Temporarily turning off hot water in a combination boiler system?
 

I need to fix a hot tap in a sink in a relative's house (either clean
out & replace the washer, or perhaps replace the tap) --- that's
fine. But there's no service valve for this tap, and she has a
combination boiler.

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler, or do I
turn off the main stopcock coming in?

Thanks.

Temporarily turning off hot water in a combination boiler system?
 

Adam Funk wrote:

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler, or do I
turn off the main stopcock coming in?

There's no "correct" procedure. Just prevent the water flowing!

There's usually a valve on the cold water inlet of most combis.
Otherwise just turn off the cold on the stopcock.

No need to turn the heating off either.


--
Scott

Where are we going and why am I in this handbasket?

Temporarily turning off hot water in a combination boiler system?
 

On 25/11/16 18:20, Adam Funk wrote:
I need to fix a hot tap in a sink in a relative's house (either clean
out & replace the washer, or perhaps replace the tap) --- that's
fine. But there's no service valve for this tap, and she has a
combination boiler.

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler,

Unless there is a ballvalve isolator inline with the tap, there is no
standard valving - it's always house dependent.

or do I
turn off the main stopcock coming in?

Quite possibly.

Thanks.

Temporarily turning off hot water in a combination boiler system?
 

On 11/25/2016 6:32 PM, Tim Watts wrote:
On 25/11/16 18:20, Adam Funk wrote:
I need to fix a hot tap in a sink in a relative's house (either clean
out & replace the washer, or perhaps replace the tap) --- that's
fine. But there's no service valve for this tap, and she has a
combination boiler.

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler,

Unless there is a ballvalve isolator inline with the tap, there is no
standard valving - it's always house dependent.

or do I
turn off the main stopcock coming in?

Quite possibly.

Thanks.


Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned off.

Temporarily turning off hot water in a combination boiler system?
 

On 2016-11-26, newshound wrote:

On 11/25/2016 6:32 PM, Tim Watts wrote:
On 25/11/16 18:20, Adam Funk wrote:
I need to fix a hot tap in a sink in a relative's house (either clean
out & replace the washer, or perhaps replace the tap) --- that's
fine. But there's no service valve for this tap, and she has a
combination boiler.

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler,

Unless there is a ballvalve isolator inline with the tap, there is no
standard valving - it's always house dependent.

or do I
turn off the main stopcock coming in?

Quite possibly.

Thanks.


Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

Temporarily turning off hot water in a combination boiler system?
 

"Adam Funk" wrote in message
...
On 2016-11-26, newshound wrote:

On 11/25/2016 6:32 PM, Tim Watts wrote:
On 25/11/16 18:20, Adam Funk wrote:
I need to fix a hot tap in a sink in a relative's house (either clean
out & replace the washer, or perhaps replace the tap) --- that's
fine. But there's no service valve for this tap, and she has a
combination boiler.

What's the correct procedure for turning off the flow of hot water
from the boiler in order to cut the pipe and put a service valve in?
Should there be a valve somewhere downstream of the boiler,

Unless there is a ballvalve isolator inline with the tap, there is no
standard valving - it's always house dependent.

or do I
turn off the main stopcock coming in?

Quite possibly.

Thanks.


Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned
off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

Er, are you talking about turning off the heating aspect of the boiler or
turning off the water supply? I thought you were talking about replacing a
tap washer, which mean tuning off the water supply to that tap (either by
closing a stop vale of by turning off the rising main). Turning off the hot
water control at the boiler would simply ensure the water to the tap was
cold rather than hot - it wouldn't turn off the water flow itself. Maybe
I've misunderstood your phrase "her boiler has separate controls for turning
the CH & hot water on & off" - maybe you are referring to a tap rather than
a control switch. Or maybe your system has motorised stop valves, which
*would* mean that when HW is turned off at the boiler controller, water flow
was turned off.

Temporarily turning off hot water in a combination boiler system?
 

On 2016-11-29, NY wrote:

"Adam Funk" wrote in message
...
On 2016-11-26, newshound wrote:

Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned
off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

Er, are you talking about turning off the heating aspect of the boiler or
turning off the water supply? I thought you were talking about replacing a
tap washer, which mean tuning off the water supply to that tap (either by
closing a stop vale of by turning off the rising main). Turning off the hot
water control at the boiler would simply ensure the water to the tap was
cold rather than hot - it wouldn't turn off the water flow itself. Maybe
I've misunderstood your phrase "her boiler has separate controls for turning
the CH & hot water on & off" - maybe you are referring to a tap rather than
a control switch. Or maybe your system has motorised stop valves, which
*would* mean that when HW is turned off at the boiler controller, water flow
was turned off.

What I mean is this (just to clear):

1. turn the boiler control for hot water off;
2. turn off the main stopcock;
3. cut into the pipes and add service valves for the hot & cold taps
(might as well, in case the cold one goes next);
4. turn the main water back on & check that the service valves don't
leak;
5. turn the boiler control for hot water back on (so she can use hot
water at the other sinks);
6. fix the dodgy tap as necessary, reconnect, & turn the new service
valves on.

Temporarily turning off hot water in a combination boiler system?
 

Adam Funk wrote:

On 2016-11-29, NY wrote:

"Adam Funk" wrote in message
...
On 2016-11-26, newshound wrote:

Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned
off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

Er, are you talking about turning off the heating aspect of the boiler or
turning off the water supply? I thought you were talking about replacing a
tap washer, which mean tuning off the water supply to that tap (either by
closing a stop vale of by turning off the rising main). Turning off the hot
water control at the boiler would simply ensure the water to the tap was
cold rather than hot - it wouldn't turn off the water flow itself. Maybe
I've misunderstood your phrase "her boiler has separate controls for turning
the CH & hot water on & off" - maybe you are referring to a tap rather than
a control switch. Or maybe your system has motorised stop valves, which
*would* mean that when HW is turned off at the boiler controller, water flow
was turned off.

What I mean is this (just to clear):

1. turn the boiler control for hot water off;
2. turn off the main stopcock;
3. cut into the pipes and add service valves for the hot & cold taps
(might as well, in case the cold one goes next);
4. turn the main water back on & check that the service valves don't
leak;
5. turn the boiler control for hot water back on (so she can use hot
water at the other sinks);
6. fix the dodgy tap as necessary, reconnect, & turn the new service
valves on.

I assume the CH can't work with the hot water control turned off? This
seems to be true of all the combi boiler designs I've seen, though I am
happy to be proved ignorant.


--

Roger Hayter

Temporarily turning off hot water in a combination boiler system?
 

On 11/29/2016 8:56 PM, Roger Hayter wrote:
Adam Funk wrote:

On 2016-11-29, NY wrote:

"Adam Funk" wrote in message
...
On 2016-11-26, newshound wrote:

Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned
off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

Er, are you talking about turning off the heating aspect of the boiler or
turning off the water supply? I thought you were talking about replacing a
tap washer, which mean tuning off the water supply to that tap (either by
closing a stop vale of by turning off the rising main). Turning off the hot
water control at the boiler would simply ensure the water to the tap was
cold rather than hot - it wouldn't turn off the water flow itself. Maybe
I've misunderstood your phrase "her boiler has separate controls for turning
the CH & hot water on & off" - maybe you are referring to a tap rather than
a control switch. Or maybe your system has motorised stop valves, which
*would* mean that when HW is turned off at the boiler controller, water flow
was turned off.

What I mean is this (just to clear):

1. turn the boiler control for hot water off;
2. turn off the main stopcock;
3. cut into the pipes and add service valves for the hot & cold taps
(might as well, in case the cold one goes next);
4. turn the main water back on & check that the service valves don't
leak;
5. turn the boiler control for hot water back on (so she can use hot
water at the other sinks);
6. fix the dodgy tap as necessary, reconnect, & turn the new service
valves on.

I assume the CH can't work with the hot water control turned off? This
seems to be true of all the combi boiler designs I've seen, though I am
happy to be proved ignorant.


Certainly my experience. Forget items 1 and 5.

Temporarily turning off hot water in a combination boiler system?
 

On 2016-11-29, Roger Hayter wrote:

Adam Funk wrote:

On 2016-11-29, NY wrote:

"Adam Funk" wrote in message
...
On 2016-11-26, newshound wrote:

Don't Combis normally have a tap on the DHW outlet? That said, turning
off the main at the inlet (or the stop tap) is all that is needed. It's
perfectly safe to leave the CH running with the mains stop tap turned
off.

Thanks, everybody. I do remember that her boiler has separate
controls for turning the CH & hot water on & off.

I was wrong about that --- the HW control knob ranges from low to
high, not including off.

What I mean is this (just to clear):

1. turn the boiler control for hot water off;
2. turn off the main stopcock;
3. cut into the pipes and add service valves for the hot & cold taps
(might as well, in case the cold one goes next);
4. turn the main water back on & check that the service valves don't
leak;
5. turn the boiler control for hot water back on (so she can use hot
water at the other sinks);
6. fix the dodgy tap as necessary, reconnect, & turn the new service
valves on.

I assume the CH can't work with the hot water control turned off? This
seems to be true of all the combi boiler designs I've seen, though I am
happy to be proved ignorant.

AFAICT the CH did keep running with the water supply (main stopcock)
turned off; but I was wrong about being able to turn the HW function
off at the boiler (without turning the boiler completely off).