UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Richard Owen
 
Posts: n/a
Default Old plastering and fireplaces

Hi,

Just started to redo my living room – and have finished removing the
woodchip! The house is a 1860s Victorian mid-terrace and the walls are
currently plastered – the bottom layer having hair in it – so I guess
original. I have removed the skirts for replacement (along with big chunks
of plaster). I intend to have painted, plastered walls and ceiling, so a
good finish is essential. At some point UPVC double glazing front door and
windows were installed, but instead of being plastered right up to the
window, they put in fat white UPVC trim all around where the plaster
bead/corner should be and siliconed it all in (oh, and installed a thin
plastic windowsill for good measure!). I took this off, and the reason for
it (other than being cheap!) became obvious – it wasn’t rebeaded
underneath when the UPVC was installed. So…

- I want to remove the trim and plaster the corner/bead right up to the
window and door – will there be any problems with cracking due to shutting
and opening of the window/doors, i.e. do you seal the join with a flexible
material? What about draughts?
- Is there anything I need to be aware when plastering onto this old base
of hair-plaster. Some of it will have to be hacked off as its rattling,
but most is sound. Is there compatibility problems to be aware of?
- I have a few cracks in the lath and plaster ceiling – if they are taped
before plastering should this stop further cracking once skimmed over?
- I’m putting plastic channelling in for wires before plastering over them
– is it feasible to get wires into the channels after plastering – i.e. a
year later when I need to run another circuit for e.g.?
- Is plumbing hot water pipes into plaster acceptable?

I have a marble fireplace which I need installing at the same time. Would
you advise getting a specialist to do this first, or should any competent
plasterer be able to do this for me??

Any help, ideas or advice gratefully received.

Thanks,

Richard.


  #2   Report Post  
jerrybuilt
 
Posts: n/a
Default Old plastering and fireplaces

Richard Owen wrote:
Just started to redo my living room


"Living room" - better than "lounge", I suppose. Anyway:

– and have finished removing the woodchip! The house is a
1860s Victorian mid-terrace and the walls are currently
plastered – the bottom layer having hair in it – so I guess
original. I have removed the skirts for replacement (along
with big chunks of plaster). I intend to have painted, plastered
walls and ceiling, so a good finish is essential. At some point
UPVC double glazing front door and windows were installed,
but instead of being plastered right up to the window, they
put in fat white UPVC trim all around where the plaster
bead/corner should be and siliconed it all in (oh, and installed
a thin plastic windowsill for good measure!). I took this off,
and the reason for it (other than being cheap!) became
obvious – it wasn’t rebeaded underneath when the UPVC was
installed.


I would say that most PVC replacement windows are installed
to a standard that is not ideal. You should be able to improve
matters greatly. Check for draughts around badly-fitted
windows/cills.


So…

- I want to remove the trim and plaster the corner/bead
right up to the window and door – will there be any problems
with cracking due to shutting and opening of the window/doors,
i.e. do you seal the join with a flexible material?


Assuming the windows are fitted well, no. However... you may
need to affix a batten with screws and gripfill and render up
to it.

What about draughts?


Yes. Seal-o-foam may be useful.

- Is there anything I need to be aware when plastering onto
this old base of hair-plaster. Some of it will have to be hacked
off as its rattling, but most is sound. Is there compatibility
problems to be aware of?


Cut out loose areas. Apply dilute PVA to the brickwork and
plaster edges. PVA a good 6" onto the surface of the sound
plaster too, you will see why in a min. Patch holes with first
coat of 1:1:6 render, needn't be pretty, should be about 1/2
the thickness of your existing plaster (1/2"?). Drag a trowel
edgewise over the surface or score to key whilst still wet.
Leave it overnight at least to cure. Apply the top coat, 1:1:6
again. Use a straight edge to level. Allow to go off to a crumbly
consistency, and scrape the patch surface back a couple of mm
at least at the edges of the patch, preferably all over. You can
use a wallpaper stripper or similar or tack a bit of something
to your straight edge to make a scraper. The PVA that you
applied to the sound plaster around the hole to be patched
will have formed a scratch-resistant coat so you won't bugger
up the existing finish too much. You will end up with:

------------- ,,,,,-------
sound |...---''' new render scraped back at edge of patch
|
##################### existing brickwork

or:

------------
sound |-----------------------
| new render scraped back flat 2mm or so below sound

You might have to edit that to get it to show properly.

The purpose of scraping back at the patch edge (2-3" at least
if not scraping all over) is to allow for the skim coat. The skim
coat should be Thistle renovating finish or similar, multi-finish
is too hard. Make sure that there isn't a "step" at the edge of
the patch, or you'll have to mess with filler later to get anything
like a good finish.

- I have a few cracks in the lath and plaster ceiling – if they
are taped before plastering should this stop further cracking
once skimmed over?


Don't tape. I shouldn't skim, either, it's likely to be a waste of
time/money. DON'T rake out the cracks! Get a plastic squeezy
bottle and some 15mm foam pipe lagging. Tie 2" or so of lagging
onto the squeezy bottle (e.g. washing up bottle with nozzle
taken off). Make sure it is tied on well!! Wrap the lagging with
2" waterproof tape, and cut off at the top to form a flat surface.
Fill with dilute PVA, press the flat end of the lagging onto the
ceiling, squeeze bottle to force PVA into crack. This will glue
the crack together. You may need to wait overnight & re-do.
Use about 5:1, this will go into even hairline cracks. Wear a
bag over your hair! When all done, fill where needed with filler.
I would be VERY tempted to apply lining paper and paint that.


- I’m putting plastic channelling in for wires before plastering
over them
– is it feasible to get wires into the channels after plastering –
i.e. a year later when I need to run another circuit for e.g.?


Make sure your conduit is big enough, then OK. Why add wiring
later if you're p[lanning your lighting now? Can you explain a bit?


- Is plumbing hot water pipes into plaster acceptable?


I don't like this. Maybe OK if you wrapped them in foamed
poly sheet like very thin lagging first, but I wouldn't. A bit of
planning should allow you to box in in a corner or somewhere
else unobtrusive.


I have a marble fireplace which I need installing at the same
time. Would you advise getting a specialist to do this first, or
should any competent plasterer be able to do this for me??


If it's just the surround, anyone should be able to do it, but be
careful of getting muck on the marble,it stains. Solid fuel? Gas?
The "gubbins" may need special fitting.

be !
Shop all amazing products and get our special offers!
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT +1. The time now is 01:43 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"