Replacement Briggs and Stratton engine
 

I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

Thanks

Rob

Replacement Briggs and Stratton engine
 

robgraham wrote:
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

Thanks

Rob

Generally its the valves needing regrinding.

IIRC new pistons and liners can also be obtained.

A whole new engine is usually when you have bent the crank and split the
crankase.

Any B & S stockist can get you parts,or a new engine.

Replacement Briggs and Stratton engine
 

"robgraham" wrote in message
ps.com...
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

Thanks

Rob

Ebay

Replacement Briggs and Stratton engine
 

robgraham wrote in message
ps.com...
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?


As NP said its normally only the valves that need attention
New engines, but ridiculously expensive
http://www.briggsbits.co.uk/acatalog...hortblocks_.ht
ml
best place is your local tip, as most cylinder mowers usually end up there
with a working engine.



-

Replacement Briggs and Stratton engine
 

robgraham wrote:
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

I have one on a good mower whose plastic body is broken beyond repair.
Where are you? email me for more info if you are anywhere near Cambridge.
Douglas de Lacey

Replacement Briggs and Stratton engine
 

On 1 Aug 2006 14:04:27 -0700, robgraham wrote:

I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

Probably cheaper to go to one of the sheds and buy a whole new mower than
getting a new engine from your local B&S dealer. If you existing body etc
is good buy a really cheapy mower just for the engine and dump all the
new body bits. Though if your careful with choice many parts could be
used as spares...

--
Cheers
Dave. pam is missing e-mail

Replacement Briggs and Stratton engine
 

Dave Liquorice wrote:
On 1 Aug 2006 14:04:27 -0700, robgraham wrote:

I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

Probably cheaper to go to one of the sheds and buy a whole new mower than
getting a new engine from your local B&S dealer. If you existing body etc
is good buy a really cheapy mower just for the engine and dump all the
new body bits. Though if your careful with choice many parts could be
used as spares...

--
Cheers
Dave. pam is missing e-mail

Thanks for all your replies and the ideas, guys; can't be sure but sure
but someone somewhere talked about some sort of dump near him where old
mowers etc ended up and I wondered what sort of dump - no doubt if I
did find such a place locally I wouldn't be allowed to do the logical
thing of recycling, but it's probably worth some beer tokens to get the
guy to switch his eyes somewhere else for 5 minutes.

I'll try searching the archives of the NG's I use.

Cheers

Rob

Replacement Briggs and Stratton engine
 

In article om,
robgraham wrote:
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

It's fairly easy to find out why the compression is low especially if
you've already had a look and found nothing obviously wrong like a hole in
the piston. ;-)

Add a couple of teaspoons of engine oil via the sparkplug hole. If the
compression returns, it's likely ring wear or even broken ones. If no
difference, likely the valves. With the head removed, fill the ports with
paraffin. A faulty valve will allow this to run past it. Most likely valve
to fail is the exhaust one. Remove them both and examine valves and seats.
No obvious damage means they can be lapped in by hand. If the seat is
damaged a decent car etc engineering workshop will re-cut it for you. The
valve may also be refaced or simply replaced if damaged.

--
*Oh, what a tangled website we weave when first we practice *

Dave Plowman London SW
To e-mail, change noise into sound.

Replacement Briggs and Stratton engine
 

On 3 Aug 2006 01:06:53 -0700, robgraham wrote:

some sort of dump near him where old mowers etc ended up and I wondered
what sort of dump

The local council dump, I think they call them "household waste amenity
centres" or something with recycling in the name these days.

--
Cheers
Dave. pam is missing e-mail

Replacement Briggs and Stratton engine
 

"Dave Plowman (News)" wrote in message
...
In article om,
robgraham wrote:
I saw a comment I think in this NG about finding replacement B & S
engines - the one on my cylinder lawn mower has lost compression and I
can't find why despite stripping most of it down and the solution seems
to be to find a replacement. The question is where to go to ?

It's fairly easy to find out why the compression is low especially if
you've already had a look and found nothing obviously wrong like a hole in
the piston. ;-)

Add a couple of teaspoons of engine oil via the sparkplug hole. If the
compression returns, it's likely ring wear or even broken ones. If no
difference, likely the valves. With the head removed, fill the ports with
paraffin. A faulty valve will allow this to run past it. Most likely valve
to fail is the exhaust one. Remove them both and examine valves and seats.
No obvious damage means they can be lapped in by hand. If the seat is
damaged a decent car etc engineering workshop will re-cut it for you. The
valve may also be refaced or simply replaced if damaged.

Are these engines air cooled, side valve ones? What kind of cylinder head
gasket (if any) do they have?

Sylvain.

--
*Oh, what a tangled website we weave when first we practice *

Dave Plowman London SW
To e-mail, change noise into sound.

Replacement Briggs and Stratton engine
 

Sylvain VAN DER WALDE wrote in message
...

"Dave Plowman (News)"
.. With the head removed, fill the ports with
paraffin. A faulty valve will allow this to run past it. .

Are these engines air cooled, side valve ones? What kind of cylinder head
gasket (if any) do they have?



Quite probably, if the OP has the model number a Manual/Illustrated Parts
list in PDF is available from
http://shop.briggsandstratton.com/BS...MECID=100&CATA
LOGID=56B2B9AF-283C-11D4-8886-00B0D0203414&lrid=&page=7&SessionID=6526B2D8-0
6D4-4F91-ACA8-7A14EC45832E

http://tinyurl.com/o2tas


-