|
Double insulated wiring requirement
Hello,
I have a couple of X10 controlled appliance modules (see link below) which are essentially a remote controllable relay. I wish to use some of these to remotely switch floodlights on and off. However, they only have short lengths of single insulated wires coming from them. See he http://tinyurl.com/655v7 If I wire this into a junction box, this will leave exposed single insulated wiring. My understanding is that all accessable wiring should be double-insulated - is this correct? Do I need to mount these modules inside an enclosure to make them double-insulated?? (And "safe"?) Many thanks, Alan. |
On Mon, 29 Nov 2004 11:59:49 GMT, "Alan"
strung together this: If I wire this into a junction box, this will leave exposed single insulated wiring. My understanding is that all accessable wiring should be double-insulated - is this correct? Yes. Do I need to mount these modules inside an enclosure to make them double-insulated?? (And "safe"?) Yes. -- SJW A.C.S. Ltd Please reply to group or use 'usenet' in email subject |
In article ,
"Alan" writes: Hello, I have a couple of X10 controlled appliance modules (see link below) which are essentially a remote controllable relay. I wish to use some of these to remotely switch floodlights on and off. However, they only have short lengths of single insulated wires coming from them. See he http://tinyurl.com/655v7 Incidently, it's usually often to buy the plug-in appliance modules. If you disassemble them, you will find they consist of the part you bought, with the addition of a 13A plug/socket/fuse. ;-) If I wire this into a junction box, this will leave exposed single insulated wiring. My understanding is that all accessable wiring should be double-insulated - is this correct? Do I need to mount these modules inside an enclosure to make them double-insulated?? (And "safe"?) Yes as Lurch said. You could mount them in the top of a box with the upper part exposed for setting the housecode and unit numbers, but with the bottom opening and wires inside the box. That wouldn't be suitable for outdoor use though. You can also get DIN rail mounting ones which fit in a consumer unit. Actually, I bought an empty consumer unit just for mounting these. You could fit them in a waterproof CU or DIN rail box for outside use. The DIN rail ones are more expensive than the plug-in appliance modules though. The DIN rail lamp module is much better quality unit than it's plug-in equivalent though, always doing switch on/off through a smoothed dimming operation, and it includes a connection for operation via a momentary action switch if required, quite separately from X10 operation. (Also claims to support 'professional X10' whatever than is -- I think it might be scene settings, but I don't have anything which can talk 'professional X10' protocol to it.) -- Andrew Gabriel |
|
You can also get DIN rail mounting ones which fit in a consumer unit. Actually, I bought an empty consumer unit just for mounting these. You could fit them in a waterproof CU or DIN rail box for outside use. The DIN rail ones are more expensive than the plug-in appliance modules though. The DIN rail lamp module is much better quality unit than it's plug-in equivalent though, always doing switch on/off through a smoothed dimming operation, and it includes a connection for operation via a momentary action switch if required, quite separately from X10 operation. (Also claims to support 'professional X10' whatever than is -- I think it might be scene settings, but I don't have anything which can talk 'professional X10' protocol to it.) Andrew, I found some 'X10 professional' bits he http://www.homeautomation.eu.com/category/6 I like the look of the 4 channel dimming transmitter to fit inside existing light switches! I need to use the wired appliance modules to control some (fixed) floodlights, so plug-in modules won't help. I havn't used the DIN units yet, but may try them soon. However, looking at the one on the letsautomate website, if I fitted it into my existing CU it would't provide any current limiting breaker functionality like a MCB so would need fitting into it's own box downstram from the CU. They don't mention that on their website so I bet some people have them in CU's unprotected! Alan. |
On Mon, 29 Nov 2004 17:17:07 GMT, "Alan"
strung together this: I found some 'X10 professional' bits he http://www.homeautomation.eu.com/category/6 I like the look of the 4 channel dimming transmitter to fit inside existing light switches! Well whaddya know, I'm a pro and didn't know it! Didn't realise that's what it was. I've just been speccing some of that up for a job, thought it was just normal X10 stuff but a different make. -- SJW A.C.S. Ltd Please reply to group or use 'usenet' in email subject |
In article ,
"Alan" writes: You can also get DIN rail mounting ones which fit in a consumer unit. Actually, I bought an empty consumer unit just for mounting these. You could fit them in a waterproof CU or DIN rail box for outside use. The DIN rail ones are more expensive than the plug-in appliance modules though. The DIN rail lamp module is much better quality unit than it's plug-in equivalent though, always doing switch on/off through a smoothed dimming operation, and it includes a connection for operation via a momentary action switch if required, quite separately from X10 operation. (Also claims to support 'professional X10' whatever than is -- I think it might be scene settings, but I don't have anything which can talk 'professional X10' protocol to it.) Andrew, I found some 'X10 professional' bits he http://www.homeautomation.eu.com/category/6 That's who I bought most of my X10 bits from. They were the cheapest supplier I could find at the time, with a good range of items. I like the look of the 4 channel dimming transmitter to fit inside existing light switches! I need to use the wired appliance modules to control some (fixed) floodlights, so plug-in modules won't help. The point is, if you take a plug-in module apart, you end up with exactly the item in your photograph -- that's just the top half of the plug-in module. Plug-in modules are often cheaper (although not from that supplier). I havn't used the DIN units yet, but may try them soon. However, looking at the one on the letsautomate website, if I fitted it into my existing CU it would't provide any current limiting breaker functionality like a MCB so Correct. would need fitting into it's own box downstram from the CU. They don't or you cut the buzz bar short and just use the rest of the CU case for DIN rail mounted things. I used a separate CU case as a distribution/switching box for lighting. I also included a 3A Type B MCB to protect each DIN rail X10 dimmer, in the hope it might protect the triac if a failed lamp arcs across. They have a 20mm fuse on the front, but MCB's are probably faster operating and the dimmers are expensive enough that I would like to protect them best I can. mention that on their website so I bet some people have them in CU's unprotected! -- Andrew Gabriel |
The point is, if you take a plug-in module apart, you end up
with exactly the item in your photograph -- that's just the top half of the plug-in module. Plug-in modules are often cheaper (although not from that supplier). Pulled a plug-in module apart and confirmed this. "wired" version comes with a mounting bracket which could be useful though. They have a 20mm fuse on the front, but MCB's are probably Didn't know this - do now, thanks. Alan. |
| All times are GMT +1. The time now is 01:29 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter