Woodturning - Page 2

Thread / Thread Starter	Last Post	Replies	Views
D'oh.....(I cant be on my own) Michael Lehmann	by Paul Griffiths	34	718
Is anyone familiar with this chainsaw? [email protected]	by Barry N. Turner	34	1,023
Shipping and Handling Charges? [email protected]	by [email protected]	34	894
Lucubrating on historical value of turning Owen Lowe	by Ray Sandusky	33	1,050
Wooden Knitting Needles Tanus	by Dave Balderstone	33	1,547
rolling pin Gary & Karen	by mac davis	33	933
Exploiting carbide for hollowing cad	by Prometheus	33	1,280
how many use glue blocks william kossack	by Kevin Miller	33	1,702
What kind of sharpening system to buy? Mike Rinken	by George Saridakis	32	1,296
Tool Steel K	by lionslair at consolidated dot net	32	1,244
Nova 3K George	by Chuck	32	1,309
Politically incorrect but honest Tom Nie	by Ken Moon	32	1,073
do you use a sharpening jig??? Graeme :\)	by Graeme :\)	32	1,144
Mutant Bowl Greg G.	by Greg G.	32	838
Which Midi lathe? [email protected]	by charlieb	32	1,337
Faceplate? Jesse	by dan cordes	32	1,386
Best way to cut vertical slots through round posts? Wood Guy	by Bill Noble[_2_]	32	2,268
Beginner Questions Ed Peddycoart	by Rob McConachie	31	1,181
Alcohol Drying of Wet Wood Fred Holder	by Tom Nie	31	2,318
A commercial message -- a new product Bill Rubenstein	by Darrell Feltmate	31	938
How High Should a Lathe Be? Douglas Johnson[_2_]	by Prometheus	31	1,168
jig for cutting blanks on a table saw william kossack	by william kossack	31	1,054
more newbie observations Vic Baron	by Mac Davis	31	1,970
damn, a bandsaw! mac davis	by mac davis	31	1,178
looking for a lathe Reyd Dorakeen	by Reyd Dorakeen	31	1,049
Easy And Nice Finish Wood Turn It Dont Burn It	by AHilton	31	1,653
bevel angle Michael Lehmann	by Ken Moon	30	1,486
How do you interest your wife in woodturning? T. Dougall	by bf	30	698
Stubbys are back Bill Rubenstein	by Barry N. Turner	30	926
Musing if turning well is a lack of failure or a hope for glory. Arch	by mac davis	30	874
An odd project- suggestions greatly appreciated Prometheus	by Dan Bollinger	30	1,100
Boiling? Maxprop	by Chuck	30	1,099
Getting a handle on our tools Arch	by Tom Nie	30	779
Ways and Means Gerald Ross	by Lobby Dosser	30	1,052
Useless musings before falling asleep Arch	by W Canaday	30	839
Talon chuck Bill Gooch	by W Canaday	30	819
Which Bowl Gouge To Buy? skidog	by Greg Lyman	30	2,964
NiChrome questions Bill Stock	by Dan Bollinger	30	1,185
what lathe for $600.00? oldno7	by George	30	938
Glow vs Gloss. Do most people prefer shiny bowls? Arch	by mac davis	29	971
avoiding warp in wet turned bowls william kossack	by Owen Lowe	29	1,472
grinding wheel Leetollett	by Owen Lowe	29	1,030
Chainsaw oil Bill R	by Bill	29	1,312
Suggested wood for carving mallets? mac davis[_5_]	by mac davis[_5_]	29	1,395
Carbide bandsaw blades massmans	by Prometheus	29	734
What is best lathe manufacturer? Rob McConachie	by CJH	29	2,620
I'm done turning for a while william kossack	by Gasser	29	848
Stuck 2-3 Morse taper adapter Phisherman	by Leo Van Der Loo	29	1,194
Allergic Reaction to Cocobolo Barry N. Turner	by Martin H. Eastburn	29	1,355
Moisture Content Meter? Dan Bollinger	by George	29	750
purpleheart Jeff	by Chuck	29	839
Turning Bowels Mark Russell	by mac davis	29	810
Aztec/Maya and the lathe? Denis Marier	by Spyda Man	29	651
sorta newbie question on turning small jars/boxes mac davis	by William Noble	29	956
Skew Chisel Fustration Paul Kierstead	by George	29	1,151
Followup On Problems with Oneway 2436 Paul Rasmussen	by hedgehog	29	1,378
My new website. Gerard	by Prometheus	28	838
Drilling with Forstner Bit Derek Hartzell	by Owen Lowe	28	893
Musing about corks, old friends and olive branches Arch	by George	28	713
what is a fender washer? [email protected]	by Jim Gott	28	993
Toxic wood Stephen	by Maxprop	28	1,030
Anyone here tried to dry wood with the rack in a clothes dryer? Lyndell Thompson	by Owen Lowe	28	1,136
Glue Block vrs. Chuck Paul Kierstead	by Paul Kierstead	28	649
a project from my wife william kossack	by william kossack	28	819
End grain - wet or dry wood Olebiker	by cad	28	1,071
OT question re printer ink Arch	by CW	28	822
How long does it take? Darrell Feltmate	by W Canaday	28	791
pen turning observation Bill in Detroit	by BillR	28	821
Ping Mac Davis ! Shopsmith arbor diameterG. Lyndell Thompson	by Lobby Dosser	28	808
Left-Handed Turning Alan Van Art	by Alun Saunders	27	928
Need advice from woodworking guys Janice Brown	by rj	27	943
A couple of hollowing questions Prometheus	by mac davis	27	900
? Howto: Buy a Stubby from Australia Bjarte Runderheim	by HansNL	27	1,200
attaching a label to a turning william kossack	by JimR[_2_]	27	653
question on grinder speeds Walker	by Mike Paulson	27	1,290