Joining guttering at 170 degrees
 

I have to end join two pieces of standard half round pvc guttering at 170
degrees (wall has a 10 degree kink due to property line)

Screwfix do an adjustable joiner but it only goes from 90 to 156 degreess -
does the panael have any suggestions - the gutters have to be at the same
height so I cannot drop from one into the other using a downpipe fitting.

Andrew Mawson

Joining guttering at 170 degrees
 

In article , Andrew Mawson
writes
I have to end join two pieces of standard half round pvc guttering at 170
degrees (wall has a 10 degree kink due to property line)

Screwfix do an adjustable joiner but it only goes from 90 to 156 degreess -
does the panael have any suggestions - the gutters have to be at the same
height so I cannot drop from one into the other using a downpipe fitting.

You could probably bend a straight length by 10 degrees if you heat the
middle up with a hot air gun. It works for cable trunking anyway which
is admittedly a bit smaller.
--
Tim Mitchell

Joining guttering at 170 degrees
 

On Wed, 25 Feb 2004 14:38:53 +0000 (UTC), "Andrew Mawson"
wrote:

I have to end join two pieces of standard half round pvc guttering at 170
degrees (wall has a 10 degree kink due to property line)

Screwfix do an adjustable joiner but it only goes from 90 to 156 degreess -
does the panael have any suggestions - the gutters have to be at the same
height so I cannot drop from one into the other using a downpipe fitting.

There is a little adjustment on a standard joint, you can get a
slightly out of square joint to seal quite satisfactorily. If it
doesn't, let silicone be your friend!
...

SJW
A.C.S. Ltd.

Joining guttering at 170 degrees
 

Andrew Mawson typed:

I have to end join two pieces of standard half round pvc guttering at
170 degrees (wall has a 10 degree kink due to property line)



I made my own faced with a similar situation.
Cut a _small_ section to required angle, stick ends together with plastic
weld and then a line of silicon over the top of the join.
Put a standard joiner each end. Its lasted 10 years so far.

--
Mark's Signature-Free Zone:

Joining guttering at 170 degrees
 

Andrew Mawson wrote:

I have to end join two pieces of standard half round pvc guttering at 170
degrees (wall has a 10 degree kink due to property line)

Screwfix do an adjustable joiner but it only goes from 90 to 156 degreess -
does the panael have any suggestions - the gutters have to be at the same
height so I cannot drop from one into the other using a downpipe fitting.

Andrew Mawson




For ##### sake.Just cut a v notch and use PVC weld to glue it back together.

Joining guttering at 170 degrees
 

"Mark" wrote in message


Andrew Mawson typed:

I have to end join two pieces of standard half round pvc guttering at
170 degrees (wall has a 10 degree kink due to property line)
I made my own faced with a similar situation.

Pausing to ponder, no doubt, on the benefit of not having an architect.


--
Posted via Mailgate.ORG Server - http://www.Mailgate.ORG

Joining guttering at 170 degrees
 

"Andrew Mawson" wrote in message ...
I have to end join two pieces of standard half round pvc guttering at 170
degrees (wall has a 10 degree kink due to property line)

Screwfix do an adjustable joiner but it only goes from 90 to 156 degreess -
does the panael have any suggestions - the gutters have to be at the same
height so I cannot drop from one into the other using a downpipe fitting.

Andrew Mawson

Worked with a plumber once. He used to cut two ends of the required
pipe/guttering/whatever to the angles he wanted, got himself a flat
hand shovel (shovel is better because you have something wooden to
hold on to), heated it up with his blow lamp (the flat metal bit that
is, not the handle) and then pushed the two pieces of plastic to be
joined into it - one either side - just hot enough to start to melt
the plastic. After he'd rapidly withdrawn the shovel he had two semi
moltend ends of pipe/guttering/whatever which he just shoved together
to form a perfect angle. Naturally he then held them steady to allow
the plastic to cool and form the joint.

If you fancy trying this method, cut two pieces of your guttering
about a foot long, make the angle and then joint up with connectors as
necessary...

HTH

Patrick

Joining guttering at 170 degrees
 

Michael McNeil typed:


Andrew Mawson typed:

I have to end join two pieces of standard half round pvc guttering
at 170 degrees (wall has a 10 degree kink due to property line)
I made my own faced with a similar situation.

Pausing to ponder, no doubt, on the benefit of not having an
architect.

Mine was an Edwardian Bay, the benefits of Architect's wisdom
doesn't seem to have improved over time. ;-(

Joining guttering at 170 degrees
 

"Mark" wrote in message
...
Michael McNeil typed:


Andrew Mawson typed:

I have to end join two pieces of standard half round pvc guttering
at 170 degrees (wall has a 10 degree kink due to property line)
I made my own faced with a similar situation.

Pausing to ponder, no doubt, on the benefit of not having an
architect.

Mine was an Edwardian Bay, the benefits of Architect's wisdom
doesn't seem to have improved over time. ;-(



Did an experimental join, cutting two short bit each 5 degrees on the skew,
and gluing them with normal solvent weld adhesive. So far so good but I'll
leave it for some days to harden before I trust it.

Thanks for the suggestions.

Andrew Mawson

Joining guttering at 170 degrees
 

Andrew Mawson wrote:

"Mark" wrote in message
...

Michael McNeil typed:


Andrew Mawson typed:


I have to end join two pieces of standard half round pvc guttering
at 170 degrees (wall has a 10 degree kink due to property line)

I made my own faced with a similar situation.

Pausing to ponder, no doubt, on the benefit of not having an
architect.

Mine was an Edwardian Bay, the benefits of Architect's wisdom
doesn't seem to have improved over time. ;-(




Did an experimental join, cutting two short bit each 5 degrees on the skew,
and gluing them with normal solvent weld adhesive. So far so good but I'll
leave it for some days to harden before I trust it.

Thanks for the suggestions.


Having trued to get solvent weld pipes apart, I'd say you are in for a
pleasant surprise.



Andrew Mawson

Joining guttering at 170 degrees
 

On Wed, 25 Feb 2004 23:47:16 -0000, "Mark" wrote:
Andrew Mawson typed:

I have to end join two pieces of standard half round pvc guttering at
170 degrees (wall has a 10 degree kink due to property line)



I made my own faced with a similar situation.
Cut a _small_ section to required angle, stick ends together with plastic
weld and then a line of silicon over the top of the join.
Put a standard joiner each end. Its lasted 10 years so far.

--
This would be my suggestion.

Rick