. Feed pressure should be on the infeed side only until
enough
wood has passed the cutterhead to enable a safe grip on the outfeed side;
after that, all pressure should be on the outfeed table.


Press with the forward hand. You have two still? Works great.

On pieces much longer than the push, another will take care of the lead, the
second the trail.


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Tip for 6" Jet Jointer Shoppers in Southern Cal. [email protected] Woodworking 0 June 22nd 05 11:09 AM
Jointer Question Gerald Lasco Woodworking 21 June 20th 05 11:55 PM
jointer question Vic Baron Woodworking 11 May 25th 05 08:20 PM
New DJ-20 jointer arrived today - defect noted Electric Stu Woodworking 16 April 23rd 05 04:14 PM
Soon I will have Jointer Joy Dave Miller Woodworking 10 March 18th 05 04:29 PM


All times are GMT +1. The time now is 03:07 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"