Getting a part used stick out of a hot glue gun
 

Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

Cheers



Dave R



--
AMD FX-6300 in GA-990X-Gaming SLI-CF running Windows 7 Pro x64

--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

Getting a part used stick out of a hot glue gun
 

It is this a waste of thought and effort as the glue sticks are cheap

Richard

Getting a part used stick out of a hot glue gun
 

David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

I dont know if mine is a particularly poor design but it dribbles
incontinently most of the time. I would have thought that just leaving it
on for 30 minute say with the nozzle pointing downwards would result in the
glue just running out.

Tim

--
Please don't feed the trolls

Getting a part used stick out of a hot glue gun
 

Tim+ wrote:
David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

I dont know if mine is a particularly poor design but it dribbles
incontinently most of the time. I would have thought that just leaving it
on for 30 minute say with the nozzle pointing downwards would result in the
glue just running out.


Also, if the wood glue sticks are visually different then Im sure youll
spot when the new glue is coming through.

Tim

--
Please don't feed the trolls

Getting a part used stick out of a hot glue gun
 

On 30/04/2020 14:14, David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

Cheers



Dave R




I have that problem with changing colours of glue sticks. I create
hot-melt string, running out the whole of the remaining stick while
pushing in the new stick , with the gun held over a clean sheet of
metal, weaving back and forth, cold-shocks solid quickly into string,
holding farther off the sheet produces thinner string..
I use the string like using solder , wiith an old soldering iron , for
small gluing jobs. Mixing colours like paint on a pallette sometimes.
The alternative is to use 2 melt guns , one for each type of formulation.



--
Monthly public talks on science topics, Hampshire , England
http://diverse.4mg.com/scicaf.htm

Getting a part used stick out of a hot glue gun
 

On 30/04/2020 14:14, David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

Cheers



Dave R



Get it warm, when it is you should be able to pull the current stick out
of the back end. Fit new stick and pump through until you detect that
the material has changed.

Getting a part used stick out of a hot glue gun
 

On 30/04/2020 14:14, David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?


Allow the gun to heat, and then without any pressure on the trigger,
pull and twist the bit sticking out the back of the gun. It should come
out - although you will need to cut the blobby end of the retrieved
stick to get it back in the gun later.


--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

Getting a part used stick out of a hot glue gun
 

On 30/04/2020 15:11, Tim+ wrote:
David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

I dont know if mine is a particularly poor design but it dribbles
incontinently most of the time. I would have thought that just leaving it
on for 30 minute say with the nozzle pointing downwards would result in the
glue just running out.

The ones with a spring loaded ball valve in the outlet are better in
this respect - once the glue is no longer under pressure, the ball
should spring back and stop the escape (mostly!)


--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

Getting a part used stick out of a hot glue gun
 

N_Cook Wrote in message:
On 30/04/2020 14:14, David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

Cheers



Dave R




I have that problem with changing colours of glue sticks. I create
hot-melt string, running out the whole of the remaining stick while
pushing in the new stick , with the gun held over a clean sheet of
metal, weaving back and forth, cold-shocks solid quickly into string,
holding farther off the sheet produces thinner string..
I use the string like using solder , wiith an old soldering iron , for
small gluing jobs. Mixing colours like paint on a pallette sometimes.
The alternative is to use 2 melt guns , one for each type of formulation.

Steady! They're at least 7 quid each !!!!


--
Jimk


----Android NewsGroup Reader----
http://usenet.sinaapp.com/

Getting a part used stick out of a hot glue gun
 

"Tim+" wrote in message
...
David wrote:
Internet search is not my friend.

Standard procedure if you are using the same glue type is just to put a
new glue stick in and push the old one through as you use it up.

I need to change from wood glue to general purpose glue.

Is there a way to get the old stick out and preserve at least some of it
for future use?
Without buggering up the gun, of course.

Or is this a waste of thought and effort as the glue sticks are cheap?

I dont know if mine is a particularly poor design

Yes it is.

but it dribbles
incontinently most of the time.

None of mine have ever done that.

I would have thought that just leaving it
on for 30 minute say with the nozzle pointing downwards would result in
the
glue just running out.

Tim

--
Please don't feed the trolls

Getting a part used stick out of a hot glue gun
 

It can be done, but its rather difficult. I guess it depends how much of the
stick is, erm stuck!

Brian

--
----- --
This newsgroup posting comes to you directly from...
The Sofa of Brian Gaff...

Blind user, so no pictures please
Note this Signature is meaningless.!
"Tricky Dicky" wrote in message
...
It is this a waste of thought and effort as the glue sticks are cheap

Richard

More Heavy Trolling by Senile Nym-Shifting Rodent Speed!
 

On Fri, 1 May 2020 05:24:31 +1000, Joshua Snow, better known as cantankerous
trolling senile geezer Rodent Speed, wrote:

FLUSH the trolling senile asshole's latest troll**** unread

--
Richard about senile Rodent:
"Rod Speed, a bare faced pig and ignorant ****."
MID: