Treadmill motor wiring diagram & testing procedures
Guys, my Jet Mini with a shop-installed but Jet supplied treadmill motor
took a tumble. Now it won't run. I have looked for obvious things like loose wires, broken connections, cracked circuit board, etc. but do not find anything. Looking at it didn't fix it either--don't laugh, it has worked before!! So if anyone has wiring diagrams and/or testing procedures, I would be grateful for that info. Nearest repair shop is 2 hrs away, $75 minimum charge, 10 day backlog. Would really like to fix it myself if possible, since Jet sold out of these motors a long time ago. Thanks, James Johnson |
ok, try this - I presume you have a DC brush motor? if yes
1. apply DC power to the motor - a car battery will do - does it run? 2. check circuit board for cracks - almost guaranteed 3. power up circuit board/motor (away from lathe) verify AC power at input, verify no DC at output 4. check SCR - anything at the output? (if no then 5. check gate drive - use a scope, that's easist - see if you have any kind of gate drive that looks reasonable (2 or 3 volt pulses) "JRJohnson" wrote in message .. . Guys, my Jet Mini with a shop-installed but Jet supplied treadmill motor took a tumble. Now it won't run. I have looked for obvious things like loose wires, broken connections, cracked circuit board, etc. but do not find anything. Looking at it didn't fix it either--don't laugh, it has worked before!! So if anyone has wiring diagrams and/or testing procedures, I would be grateful for that info. Nearest repair shop is 2 hrs away, $75 minimum charge, 10 day backlog. Would really like to fix it myself if possible, since Jet sold out of these motors a long time ago. Thanks, James Johnson |
I can do that, except checking the gate drive. No scope. But the rest is
easy. Thanks, I appreciate it. James Johnson "william_b_noble" wrote in message news:1121216044.ca8936c9cfcd2e2c99ec4e86fea49a94@t eranews... ok, try this - I presume you have a DC brush motor? if yes 1. apply DC power to the motor - a car battery will do - does it run? 2. check circuit board for cracks - almost guaranteed 3. power up circuit board/motor (away from lathe) verify AC power at input, verify no DC at output 4. check SCR - anything at the output? (if no then 5. check gate drive - use a scope, that's easist - see if you have any kind of gate drive that looks reasonable (2 or 3 volt pulses) "JRJohnson" wrote in message .. . Guys, my Jet Mini with a shop-installed but Jet supplied treadmill motor took a tumble. Now it won't run. I have looked for obvious things like loose wires, broken connections, cracked circuit board, etc. but do not find anything. Looking at it didn't fix it either--don't laugh, it has worked before!! So if anyone has wiring diagrams and/or testing procedures, I would be grateful for that info. Nearest repair shop is 2 hrs away, $75 minimum charge, 10 day backlog. Would really like to fix it myself if possible, since Jet sold out of these motors a long time ago. Thanks, James Johnson |
ok, report results and we'll take it from there.
"JRJohnson" wrote in message ... I can do that, except checking the gate drive. No scope. But the rest is easy. Thanks, I appreciate it. James Johnson "william_b_noble" wrote in message news:1121216044.ca8936c9cfcd2e2c99ec4e86fea49a94@t eranews... ok, try this - I presume you have a DC brush motor? if yes 1. apply DC power to the motor - a car battery will do - does it run? 2. check circuit board for cracks - almost guaranteed 3. power up circuit board/motor (away from lathe) verify AC power at input, verify no DC at output 4. check SCR - anything at the output? (if no then 5. check gate drive - use a scope, that's easist - see if you have any kind of gate drive that looks reasonable (2 or 3 volt pulses) "JRJohnson" wrote in message .. . Guys, my Jet Mini with a shop-installed but Jet supplied treadmill motor took a tumble. Now it won't run. I have looked for obvious things like loose wires, broken connections, cracked circuit board, etc. but do not find anything. Looking at it didn't fix it either--don't laugh, it has worked before!! So if anyone has wiring diagrams and/or testing procedures, I would be grateful for that info. Nearest repair shop is 2 hrs away, $75 minimum charge, 10 day backlog. Would really like to fix it myself if possible, since Jet sold out of these motors a long time ago. Thanks, James Johnson |
All times are GMT +1. The time now is 11:14 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter