|
MIG welding with Nitrogen?
Gentlemen,
I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD |
MIG welding with Nitrogen?
On 04/09/2020 21:04, Cursitor Doom wrote:
Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ |
MIG welding with Nitrogen?
On 04/09/2020 22:15, Peter Hill wrote:
On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. |
MIG welding with Nitrogen?
On Sat, 5 Sep 2020 10:35:17 +0100, newshound
wrote: On 04/09/2020 22:15, Peter Hill wrote: On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. Problem is, the welds might *look* totally fine but be compromised strength-wise, as implied by the remarks on the site Peter pointed to. Since some of the stuff I'm doing is structural, I'm not convinced it's worth taking any chances with. Be interesting to experiment with, nevertheless. |
MIG welding with Nitrogen?
On 05/09/2020 14:34, Cursitor Doom wrote:
On Sat, 5 Sep 2020 10:35:17 +0100, newshound wrote: On 04/09/2020 22:15, Peter Hill wrote: On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. Problem is, the welds might *look* totally fine but be compromised strength-wise, as implied by the remarks on the site Peter pointed to. Since some of the stuff I'm doing is structural, I'm not convinced it's worth taking any chances with. Be interesting to experiment with, nevertheless. I was quite impressed by that site until I came to this: "Propylene isnt actually a pure gas, its a blend with Oxygen" Otherwise a fair point. But remember we usually assume that structures contain defects. So, where possible go for redundancy, or proof loading. But yes, it does very much depend on the application. My welding is such rubbish that I wouldn't do it on anything important. I still remember Florian Camathias killing himself because of a bad weld (although I thought it was reported as a braze). |
MIG welding with Nitrogen?
On 05/09/2020 21:45, newshound wrote:
On 05/09/2020 14:34, Cursitor Doom wrote: On Sat, 5 Sep 2020 10:35:17 +0100, newshound wrote: On 04/09/2020 22:15, Peter Hill wrote: On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. Problem is, the welds might *look* totally fine but be compromised strength-wise, as implied by the remarks on the site Peter pointed to. Since some of the stuff I'm doing is structural, I'm not convinced it's worth taking any chances with. Be interesting to experiment with, nevertheless. I was quite impressed by that site until I came to this: "Propylene isnt actually a pure gas, its a blend with Oxygen" Otherwise a fair point. But remember we usually assume that structures contain defects. So, where possible go for redundancy, or proof loading. But yes, it does very much depend on the application. My welding is such rubbish that I wouldn't do it on anything important. I still remember Florian Camathias killing himself because of a bad weld (although I thought it was reported as a braze). I suspect welding steel with N2 as the shield gas would be like an uncontrolled plasma nitriding process. The weld could very easily be more hard and brittle than desired. EN8 and some cast irons can be plasma nitrided and welding steel is basically a plasma process to deposit cast steel. https://www.wallworkht.co.uk/content/plasma_nitride/ |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 08:00:24 +0100, Peter Hill
wrote: On 05/09/2020 21:45, newshound wrote: On 05/09/2020 14:34, Cursitor Doom wrote: On Sat, 5 Sep 2020 10:35:17 +0100, newshound wrote: On 04/09/2020 22:15, Peter Hill wrote: On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. Problem is, the welds might *look* totally fine but be compromised strength-wise, as implied by the remarks on the site Peter pointed to. Since some of the stuff I'm doing is structural, I'm not convinced it's worth taking any chances with. Be interesting to experiment with, nevertheless. I was quite impressed by that site until I came to this: "Propylene isn’t actually a pure gas, it’s a blend with Oxygen" Otherwise a fair point. But remember we usually assume that structures contain defects. So, where possible go for redundancy, or proof loading. But yes, it does very much depend on the application. My welding is such rubbish that I wouldn't do it on anything important. I still remember Florian Camathias killing himself because of a bad weld (although I thought it was reported as a braze). I suspect welding steel with N2 as the shield gas would be like an uncontrolled plasma nitriding process. Sounds pretty cool! The weld could very easily be more hard and brittle than desired. That was my concern also. EN8 and some cast irons can be plasma nitrided and welding steel is basically a plasma process to deposit cast steel. https://www.wallworkht.co.uk/content/plasma_nitride/ Anyway, I suspect using N2 as a shield on structural areas of a vehicle could seriously come back and bite me on the arse, so I'll hang back until some more argon turns up. |
MIG welding with Nitrogen?
On 5/9/20 6:04 am, Cursitor Doom wrote:
Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Just use straight CO2 |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 19:50:03 +1000, F Murtz
wrote: On 5/9/20 6:04 am, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Just use straight CO2 Ain't got nun. All I have here currently is a full sized cylinder of UHP Hydrogen and a half-sized N2; both full. |
MIG welding with Nitrogen?
On 06/09/2020 08:00, Peter Hill wrote:
On 05/09/2020 21:45, newshound wrote: On 05/09/2020 14:34, Cursitor Doom wrote: On Sat, 5 Sep 2020 10:35:17 +0100, newshound wrote: On 04/09/2020 22:15, Peter Hill wrote: On 04/09/2020 21:04, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Nitrogen is used as a blanketing gas on back of stainless steel welds. This site says it won't work on mild steel. https://weldingpros.net/types-of-welding-gases/ As Brian implies, nitrides in steels change the mechanical properties. I'm not surprised that professionals don't recommend it on mild steel, but surely you have nothing to lose by doing some trials on dummy specimens. It all depends on how critical your welds are. Problem is, the welds might *look* totally fine but be compromised strength-wise, as implied by the remarks on the site Peter pointed to. Since some of the stuff I'm doing is structural, I'm not convinced it's worth taking any chances with. Be interesting to experiment with, nevertheless. I was quite impressed by that site until I came to this: "Propylene isnt actually a pure gas, its a blend with Oxygen" Otherwise a fair point. But remember we usually assume that structures contain defects. So, where possible go for redundancy, or proof loading. But yes, it does very much depend on the application. My welding is such rubbish that I wouldn't do it on anything important. I still remember Florian Camathias killing himself because of a bad weld (although I thought it was reported as a braze). I suspect welding steel with N2 as the shield gas would be like an uncontrolled plasma nitriding process. The weld could very easily be more hard and brittle than desired. EN8 and some cast irons can be plasma nitrided and welding steel is basically a plasma process to deposit cast steel. https://www.wallworkht.co.uk/content/plasma_nitride/ Yes, you would certainly get significant nitride formation. Some brittleness might be tolerable in a compression structure. But I still think it would be interesting to try on a test piece, followed by a standard extreme bend test. I'd have some confidence if it survived that. |
MIG welding with Nitrogen?
On 06/09/2020 11:50, Cursitor Doom wrote:
On Sun, 6 Sep 2020 19:50:03 +1000, F Murtz wrote: On 5/9/20 6:04 am, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Just use straight CO2 Ain't got nun. All I have here currently is a full sized cylinder of UHP Hydrogen and a half-sized N2; both full. Get a reel of cored wire? |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 12:30:50 +0100, newshound
wrote: Yes, you would certainly get significant nitride formation. Some brittleness might be tolerable in a compression structure. But I still think it would be interesting to try on a test piece, followed by a standard extreme bend test. I'd have some confidence if it survived that. Not me. What if the brittleness only develops over a period of weeks or months later? This would really need a long-term test under carefully controlled conditions before we could place any faith in its application in structural work. And I'm assuming that's already been done at some time and the results found wanting. |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 12:31:42 +0100, newshound
wrote: On 06/09/2020 11:50, Cursitor Doom wrote: On Sun, 6 Sep 2020 19:50:03 +1000, F Murtz wrote: On 5/9/20 6:04 am, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Just use straight CO2 Ain't got nun. All I have here currently is a full sized cylinder of UHP Hydrogen and a half-sized N2; both full. Get a reel of cored wire? Well I was wondering about that stuff, Newsy. I know it creates extra splatter compared to shielded, but that wouldn't matter in this case. But isn't it a bit too much like normal arc/stick welding? And if so, it's going to blow holes in the typically 0.7-0.8mm mild steel used for car sills and other structural areas like outriggers, surely? |
MIG welding with Nitrogen?
On 06/09/2020 12:40, Cursitor Doom wrote:
On Sun, 6 Sep 2020 12:30:50 +0100, newshound wrote: Yes, you would certainly get significant nitride formation. Some brittleness might be tolerable in a compression structure. But I still think it would be interesting to try on a test piece, followed by a standard extreme bend test. I'd have some confidence if it survived that. Not me. What if the brittleness only develops over a period of weeks or months later? This would really need a long-term test under carefully controlled conditions before we could place any faith in its application in structural work. And I'm assuming that's already been done at some time and the results found wanting. Maybe if you kept it at high temperatures, but that's just not the way nitrogen behaves in steel at ambient temperature. Case hardening and gas nitriding have been around for a long time. |
MIG welding with Nitrogen?
On 06/09/2020 12:44, Cursitor Doom wrote:
On Sun, 6 Sep 2020 12:31:42 +0100, newshound wrote: On 06/09/2020 11:50, Cursitor Doom wrote: On Sun, 6 Sep 2020 19:50:03 +1000, F Murtz wrote: On 5/9/20 6:04 am, Cursitor Doom wrote: Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD Just use straight CO2 Ain't got nun. All I have here currently is a full sized cylinder of UHP Hydrogen and a half-sized N2; both full. Get a reel of cored wire? Well I was wondering about that stuff, Newsy. I know it creates extra splatter compared to shielded, but that wouldn't matter in this case. But isn't it a bit too much like normal arc/stick welding? And if so, it's going to blow holes in the typically 0.7-0.8mm mild steel used for car sills and other structural areas like outriggers, surely? I gave away an inherited transformer stick welder before I bought the MIG, I couldn't do a thing with it which is doubtless down to my lack of technique. I did manage to fix a (non structural) hole in a Diahatsu panel once with gasless MIG. Not terribly neatly. I've done better on more favourable materials though. TBH I have not had the MIG out since I bought a little Lidl inverter welder for stick, I've been surprised how well I can re-fill the holes I sometimes make with it. As the You-tube videos for the generic ones confirm, the displayed amps are a bit optimistic but it's fine for one stick size down from the claimed maximum. Definitely a nice toy to have. But these days the cars go to a mate who owns a garage. |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 15:43:27 +0100, newshound
wrote: I gave away an inherited transformer stick welder before I bought the MIG, I couldn't do a thing with it which is doubtless down to my lack of technique. I did manage to fix a (non structural) hole in a Diahatsu panel once with gasless MIG. Not terribly neatly. I've done better on more favourable materials though. TBH I have not had the MIG out since I bought a little Lidl inverter welder for stick, I've been surprised how well I can re-fill the holes I sometimes make with it. As the You-tube videos for the generic ones confirm, the displayed amps are a bit optimistic but it's fine for one stick size down from the claimed maximum. Definitely a nice toy to have. But these days the cars go to a mate who owns a garage. It's still very handy to have a heafty arc welder, though. I keep a trolley-mounted 320 Amp Olympic oil cooled job made in England in 1973 (and still going strong) in the workshop for the big stuff. You can't beat it for heavy structural work like RSJs. I know you can do thick plate with MIG, but to match the penetrating power of a stick welder at that end of the scale you'd have to spend a small fortune on a MIG big enough to cut the mustard. |
MIG welding with Nitrogen?
Cursitor Doom Wrote in message:
On Sun, 6 Sep 2020 15:43:27 +0100, newshound wrote: I gave away an inherited transformer stick welder before I bought the MIG, I couldn't do a thing with it which is doubtless down to my lack of technique. I did manage to fix a (non structural) hole in a Diahatsu panel once with gasless MIG. Not terribly neatly. I've done better on more favourable materials though. TBH I have not had the MIG out since I bought a little Lidl inverter welder for stick, I've been surprised how well I can re-fill the holes I sometimes make with it. As the You-tube videos for the generic ones confirm, the displayed amps are a bit optimistic but it's fine for one stick size down from the claimed maximum. Definitely a nice toy to have. But these days the cars go to a mate who owns a garage. It's still very handy to have a heafty arc welder, though. I keep a trolley-mounted 320 Amp Olympic oil cooled job made in England in 1973 (and still going strong) in the workshop for the big stuff. You can't beat it for heavy structural work like RSJs. I know you can do thick plate with MIG, but to match the penetrating power of a stick welder at that end of the scale you'd have to spend a small fortune on a MIG big enough to cut the mustard. 240v where you are? -- Jimk ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
MIG welding with Nitrogen?
On Friday, September 4, 2020 at 9:04:44 PM UTC+1, Cursitor Doom wrote:
Gentlemen, I've run out of the ideal 90:10 mix of argon and CO2 for mild steel and was wondering if Nitrogen could be pressed into service as an expedient, given how long it takes for gas to be delivered currently. I have a nearly full half-size cylinder of pure nitrogen and it would be handy to say the least if it would make a workable substitute as an inert gas. Any thoughts? CD The use of nitrogen would produce various oxides of nitrogen, some of them deadly poisons. |
MIG welding with Nitrogen?
On Sun, 6 Sep 2020 18:35:52 +0100 (GMT+01:00), Jimk
wrote: Cursitor Doom Wrote in message: On Sun, 6 Sep 2020 15:43:27 +0100, newshound wrote: I gave away an inherited transformer stick welder before I bought the MIG, I couldn't do a thing with it which is doubtless down to my lack of technique. I did manage to fix a (non structural) hole in a Diahatsu panel once with gasless MIG. Not terribly neatly. I've done better on more favourable materials though. TBH I have not had the MIG out since I bought a little Lidl inverter welder for stick, I've been surprised how well I can re-fill the holes I sometimes make with it. As the You-tube videos for the generic ones confirm, the displayed amps are a bit optimistic but it's fine for one stick size down from the claimed maximum. Definitely a nice toy to have. But these days the cars go to a mate who owns a garage. It's still very handy to have a heafty arc welder, though. I keep a trolley-mounted 320 Amp Olympic oil cooled job made in England in 1973 (and still going strong) in the workshop for the big stuff. You can't beat it for heavy structural work like RSJs. I know you can do thick plate with MIG, but to match the penetrating power of a stick welder at that end of the scale you'd have to spend a small fortune on a MIG big enough to cut the mustard. 240v where you are? Yup, but it can be unreliable at times so I have a gennie which does single and 3 phase. |
| All times are GMT +1. The time now is 04:41 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter