UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
DavidD
 
Posts: n/a
Default replacing the glass in doors?

We have two back doors, both in different rooms, both with about 12 panes of
6x9 glass (or so) in them.

There is nothing wrong with the doors apart from they need a paint and some
of the glass is mismatched.
I thought I'd strip them both down, and replace the glass with new clear and
wondered if I should 'upgrade' the glass in an effort to make our house ever
so slightly warmer (I have an ongoing project to remove draughts etc).

Is it worthwhile? If so what sort of spec glass should I go for?

TIA

David


  #2   Report Post  
Bob Mannix
 
Posts: n/a
Default


"DavidD" wrote in message
. ..
We have two back doors, both in different rooms, both with about 12 panes

of
6x9 glass (or so) in them.

There is nothing wrong with the doors apart from they need a paint and

some
of the glass is mismatched.
I thought I'd strip them both down, and replace the glass with new clear

and
wondered if I should 'upgrade' the glass in an effort to make our house

ever
so slightly warmer (I have an ongoing project to remove draughts etc).

Is it worthwhile? If so what sort of spec glass should I go for?


You will be required to use 6mm glass (it probably is already unless it's
quite old). I presume you are thinking of K glass like the use in double
glazing. Not sure how available that is and whether it would make a
difference worth the price if not used as part of a double glazing set up. A
curtain across the door(s) would be cheaper and a lot more effective,
jeeping heat in and draughts out.


--
Bob Mannix
(anti-spam is as easy as 1-2-3 - not)


  #4   Report Post  
Dave Plowman (News)
 
Posts: n/a
Default

In article ,
DavidD wrote:
We have two back doors, both in different rooms, both with about 12
panes of 6x9 glass (or so) in them.


There is nothing wrong with the doors apart from they need a paint and
some of the glass is mismatched. I thought I'd strip them both down,
and replace the glass with new clear and wondered if I should 'upgrade'
the glass in an effort to make our house ever so slightly warmer (I
have an ongoing project to remove draughts etc).


Is it worthwhile? If so what sort of spec glass should I go for?


The only thing that will make a worthwhile difference is double glazed
panels. Solid glass - no matter how thick - will conduct the 'cold'.

--
*If your feet smell and your nose runs, you're built upside down.

Dave Plowman London SW
To e-mail, change noise into sound.
  #5   Report Post  
Mike
 
Posts: n/a
Default



Ziggur wrote:
Nope! The requirement is for "Safety Glass". Could be 4mm Toughened or
Laminated.


Go read the regs carefully.

6mm is suitable for panes of limited size.



  #6   Report Post  
Bob Mannix
 
Posts: n/a
Default


"Mike" wrote in message
. net...


Ziggur wrote:
Nope! The requirement is for "Safety Glass". Could be 4mm Toughened or
Laminated.


Go read the regs carefully.

6mm is suitable for panes of limited size.


In detail panes less than 250mm wide beween glazing beads (and with an area
not exceeding 0.5m^2 but you never usually reach that) can be of 6mm
annealed glass.

Above this size, safety glass is only required in windows where the glass is
below 800mm from the floor and, in doors, where it is below 1500mm from the
floor.

I believe "outbuildings" are not covered by these regulations - at least I
was able to buy a ~1m square sheet of 6mm for my old garage. I should say
this replaced a sheet of 3-4mm glass which my son had sent a football
through. I'm not a particularly nervous or sensationalist type when it
comes to safety but, had I been stood at my workbench at the time I would
have been hospitalized given the huge area of the garage that was filled
with medium size shards of razor sharp glass. The 6mm probably wouldn't have
broken anyway and the weight of the glass would have limited the danger
area - I feel a lot happier behind the 6mm!


--
Bob Mannix
(anti-spam is as easy as 1-2-3 - not)




Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
cutting glass tubing Ken Sterling Metalworking 33 June 27th 04 06:48 AM
New Front Door(s) Bruce Home Repair 4 December 10th 03 12:37 AM


All times are GMT +1. The time now is 05:27 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"