22mm to 15mm compression reducer
I'm installing an automatic air vent in the 22mm feed pipe to a shower pump.
The vent uses a 1/2" to 15mm connection. I was told the neatest way would be to use a 22-15mm reducer in the 22mm equal tee, off which is the vent. I've never used these before so some advise would be appreciated. I can see that it replaces the 22 mm olive, but I'm not sure which way up it should be. The obvious way has the reducer flush with the back edge of the 22mm nut when assembled, the other has it sticking proud about 5-8mm. My other question is how is the seal made with the 15mm pipe which inserts into the reducer. Does the reducer act as an olive and compress onto the pipe. This seems unlikely because it looks quite solid brass not capable of being crushed upto the 15mm pipe. thanks --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 26/02/2004 |
22mm to 15mm compression reducer
In an earlier contribution to this discussion,
Justin jsheldon@ remove me lineone.net wrote: I'm installing an automatic air vent in the 22mm feed pipe to a shower pump. The vent uses a 1/2" to 15mm connection. I was told the neatest way would be to use a 22-15mm reducer in the 22mm equal tee, off which is the vent. I've never used these before so some advise would be appreciated. I can see that it replaces the 22 mm olive, but I'm not sure which way up it should be. The obvious way has the reducer flush with the back edge of the 22mm nut when assembled, the other has it sticking proud about 5-8mm. My other question is how is the seal made with the 15mm pipe which inserts into the reducer. Does the reducer act as an olive and compress onto the pipe. This seems unlikely because it looks quite solid brass not capable of being crushed upto the 15mm pipe. thanks Don't really know - never used a reducer. What's wrong with a 22x22x15 tee? Much neater! -- Cheers, Set Square ______ Please reply to newsgroup. Reply address is Black Hole! |
22mm to 15mm compression reducer
On Sun, 07 Mar 2004 16:51:18 +0000, Justin wrote:
I'm installing an automatic air vent in the 22mm feed pipe to a shower pump. The vent uses a 1/2" to 15mm connection. I was told the neatest way would be to use a 22-15mm reducer in the 22mm equal tee, off which is the vent. I've never used these before so some advise would be appreciated. I can see that it replaces the 22 mm olive, but I'm not sure which way up it should be. The obvious way has the reducer flush with the back edge of the 22mm nut when assembled, the other has it sticking proud about 5-8mm. My other question is how is the seal made with the 15mm pipe which inserts into the reducer. Does the reducer act as an olive and compress onto the pipe. This seems unlikely because it looks quite solid brass not capable of being crushed upto the 15mm pipe. thanks There are two styles (at least) of reducer. One is in three parts with two brass parts which these can only be instered the right way, they clamp doen on a bog standard 15mm olive. The other is a single brass peice which again can only be fitted the right way and has a (very much) thinner section in the middle whcih nips the pipe and makes a seal. -- Ed Sirett - Property maintainer and registered gas fitter. The FAQ for uk.diy is at www.diyfaq.org.uk Gas fitting FAQ http://www.makewrite.demon.co.uk/GasFitting.html Sealed CH FAQ http://www.makewrite.demon.co.uk/SealedCH.html |
22mm to 15mm compression reducer
The other is a single brass peice which again can only be fitted the right
way and has a (very much) thinner section in the middle whcih nips the pipe and makes a seal. This is it. When its flush you cant see the reducer, it completely flush with the back of the nut, so it just as tidy as a 22x22x15 tee, plus I don't have to un-assemble the existing joint. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 26/02/2004 |
22mm to 15mm compression reducer
"Justin" jsheldon@ remove me lineone.net wrote in message ... I'm installing an automatic air vent in the 22mm feed pipe to a shower pump. The vent uses a 1/2" to 15mm connection. I was told the neatest way would be to use a 22-15mm reducer in the 22mm equal tee, off which is the vent. I've never used these before so some advise would be appreciated. I can see that it replaces the 22 mm olive, but I'm not sure which way up it should be. The obvious way has the reducer flush with the back edge of the 22mm nut when assembled, the other has it sticking proud about 5-8mm. My other question is how is the seal made with the 15mm pipe which inserts into the reducer. Does the reducer act as an olive and compress onto the pipe. This seems unlikely because it looks quite solid brass not capable of being crushed upto the 15mm pipe. thanks --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 26/02/2004 Hi Justin, Just curious here, why are you adding an AAV? Do the pump manufacturers require it? The only reason I ask is..... the feed to a pump will be under negative pressure when the pump is running, an AAV in the pump feed will let air into the system when the pump is running. BillP. |
22mm to 15mm compression reducer
Hi Justin,
Just curious here, why are you adding an AAV? Do the pump manufacturers require it? The only reason I ask is..... the feed to a pump will be under negative pressure when the pump is running, an AAV in the pump feed will let air into the system when the pump is running. BillP. You may have a point. I was copying the installation at my girlfriends, I best double check where the vents are on her pump. But wouldn't the head of water keep the feed under +ve pressure ? Both the cold and hot are 22mm pipe. The AAV will be on a 15mm stub out of the top of the Tee --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 26/02/2004 |
22mm to 15mm compression reducer
"Justin" jsheldon@ remove me lineone.net wrote in message ... ..But wouldn't the head of water keep the feed under +ve pressure ? Both the cold and hot are 22mm pipe. The AAV will be on a 15mm stub out of the top of the Tee Hi Justin, Maybe, not too sure what the dynamics of the system would be.I've just got a feeling that it would tend to draw air in. I've not yet seen a manufacturers installation guide requiring the addition of an AAV. Do you have the manufacturers instructions for the pump you are fitting, or are you following the other install as a guide. Providing the hot and cold feeds to the pump are made in such a way that air will not be drawn into the system and the pump is situated at low level, there shouldn't be a need for the AAV. Unless the manufacturer says different. |
22mm to 15mm compression reducer
"BillP" wrote in message ... "Justin" jsheldon@ remove me lineone.net wrote in message ... .But wouldn't the head of water keep the feed under +ve pressure ? Both the cold and hot are 22mm pipe. The AAV will be on a 15mm stub out of the top of the Tee Hi Justin, Maybe, not too sure what the dynamics of the system would be.I've just got a feeling that it would tend to draw air in. I've not yet seen a manufacturers installation guide requiring the addition of an AAV. Do you have the manufacturers instructions for the pump you are fitting, or are you following the other install as a guide. Providing the hot and cold feeds to the pump are made in such a way that air will not be drawn into the system and the pump is situated at low level, there shouldn't be a need for the AAV. Unless the manufacturer says different. I can't seem to find the instructions now, but I've been using the other install as a guide. I suppose when you first commision the system the vents help expel the air, but manual vents would do the same. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 27/02/2004 |
22mm to 15mm compression reducer
"Justin" jsheldon@ remove me lineone.net wrote in message ... I can't seem to find the instructions now, but I've been using the other install as a guide. I suppose when you first commision the system the vents help expel the air, but manual vents would do the same. Hi Justin, Yep, manual vents would be best, but even these should not be necessary. You would only need vents if you are fitting the pump at high level in the high point of an inverted U. This is usually a no no with most manufacturers (I believe there are special pumps made for this purpose but they're not the usual run of the mill).If you are fitting the pump at low level, bleeds should not be necessary. Of course, If you want to add manual vents to be sure, it can't do any harm. BillP |
22mm to 15mm compression reducer
Hi Justin,
Yep, manual vents would be best, but even these should not be necessary. You would only need vents if you are fitting the pump at high level in the high point of an inverted U. This is usually a no no with most manufacturers (I believe there are special pumps made for this purpose but they're not the usual run of the mill).If you are fitting the pump at low level, bleeds should not be necessary. Of course, If you want to add manual vents to be sure, it can't do any harm. BillP Decided to fit the vents but on a short stub above the pump on the pressure side of the pump. The pipe work here goes up from the pump, horizontal for a short while then down under the floor. The certainloy made filling and priming the pump a doddle, you could hear the air hissing out as the circuit filled. I then ran the shower with the power to the pump off to purge any remaining air. Supprising there was very little drop in flow or pressure than the previous gravity system. If I was to do this again I would perhaps save the money and use manual vents, although I do have peace of mind that any air will be automatically expelled. The shower is now a fantastic experience, I've used a 2.25 bar Salamander whole house pump which allows boosting of just one of the supplies. It boosts all the hot water downstairs (bathroom is downstairs) , since the new kitchen tap killed the hot water pressure. I felt like I'd been pressure washed this morning. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.596 / Virus Database: 379 - Release Date: 26/02/2004 |
All times are GMT +1. The time now is 03:17 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter