Quantities for Shed Base
 

Afternoon,

I need to lay a concrete base for a shed. I recall needing a mixture of
ballast and cement, but need help in

a) what ratio to mix the cement to ballast
b) how much ballast and cement to order.

The shed size will be 10ft x 6ft.

I'm asuming the base will be around 6 inches deep (unless you guys advise
otherwise).

Thanks,
John

Quantities for Shed Base
 

John
wibbled on Sunday 04 April 2010 13:49

Afternoon,

I need to lay a concrete base for a shed.

If it's only a shed (rather than a heavy duty workshop) you could make life
easier and lay paving slabs on sand and optionally the sand on compacted
hardcore or Type 1 MOT (the latter would be better being whacked down with a
plate whacker, cheap to hire) Build a wooden frame around the perimeter to
set the levels, take off the loose soil and dig out if required to the right
depth, add hardcore (if using) and tamp/whack in. Add sand, tamp or whack
down and adjust finish level with a 7-8' tamping bar down to the level of
the wooden sidings.

Pave.

A long time ago, I did a shed on paving slabs on 2" sand with a little
cement added dry (about 1:10 - very weak) on soild with the top scraped off
mostly level. Left the wooden sides in, paved and watered in to start the
cement setting. Just enough cement to help stabilise the sand. Waited a week
then erected shed. It was happy for years so that's a measure of what you
*can* get away with. You just make some value judgements about the state of
the ground.

I recall needing a mixture of
ballast and cement, but need help in

a) what ratio to mix the cement to ballast
b) how much ballast and cement to order.

The shed size will be 10ft x 6ft.

I'm asuming the base will be around 6 inches deep (unless you guys advise
otherwise).

But if using actual concrete, then these may be of help:

http://www.pavingexpert.com/calcall.htm

For 6x10' at 4" thick, that would be 20 cu ft which is around 0.6m3 (do
check this again!)

If you're bothering to mix concrete, might as well go straight to a C20
which is a good strong general purpose mix ideal for slabs. The calculator
on that page says, rounded a bit

8 bags (25kg) cement
400kg sand
700kg gravel
180l of water.

400kg sand and 700kg gravel sounds a little more than a ton bag of ballast
(which can mean anything from 800kg to 1000kg), so that would be a
convenient measure, perhaps running the slab a little thinner and a bag less
of cement.

HTH

Tim

--
Tim Watts

Managers, politicians and environmentalists: Nature's carbon buffer.

Quantities for Shed Base
 

John wrote:

I need to lay a concrete base for a shed. I recall needing a mixture of
ballast and cement, but need help in

Why concrete?
A layer of slabs on a light mortar base would be far easier to lay, as
well as being very easy to take up if you ever want to move the shed.

The shed size will be 10ft x 6ft.
I'm asuming the base will be around 6 inches deep (unless you guys advise
otherwise).

6" deep?
How many tons are you expecting the shed to weigh?
I'd say a 3" layer of cement would be sufficient for any garden shed, if
the sub surface has been flattened/compacted.

Rough calcualtion - 10'x6' = 6 sq. M. , x 75mm depth = .45 cu M.
x 150depth = .9 sq. M.
A bulk bag of ballast will be roughly 850kgs (they are a nominal 1
tonne, but dont come very close IME.)
A bulk bag is roughly .75 Cu.M
A 10-1 mix would be fine for a shed I'd say, though for a harder surface
go to 6-1. So at 10-1, you need 85kg of cement, at 6-1, 140kg to mix
with 850kg of ballast.
850kg would give a depth of 4 to 5 inches.

Alan.
--
To reply by e-mail, change the ' + ' to 'plus'.

Quantities for Shed Base
 

replying to John, Darren wrote:
How much hardcore & sand do I need for 8/6 shed

--
for full context, visit https://www.homeownershub.com/uk-diy...se-624450-.htm

Quantities for Shed Base
 

I wish you folks would use the correct newsreaders instead of the mickey
mouse on at home owners club that messes up dates and leaves pictures
elsewhere.
Brian

--
----- --
This newsgroup posting comes to you directly from...
The Sofa of Brian Gaff...

Blind user, so no pictures please
Note this Signature is meaningless.!
"Darren" m wrote in
message oupdirect.com...
replying to John, Darren wrote:
How much hardcore & sand do I need for 8/6 shed

--
for full context, visit
https://www.homeownershub.com/uk-diy...se-624450-.htm

Quantities for Shed Base
 

On Thursday, 9 January 2020 17:14:05 UTC, Darren wrote:
replying to John, Darren wrote:
How much hardcore & sand do I need for 8/6 shed

What are you laying, a 4" base? Dried out masonry has a density of 2.2, and 3:1 should work good, so it can be calculated from there.

8'= 2.4m
6' = 1.8m
4" = 0.1m
2.4 x 1.6 x 0.1 = 0.384 cu m
x2.2 gets you 0.845 tonnes.


NT