|
Fundamentals Topics
Hey folks,
I was asked, several months ago, if I would present the 30 minute "Fundamentals" portion of my turning club's monthly meeting. I accepted the challenge, and am not averse to talking, presenting and sharing what I know. However, I've pretty much exhausted my very modest store of turning knowledge over the past months. At least that which fits neatly into a "package." Like finishes, holding wood, drying techniques, easy Christmas ornament/box/baby rattle, easy stick pens, etc. I have about 4 weeks to come up with another topic (other than sharpening!!) that I haven't covered, and am at somewhat of a loss. Any suggestions would be helpful and welcome. Bear in mind that I have 30 minutes, and while our turners run the complete spectrum of experience, the session is targeted at the utter beginners, to help introduce them to woodturning in a gentle manner. TIA for your help. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget ----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Fundamentals Topics
Chuck wrote:
Hey folks, I was asked, several months ago, if I would present the 30 minute "Fundamentals" portion of my turning club's monthly meeting. I accepted the challenge, and am not averse to talking, presenting and sharing what I know. However, I've pretty much exhausted my very modest store of turning knowledge over the past months. At least that which fits neatly into a "package." Like finishes, holding wood, drying techniques, easy Christmas ornament/box/baby rattle, easy stick pens, etc. I have about 4 weeks to come up with another topic (other than sharpening!!) that I haven't covered, and am at somewhat of a loss. Any suggestions would be helpful and welcome. Talk about hardware-- Different drives, types of tool rests, Hollow quills, chucks, faceplates, spurs, woodworms etc., giving the goods and bads about them all. For instance I hated my reeves drive when I used regular belts. It chewed them up and spit them out. With a link belt the lathe has hummed quietly along for months. Or take them through the steps from a log to a bowl, with emphasis on why you do what and what the alternatives are. -- Gerald Ross Cochran, GA Guns don't kill people, postal workers do. ----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Fundamentals Topics
"Chuck" wrote in message ... Hey folks, I was asked, several months ago, if I would present the 30 minute "Fundamentals" portion of my turning club's monthly meeting. I accepted the challenge, and am not averse to talking, presenting and sharing what I know. However, I've pretty much exhausted my very modest store of turning knowledge over the past months. At least that which fits neatly into a "package." Like finishes, holding wood, drying techniques, easy Christmas ornament/box/baby rattle, easy stick pens, etc. I have about 4 weeks to come up with another topic (other than sharpening!!) that I haven't covered, and am at somewhat of a loss. Any suggestions would be helpful and welcome. Bear in mind that I have 30 minutes, and while our turners run the complete spectrum of experience, the session is targeted at the utter beginners, to help introduce them to woodturning in a gentle manner. Wood. That's fundamental. Get the free information from the FPL site, some cupped and warped 2X lumber at the Borg to show them how wood moves just like the included diagrams in drying, depending on where it came from in the log. Take some firewood chunks and show them what happens when the bark's on, remind them what happens with it off, and show them those radial checks the last rain storm closed up that are now waiting to ruin their day. While you're at it, discuss the more rapid drying rate of end versus face grain. Both ends of your firewood chunk are examples. Then show a couple of bowl blanks that are dry or drying. Have your tape there to show how the tale of the 2X is repeated, take the rate of shrink and compare it to the old 10% rule, then to the anticipated average shrinkage in the FPL tables and remind them that the inverse square rule applies to a molecule of water attempting to leave a piece of wood, too, so thinner is a winning way to go. Be prepared for soakers and coaters and other naysayers. Cut a 1/2" thick piece off the end of one of those cupped Borg boards and submerge it at the beginning of the half hour. Use it at the end to show what soaking does. |
Fundamentals Topics
Well one topic that I have not seen suggested is safety and safety equipment
and how important that is. Steven Raphael Ithaca MI http://www.geocities.com/steven_raph...turnings1.html "Chuck" wrote in message ... Hey folks, I was asked, several months ago, if I would present the 30 minute "Fundamentals" portion of my turning club's monthly meeting. I accepted the challenge, and am not averse to talking, presenting and sharing what I know. However, I've pretty much exhausted my very modest store of turning knowledge over the past months. At least that which fits neatly into a "package." Like finishes, holding wood, drying techniques, easy Christmas ornament/box/baby rattle, easy stick pens, etc. I have about 4 weeks to come up with another topic (other than sharpening!!) that I haven't covered, and am at somewhat of a loss. Any suggestions would be helpful and welcome. Bear in mind that I have 30 minutes, and while our turners run the complete spectrum of experience, the session is targeted at the utter beginners, to help introduce them to woodturning in a gentle manner. TIA for your help. -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget ----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Fundamentals Topics
Hi Chuck,
You might want to consider warning about 'turning fundamentals' that don't work. ex: ****************************************** long files for scrapers, leaving the chuck key in, forgetting to unlock the indexing pin, suddenly stopping a heavy blank that's not well secured, spinning it suddenly in reverse, starting it with the rpm you left when last used on a miniature, starting a cut by waving the tool about the toolrest. flapping elbows while turning, letting fingers stray away from their side of the toolrest, allowing electricity to return to mother earth thru the turner, etc. etc. You could call your program "Negative Fundamentals" or "A half hour of Novice Blunders", then ask Old Timers to add _their recent blunders. On second thought, these 'fundamentals' are not gentle and much too dangerous for you to demonstrate. Maybe we should all just list ours here, instead. :) Whatever topic you choose, we know your presentation will be useful as well as entertaining for all. Turn to Safety, Arch Fortiter http://community.webtv.net/almcc/MacsMusings |
Fundamentals Topics
On Fri, 7 Apr 2006 11:57:02 -0400, (Arch) wrote:
Hi Chuck, You might want to consider warning about 'turning fundamentals' that don't work. ex: ****************************************** long files for scrapers, leaving the chuck key in, forgetting to unlock the indexing pin, suddenly stopping a heavy blank that's not well secured, spinning it suddenly in reverse, starting it with the rpm you left when last used on a miniature, starting a cut by waving the tool about the toolrest. flapping elbows while turning, letting fingers stray away from their side of the toolrest, allowing electricity to return to mother earth thru the turner, etc. etc. You could call your program "Negative Fundamentals" or "A half hour of Novice Blunders", then ask Old Timers to add _their recent blunders. On second thought, these 'fundamentals' are not gentle and much too dangerous for you to demonstrate. Maybe we should all just list ours here, instead. :) Whatever topic you choose, we know your presentation will be useful as well as entertaining for all. Turn to Safety, Arch Fortiter http://community.webtv.net/almcc/MacsMusings Or, in my case, not checking the speed before starting and realizing that the last thing the lathe was used for was buffing at 1,900 rpm... Makes that first few seconds real exciting.. *g* Mac https://home.comcast.net/~mac.davis https://home.comcast.net/~mac.davis/wood_stuff.htm |
Fundamentals Topics
On Fri, 07 Apr 2006 00:33:39 GMT, (Chuck)
wrote: Thanks all, for the suggestions. I have had several people suggest the safety lecture. Dead boring, but probably a good idea. I've no doubt that some of these ideas will show up in future Fundamentals sessions. Particularly the dangers of turning on your lathe with a 40 lb blank on it at 3000 RPM because the last thing you were doing was making pens.....Mac. ; ) -- Chuck *#:^) chaz3913(AT)yahoo(DOT)com Anti-spam sig: please remove "NO SPAM" from e-mail address to reply. September 11, 2001 - Never Forget ----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Fundamentals Topics
On Wed, 12 Apr 2006 01:31:39 GMT, (Chuck) wrote:
On Fri, 07 Apr 2006 00:33:39 GMT, (Chuck) wrote: Thanks all, for the suggestions. I have had several people suggest the safety lecture. Dead boring, but probably a good idea. I've no doubt that some of these ideas will show up in future Fundamentals sessions. Particularly the dangers of turning on your lathe with a 40 lb blank on it at 3000 RPM because the last thing you were doing was making pens.....Mac. ; ) no, Chuck.. you're the one that turns pens at 2,500... I'm usually at 1,100 or so... As to safety... the guy that did the skew demo at our last meeting was showing the advantage of rounding back the point and heel by CAUSING catches with different grinds... Scared the hell out of me, but he's a retired shop teacher and I checked.. he has all of his fingers.. Mac https://home.comcast.net/~mac.davis https://home.comcast.net/~mac.davis/wood_stuff.htm |
| All times are GMT +1. The time now is 11:50 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter