Prepping walls after removing wall paper
 

Just moved into a house and started on the decorating. I've steamed
off two layers of painted wall paper in one room, under which is
painted plaster. In some areas I've taken the base paint off as well
as the paper so just plaster showing, in others the paint is left
there.

Don't think I need to go to the trouble of sanding off all of the
paint? But concerned the slight 'edge' between the patches where these
is no paint will show through?

There are a couple of scraper 'scars' which I intended to fill with
traditional filler.

What prep do I need to do now - will a good base layer suffice, prior
to putting on my chosen colour? Or do I need to use the skim finish
filler products to smooth it over


Any tips and suggestions please.

Many thanks

Prepping walls after removing wall paper
 

southview3 wrote:
Just moved into a house and started on the decorating. I've steamed
off two layers of painted wall paper in one room, under which is
painted plaster. In some areas I've taken the base paint off as well
as the paper so just plaster showing, in others the paint is left
there.

Don't think I need to go to the trouble of sanding off all of the
paint? But concerned the slight 'edge' between the patches where these
is no paint will show through?

There are a couple of scraper 'scars' which I intended to fill with
traditional filler.

What prep do I need to do now - will a good base layer suffice, prior
to putting on my chosen colour? Or do I need to use the skim finish
filler products to smooth it over


Any tips and suggestions please.

Many thanks


Best to skim it with something fine. Filler is good for small areas but
you may find you're doing the whole wall, which can get a bit pricey.
Wickes ready mixed skim coat is a good compromise if you can't be
bothered mixing

Prepping walls after removing wall paper
 

southview3 wrote:
Just moved into a house and started on the decorating. I've steamed
off two layers of painted wall paper in one room, under which is
painted plaster. In some areas I've taken the base paint off as well
as the paper so just plaster showing, in others the paint is left
there.

Don't think I need to go to the trouble of sanding off all of the
paint? But concerned the slight 'edge' between the patches where these
is no paint will show through?

I'm assuming you want to paint the wall now, not wallpaper?

If so, I think you'll need to do something about the surface blemishes
or they will show through.... though this does depend on the thickness
of the original paint layer (and therefore of the 'edges' of the
blemishes) and of the new paint. Possible solutions:

Sanding just the aforementioned 'edges' to minimise the visible ridge;

Sand the whole wall with an orbital sanding machine or similar;

Cover over all the bad bits using filler, or skim the whole wall;

Repaper using a thick grade lining paper, then paint that.

If you're going for options 1-3 it might be worth trying it out a couple
of test areas and then painting those with your chosen paint, to see if
it's acceptable.

David






Why not just try a test area if you're worried?

Prepping walls after removing wall paper
 

On Jun 29, 7:41 am, Lobster wrote:
southview3 wrote:
Just moved into a house and started on the decorating. I've steamed
off two layers of painted wall paper in one room, under which is
painted plaster. In some areas I've taken the base paint off as well
as the paper so just plaster showing, in others the paint is left
there.

Don't think I need to go to the trouble of sanding off all of the
paint? But concerned the slight 'edge' between the patches where these
is no paint will show through?

I'm assuming you want to paint the wall now, not wallpaper?

If so, I think you'll need to do something about the surface blemishes
or they will show through.... though this does depend on the thickness
of the original paint layer (and therefore of the 'edges' of the
blemishes) and of the new paint. Possible solutions:

Sanding just the aforementioned 'edges' to minimise the visible ridge;

Sand the whole wall with an orbital sanding machine or similar;

Cover over all the bad bits using filler, or skim the whole wall;

Repaper using a thick grade lining paper, then paint that.

If you're going for options 1-3 it might be worth trying it out a couple
of test areas and then painting those with your chosen paint, to see if
it's acceptable.

David

Why not just try a test area if you're worried?

Many thanks - yes test and revise will be the way forward I think.
Justdon't want to have to go back over too many steps. Thanks for your
suggestions.