Remove Silcone from Aluminium
 

Anyone know how to remove silicone sealant from aluminium ?

I need to remove all the old mouldy sealant from my shower surround
and have used Unibond silicone eater to clean off the shower tray and
tiles but it explicitly states not to use it on aluminium. (probably
because it contains Sulphuric acid) The shower surround has aluminium
supports and they to have a bead of sealant down the whole length
which I need to remove.

thanks in advance...
Andy

Remove Silcone from Aluminium
 

ac1951 wrote:

Anyone know how to remove silicone sealant from aluminium ?

I need to remove all the old mouldy sealant from my shower surround
and have used Unibond silicone eater to clean off the shower tray and
tiles but it explicitly states not to use it on aluminium. (probably
because it contains Sulphuric acid) The shower surround has aluminium
supports and they to have a bead of sealant down the whole length
which I need to remove.

Go and find your local steel stockist and ask if you can have some of
the steel banding that holds the steel together. It is about 25 to a
little more (less than 30) wide. Make sure that you can bend it to 90
degrees within a distance of 4 inches without it taking any shape.
If it takes on a bend, then you have the wrong steel. Go back and try again.

Take it home and with what ever you have, shorten it to about 6 -7
inches long.

Wrap lots of tough tape around the end that will become the handle and
make sure that your hand has no chance of contacting the metal; usually
by wrapping the tape overlapping the end and then folding it over and
then put another layer of tape over the whole lot.

Now take a file and make the cutting edge square.

Now file an edge on the top edge about the same angle as a chisel. I
tend to make the chisel edge (bevel) on the same side as the folded over
tape on the handle. This gives you the ability to pick up the tool and
know which way up it is.

After you have filed the cutting edge, comes the vital bit. If you are
right handed then you must put a very small radios on the left hand
corner, the same way and angle as you put on the cutting edge. And
preferably a much larger one on the other corner. (if you are left
handed, it should be transposed

Once this is done, if you feel the back of the cutting edge with your
fingernail, it will snag on the burr from the sharpening. It is
absolutely vital that you get rid of ALL this, as this will be the cause
of any scratches you leave on the ally.

To get rid
of this, rub the tool as flat as can be on either a file or a
sharpening stone, bevel side up.

Now you have the power to remove the silicon, keep the cutter very low,
about 5 degrees and when it starts to 'not' cut, it needs sharpening again.

Don't try to get all the silicon out of the corners unless you are sure
that they will get covered again

All this can be done with a chisel, but I didn't/could get my hands on
when I made one at work. Apart from which, it would have been too thick
for what I was using it for.

Dave

Remove Silcone from Aluminium
 

On Mar 7, 11:40*pm, Dave wrote:
ac1951 wrote:
Anyone know how to remove silicone sealant from aluminium ?

I need to remove all the old mouldy sealant from my shower surround
and have used Unibond silicone eater to clean off the shower tray and
tiles but it explicitly states not to use it on aluminium. (probably
because it contains Sulphuric acid) The shower surround has aluminium
supports and they to have a bead of sealant down the whole length
which I need to remove.

Go and find your local steel stockist and ask if you can have some of
the steel banding that holds the steel together. It is about 25 to a
little more (less than 30) wide. Make sure that you can bend it to 90
degrees within a distance of 4 inches without it taking any shape.
If it takes on a bend, then you have the wrong steel. Go back and try again.

Remove Silcone from Aluminium
 

ac1951 wrote:


many thanks for the comprehensive response ....
I have to admit that I was thinking you were going to end by saying
"tie the steel band around your wrist as a reminder never to try
removing silicone from aluminium" :)
thanks again

Just remember to keep the angle as low as possible and practice on
another piece of ally first. The angle should be as close to zero as is
possible. If the cutting edge is sharp, you should not have any problem.
Remember, if there is a burr under the cutting edge, it will cut into
the surface you are trying to clean up and make a scratch. I have done
this many times in the aerospace industry and never left a scratch when
I learned the way to do it. Practice first and then dive in. Try to hold
the blade in your hand, so that it is curved, so that the cutting edge
is horizontal, this will/should get you under the sealant.

I doubt that you will have to get right down to all the metal, as you
can normally use sealant over the top of traces of the last one.

Anyone care to comment?

Dave

Remove Silcone from Aluminium
 

On Mar 8, 11:30*pm, Dave wrote:
ac1951 wrote:
many thanks for the comprehensive response ....
I have to admit that I was thinking you were going to end by saying
"tie the steel band around your wrist as a reminder never to try
removing silicone from aluminium" *:)
thanks again

Just remember to keep the angle as low as possible and practice on
another piece of ally first. The angle should be as close to zero as is
possible. If the cutting edge is sharp, you should not have any problem.
Remember, if there is a burr under the cutting edge, it will cut into
the surface you are trying to clean up and make a scratch. I have done
this many times in the aerospace industry and never left a scratch when
I learned the way to do it. Practice first and then dive in. Try to hold
the blade in your hand, so that it is curved, so that the cutting edge
is horizontal, this will/should get you under the sealant.

I doubt that you will have to get right down to all the metal, as you
can normally use sealant over the top of traces of the last one.

Anyone care to comment?

Dave

OK job done,
I didn't use the metal band suggested by Dave but he set the idea. A
combination of using disposable safety razors and a kraft knife held
at a very shallow angle did the job...

thanks
Andy

Remove Silcone from Aluminium
 

ac1951 wrote:
On Mar 8, 11:30 pm, Dave wrote:

ac1951 wrote:

many thanks for the comprehensive response ....
I have to admit that I was thinking you were going to end by saying
"tie the steel band around your wrist as a reminder never to try
removing silicone from aluminium" :)
thanks again

Just remember to keep the angle as low as possible and practice on
another piece of ally first. The angle should be as close to zero as is
possible. If the cutting edge is sharp, you should not have any problem.
Remember, if there is a burr under the cutting edge, it will cut into
the surface you are trying to clean up and make a scratch. I have done
this many times in the aerospace industry and never left a scratch when
I learned the way to do it. Practice first and then dive in. Try to hold
the blade in your hand, so that it is curved, so that the cutting edge
is horizontal, this will/should get you under the sealant.

I doubt that you will have to get right down to all the metal, as you
can normally use sealant over the top of traces of the last one.

Anyone care to comment?

Dave


OK job done,
I didn't use the metal band suggested by Dave but he set the idea. A
combination of using disposable safety razors and a kraft knife held
at a very shallow angle did the job...

I am very glad to hear that :-)

Dave