Plasma TV Stand #1
 

Plasma TV Stand #1
 

mcgyver wrote:



Very nice.


--
If you're going to be dumb, you better be tough

Plasma TV Stand #1
 

Very nice. Some questions...

How did you acheive the curves on the legs? Did you use a bandsaw, etc.?

What kind of hardware did you use on the top two doors?

I presume that the plasma TV is going to be bigger than the toshiba
currently sitting on the stand, right?

Plasma TV Stand #1
 

In article 8ngyj.28799$w94.20517@pd7urf2no,
"mcgyver" wrote:

begin 666 Picture 102 resized.jpg
[Image]

end

Wonderful to see what can be done in an afternoon, eh? :-)

I kid.

Looks great!

r

Plasma TV Stand #1
 

Lee, curves were cut on a bandsaw then cleaned up with a template and bit on
the router table, minimal sanding and reproducable.
Hardware is from here
http://www.leevalley.com/hardware/pa...614,43625&ap=1

Yes, the 50"er will be a bit bigger than the 27" sitting on there.;-)

thanks for your comments



"Lee Michaels" wrote in message
. ..
Very nice. Some questions...

How did you acheive the curves on the legs? Did you use a bandsaw, etc.?

What kind of hardware did you use on the top two doors?

I presume that the plasma TV is going to be bigger than the toshiba
currently sitting on the stand, right?

Plasma TV Stand #1
 

Figure i have about ~30 hours or so into it, $300 in materials and hardware.
what would this be worth on the custom market? Not that i will ever sell
it...just want to justify what my times worth..... Thanks
"Robatoy" wrote in message
...
In article 8ngyj.28799$w94.20517@pd7urf2no,
"mcgyver" wrote:

begin 666 Picture 102 resized.jpg
[Image]

end

Wonderful to see what can be done in an afternoon, eh? :-)

I kid.

Looks great!

r

Plasma TV Stand #1
 

Nice - simple, clean lines that look elegant and well suited for the
purpose.

What are the dark "dots" that I see where each shelf mates with the vertical
side pieces? Some kind of pegged joint?

I am designing a piece of my own for a similar purpose. What accommodations
did you make for cables?

How about ventilation? Do you open it up when in use?

Plasma TV Stand #1
 

Robert,

Those dark marks are a "faux" 1/4" pyramided dark walnut pegged joint. the
actual face frame is put together with pocket screws. Cables are through a
1" slot in the back of the cabinet, hardley seen. yes, almost always open,
because the whole top shelf does not have a divider there is a lot of open
space where the components are.
Thanks for the comments


"Robert Haar" wrote in message
...
Nice - simple, clean lines that look elegant and well suited for the
purpose.

What are the dark "dots" that I see where each shelf mates with the
vertical
side pieces? Some kind of pegged joint?

I am designing a piece of my own for a similar purpose. What
accommodations
did you make for cables?

How about ventilation? Do you open it up when in use?

Plasma TV Stand #1
 

mcgyver wrote:

Figure i have about ~30 hours or so into it, $300 in materials and
hardware.

Wow, just 30 hours; that is impressive.


what would this be worth on the custom market? Not that i will ever sell
it...just want to justify what my times worth..... Thanks
"Robatoy" wrote in message
...
In article 8ngyj.28799$w94.20517@pd7urf2no,
"mcgyver" wrote:

begin 666 Picture 102 resized.jpg
[Image]

end

Wonderful to see what can be done in an afternoon, eh? :-)

I kid.

Looks great!

r

--
If you're going to be dumb, you better be tough

Plasma TV Stand #1
 

Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.

Plasma TV Stand #1
 

Nope, no plans, knew the basic size i needed and adapted as i went......
"Casper" wrote in message
...
Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.

Plasma TV Stand #1
 

Can someone repost this image? I'd like to see it.




"Casper" wrote in message
...
Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.

Plasma TV Stand #1 (0/1)
 

Here you go.
Anders


\

\On Tue, 11 Mar 2008 03:16:04 GMT, "Soby1" wrote:

Can someone repost this image? I'd like to see it.




"Casper" wrote in message
.. .
Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.

Plasma TV Stand #1 (1/1)
 

Plasma TV Stand #1 (0/1)
 

That's not a plasma TV....

wrote:
Here you go.
Anders


\

\On Tue, 11 Mar 2008 03:16:04 GMT, "Soby1" wrote:

Can someone repost this image? I'd like to see it.




"Casper" wrote in message
...
Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.

Plasma TV Stand #1 (0/1)
 

It's not even a TV stand made of plasma... What a big fibber! :-)

mapdude wrote:
That's not a plasma TV....

wrote:
Here you go.
Anders


\

\On Tue, 11 Mar 2008 03:16:04 GMT, "Soby1" wrote:

Can someone repost this image? I'd like to see it.




"Casper" wrote in message
...
Beautiful piece. Did you go by plans?
I'm a sucker for this style of stuff.