How do I replace Euro-lock cylinder
 

I caught a sneak-in burglar on Sunday morning and I think he is away
with a key to the front door.
I will need to change all exterior locks. The doors are Everest UPVC
(not my choice or money) with multi-point locking system. The cylinders
are 40-40 or 40-35.
After removing the handles and key plate to gain access to the cylinder
I have been unable to get the cylinder out. Looking at the euro-lock
cylinders in ironmongers I could see a catch which in the ironmongers is
easy to retract but I cant do this in the door. There is a very thin gap
between the cylinder and the metalwork of the lock which surrounds it
and ?I have tried fuse-wire, a scalpel to retract the pin so I can pull
out the cylinder.
How is it done?
Is there a special joiners/locksmiths tool for this?

--
Z
Remove all Zeds in e-mail address to reply.

How do I replace Euro-lock cylinder
 

On Fri, 11 Jun 2004 17:52:50 +0100, Z wrote:


I caught a sneak-in burglar on Sunday morning and I think he is away
with a key to the front door.
I will need to change all exterior locks. The doors are Everest UPVC
(not my choice or money) with multi-point locking system. The cylinders
are 40-40 or 40-35.
After removing the handles and key plate to gain access to the cylinder
I have been unable to get the cylinder out. Looking at the euro-lock
cylinders in ironmongers I could see a catch which in the ironmongers is
easy to retract but I cant do this in the door. There is a very thin gap
between the cylinder and the metalwork of the lock which surrounds it
and ?I have tried fuse-wire, a scalpel to retract the pin so I can pull
out the cylinder.
How is it done?
Is there a special joiners/locksmiths tool for this?


There is a bolt which goes through the door edge side of the lock into
the cylinder.

You need to undo this, and then turn the lock with the key and you
will find an internal cam will line up and the cylinder will slide
out.


..andy

To email, substitute .nospam with .gl

How do I replace Euro-lock cylinder
 

On Fri, 11 Jun 2004 17:52:50 +0100, Z wrote:


I caught a sneak-in burglar on Sunday morning and I think he is away
with a key to the front door.
I will need to change all exterior locks. The doors are Everest UPVC
(not my choice or money) with multi-point locking system. The cylinders
are 40-40 or 40-35.
After removing the handles and key plate to gain access to the cylinder
I have been unable to get the cylinder out. Looking at the euro-lock
cylinders in ironmongers I could see a catch which in the ironmongers is
easy to retract but I cant do this in the door. There is a very thin gap
between the cylinder and the metalwork of the lock which surrounds it
and ?I have tried fuse-wire, a scalpel to retract the pin so I can pull
out the cylinder.
How is it done?
Is there a special joiners/locksmiths tool for this?


There is a screw in the edge of the door, remove it.
Then the cylinder should be free, and you will feel it loose.
now its just a matter of having the key in the right position to
remove the cylinder by pulling gently on the key.

Rick

How do I replace Euro-lock cylinder
 

"Andy Hall" wrote in message
...
There is a bolt which goes through the door edge side of the lock into
the cylinder.

You need to undo this, and then turn the lock with the key and you
will find an internal cam will line up and the cylinder will slide
out.

My "Multi Locks" have a brass plate which covers the head of the bolt that Andy
refers to. The brass plate is held by screws at top and bottom.

Michael Chare

How do I replace Euro-lock cylinder
 

On Fri, 11 Jun 2004 17:58:23 +0100, Andy Hall wrote:

On Fri, 11 Jun 2004 17:52:50 +0100, Z wrote:


I caught a sneak-in burglar on Sunday morning and I think he is away
with a key to the front door.
I will need to change all exterior locks. The doors are Everest UPVC
(not my choice or money) with multi-point locking system. The cylinders
are 40-40 or 40-35.
After removing the handles and key plate to gain access to the cylinder
I have been unable to get the cylinder out. Looking at the euro-lock
cylinders in ironmongers I could see a catch which in the ironmongers is
easy to retract but I cant do this in the door. There is a very thin gap
between the cylinder and the metalwork of the lock which surrounds it
and ?I have tried fuse-wire, a scalpel to retract the pin so I can pull
out the cylinder.
How is it done?
Is there a special joiners/locksmiths tool for this?


There is a bolt which goes through the door edge side of the lock into
the cylinder.

You need to undo this, and then turn the lock with the key and you
will find an internal cam will line up and the cylinder will slide
out.


This bolt usually has a PHILLIPS not a POSIDRIVE head also it is really
quite frozen. You need to take the undoing of it seriously you only have
one chance. Also you do not want to shear this bolt if so you will be is
big trouble.

After the worst has happened and ... 8-((( ... and
you are looking at a new door (or keep the old lock) then 18" Stillsons
applied to the brass euro cylinder might crack it in two (so the locksmiths say).
The brass is fairly brittle I beleive.

--
Ed Sirett - Property maintainer and registered gas fitter.
The FAQ for uk.diy is at www.diyfaq.org.uk
Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html
Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html