Lath & Plaster Ceiling
Hi,
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Any ideas ? S |
Séan Connolly wrote:
Hi, Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Any ideas ? S There is no easy way except with an hammer. Why worry about the lath, screw the plaster board to the joist. |
Take the lath off too - most of it will break anyway, and it won't be
level enough to plasterboard over. Use a claw hammer & wrecking bar. Prepare to be amazed at how much volume of crap you pull down! |
Séan Connolly wrote:
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. ??? Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. You remove the lath + plaster. You can either kick it down from above, or if there's a floor above you pull it down from below with a crowbar. -- Grunff |
Grunff wrote: S=E9an Connolly wrote: Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact,= how to remove the plaster as I want to keep the lath to put the plasterboar= d on. ??? Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it a= ll down. You remove the lath + plaster. You can either kick it down from above, or if there's a floor above you pull it down from below with a crowbar. -- Grunff The edges of the lathes overlap so if you don't take the lathes down the plasteboard wont be flat.I pulled it down with a claw hammer or crow bar then meticulously pulled the hundreds of nails out rather than knocking the in. Kevin |
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact,
how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Chears, lath + plaster down it is :) |
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact,
how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? |
"Séan Connolly" mrcATseanDASHconnollyDOTcoDOTuk wrote in message ... Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? Don't undersetimate the amount of dirt and dust involved. Open the windows, seal the door and wear a good respirator. No matter how much dirt and dust you expect, there will be more. Its one of the filthiest jobs there is. |
Séan Connolly wrote:
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Chears, lath + plaster down it is :) I know if I was going to do this I would solidly secure a dust sheet to the ceilng in a four corner arrangement and knock the corners into the dust sheet via the loft if permitting, this would then lessen the clearing up process and dust and make it more easy. :-) |
Don't undersetimate the amount of dirt and dust involved. Open the
windows, seal the door and wear a good respirator. No matter how much dirt and dust you expect, there will be more. Its one of the filthiest jobs there is. Yeah the guy who is doing all the plastering mentioned this ! The original idea was for him to do the whole lot, but in an atempt to keep costs down I'm doing the unskilled & dirty stuff :( Could I not cut though the wall with an angle grinder and take the thing down in one piece ? Actually come to think of it that will probably set fire to the wall, so not a good idea! |
I know if I was going to do this I would solidly secure a dust sheet to
the ceilng in a four corner arrangement and knock the corners into the dust sheet via the loft if permitting, this would then lessen the clearing up process and dust and make it more easy. :-) I was thinking along these lines, but having the sheet on the floor. I presume you basically go in the loft, roll back the insulation and kick the ceiling out, having previously figured out where it actually is from above! |
On Thu, 8 Sep 2005 08:43:46 +0100, "Séan Connolly"
mrcATseanDASHconnollyDOTcoDOTuk wrote: Whats the easist way ro remove a Lath & Plaster ceiling ? There isn't one - which is why plasterboard is often fitted on it rather than removing it all. To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. The plaster curls back over the laths, you cannot really remove the plaster without bringing down the laths. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Not only does it take time it generates a huge amount of mess as years of dust and debris come down with it. -- Peter Parry. http://www.wpp.ltd.uk/ |
Séan Connolly wrote:
Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Can you get above it? If so, just tread it down, or use a baulk of timber (watch for blisters!). If you can't get above it, use a pick-axe and pull it down from below. When it's down, pull out any nails which held the lath using a claw hammer. Rake out the top of the wall plaster to receive and support the edges of your plasterboard. When you put new plasterboard up, use 2" ELH clouts every 6" minimum, or 30mm drywall screws, taking great care not to screw through the paper face of the PB. Dust is a big issue - tape up the door(s) when taking down and clearing up, use breathing protection - I greatly favour an air helmet (run off a vacuum cleaner outside). |
Séan Connolly wrote:
Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? If it's that bad, remove the P&L, fix up any cabling you need to do, ensuring that it can be pulled through to replace in future if need be, and replace the P&L with two layers of 1/2" PB. |
in 445430 20050908 121205 Chris Bacon wrote:
Séan Connolly wrote: Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? If it's that bad, remove the P&L, fix up any cabling you need to do, ensuring that it can be pulled through to replace in future if need be, and replace the P&L with two layers of 1/2" PB. Where do you get 1/2 inch plasterboard? B&Q and Wickes only seem to stock 9.5mm pb |
Séan Connolly wrote:
Could I not cut though the wall with an angle grinder and take the thing And you think pulling down L&P makes dust wait until you get an angle grinder into the equation! down in one piece ? Actually come to think of it that will probably set fire to the wall, so not a good idea! If you need to cut it a bit more neatly then you can knock a hole through it and then use a reciprocating saw. -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
Bob Martin wrote:
Chris Bacon wrote: two layers of 1/2" PB. Where do you get 1/2 inch plasterboard? B&Q and Wickes only seem to stock 9.5mm pb I've seen 1/2" (12.5mm) in B&Q, but can't see *any* PB on their useless website. It's commonly available, I'm surprised that these DIY places don't have it - all BMs do. |
"Séan Connolly" mrcATseanDASHconnollyDOTcoDOTuk wrote in message ... .... Could I not cut though the wall with an angle grinder and take the thing down in one piece ? ... If it needs replacing, it won't come down in one piece, whatever you do. Colin Bignell |
Bob Martin wrote:
in 445430 20050908 121205 Chris Bacon wrote: Séan Connolly wrote: Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? If it's that bad, remove the P&L, fix up any cabling you need to do, ensuring that it can be pulled through to replace in future if need be, and replace the P&L with two layers of 1/2" PB. Where do you get 1/2 inch plasterboard? B&Q and Wickes only seem to stock 9.5mm pb Silly question this but...have you tried a DIY/local builders yard? |
In article , "S=E9an=
=20 Connolly" mrcATseanDASHconnollyDOTcoDOTuk says... I know if I was going to do this I would solidly secure a dust sheet to= =20 the ceilng in a four corner arrangement and knock the corners into the dust sheet via the loft if permitting, this would then lessen the clearing u= p process and dust and make it more easy. :-) =20 =20 I was thinking along these lines, but having the sheet on the floor. I= =20 presume you basically go in the loft, roll back the insulation and kick t= he=20 ceiling out, having previously figured out where it actually is from abov= e!=20 =20 By far the best way - otherwise you're standing under it as you pull it=20 down. You'll still have to remove some bits of lath and nails from=20 below, but most of the plaster will be gone by then. Most of the nails=20 will probably come out with a hammer and bolster rather than using=20 pincers or a claw hammer on each one, and any broken ones can just be=20 hammered flat. You will probably be surprised at how much rubble you=20 have created. |
In article , "S=E9an=
=20 Connolly" mrcATseanDASHconnollyDOTcoDOTuk says... Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact,= =20 how to remove the plaster as I want to keep the lath to put the=20 plasterboard on. Allthough its cracked and water damaged it still seems pretty robust in= =20 places and attacking it with a hammer is going to take ages to get it a= ll=20 down. =20 =20 Actually I have one wall that is lath and plaster as well (basically a=20 partition wall), on which the plaster is pretty shagged. Would the same= =20 apply, just remove the whole lot and put up a new partition wall ?=20 =20 There's no point replacing the framing if that's still sound - strip the=20 plaster and lath, then see what it's like underneath. |
"Chris Bacon" wrote in message ... Séan Connolly wrote: Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Can you get above it? If so, just tread it down, or use a baulk of timber (watch for blisters!). snip ================== I used a garden spade (from above) - no blisters and much less danger of falling through the joists! It chopped off the laths easily leaving just the nails to remove once the dust had settled. Cic. |
"ben" wrote in message .uk... Bob Martin wrote: in 445430 20050908 121205 Chris Bacon wrote: Séan Connolly wrote: Actually I have one wall that is lath and plaster as well (basically a partition wall), on which the plaster is pretty shagged. Would the same apply, just remove the whole lot and put up a new partition wall ? If it's that bad, remove the P&L, fix up any cabling you need to do, ensuring that it can be pulled through to replace in future if need be, and replace the P&L with two layers of 1/2" PB. Where do you get 1/2 inch plasterboard? B&Q and Wickes only seem to stock 9.5mm pb Silly question this but...have you tried a DIY/local builders yard? Cheapest place I know of is magnet (yep the kitchen place). |
In article ,
Bob Martin writes: Where do you get 1/2 inch plasterboard? B&Q and Wickes only seem to stock 9.5mm pb My local Wickes stocks it. Wheeled 3 large sheets of it home on one of their trollies. -- Andrew Gabriel |
Andrew Gabriel wrote:
Where do you get 1/2 inch plasterboard? My local Wickes stocks it. Wheeled 3 large sheets of it home on one of their trollies. What's a "large sheet"? 12.5/15/19mm thick by 2700/3000x1200? OK, I'm not serious here. 8x4x1/2" |
S=E9an Connolly wrote:
Hi, Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, h= ow to remove the plaster as I want to keep the lath to put the plasterboard = on. Allthough its cracked and water damaged it still seems pretty robust in places and attacking it with a hammer is going to take ages to get it all down. Any ideas ? S Everyone so far has recommenedd breaking it down, but this is not a good idea imho. Since IIRC your ceiling is not at risk of falling down, the logical thing is to PB over it. Advantages: 1=2E avoids the mess from hell that pulling down L&P creates. Everyone seems to think they can use dust sheets and avoid the worst of it, but the reality is everything in the room will be trashed. I know cos I've done it. 2=2E PBing over it thus avoids having to empty the room. 3=2E You then put up 1 layer PB onto a fairly flt surface, rather than 2 layer onto joists with 1000 nails poking out. 4=2E You end up with much better sound insulation if you keep the L&P there. And a better rated firebreak as well. Unless the L&P is dangerous there is really no good reason to pull it down. Those ceilings have often lasted a century and are happy to continue for decades ahead. The other option is to skim the L&P, with no PB. PS always use proper PB screws on PB, forget trying to nail it. NT |
Séan Connolly wrote:
Hi, Whats the easist way ro remove a Lath & Plaster ceiling ? To be exact, how to remove the plaster as I want to keep the lath to put the plasterboard on. Any ideas ? quickest and by far the cleanest is to overboard the whole lot with long screws then skim over. We had this done with several large(ish) ceilings in the flat above our shop about 6 years ago and there's been no problem with any cracking or movement or anything. the added layer will prolly help with sound reduction and heat loss to a degree. -- http://gymratz.co.uk - Best Gym Equipment & Bodybuilding Supplements UK. http://trade-price-supplements.co.uk - TRADE PRICED SUPPLEMENTS for ALL! http://fitness-equipment-uk.com - UK's No.1 Fitness Equipment Suppliers. http://gymratz.co.uk/hot-seat.htm - Live web-cam! (sometimes) |
Chris Bacon wrote:
Can you get above it? If so, just tread it down I did this accidentally while a few boards were up. Needless to say, a foot & leg through a plaster lath ceiling is very difficult to escape from and fairly painful. you need to hang on to stop going through further but need to let go to try and snap off the individual laths to allow removal of ones appendage. -- http://gymratz.co.uk - Best Gym Equipment & Bodybuilding Supplements UK. http://trade-price-supplements.co.uk - TRADE PRICED SUPPLEMENTS for ALL! http://fitness-equipment-uk.com - UK's No.1 Fitness Equipment Suppliers. http://gymratz.co.uk/hot-seat.htm - Live web-cam! (sometimes) |
|
Unless the L&P is dangerous there is really no good reason to pull it
down. Those ceilings have often lasted a century and are happy to continue for decades ahead. Its pretty badly bowed which seems to sugest that the l&p has come away from the joists (in fact it looks like the celing rose is holding it up!) |
Séan Connolly wrote:
Unless the L&P is dangerous there is really no good reason to pull it down. Those ceilings have often lasted a century and are happy to continue for decades ahead. Its pretty badly bowed which seems to sugest that the l&p has come away from the joists (in fact it looks like the celing rose is holding it up!) That'll strain your plasterboard fixings... |
Chris Bacon wrote:
Its pretty badly bowed which seems to sugest that the l&p has come away from the joists (in fact it looks like the celing rose is holding it up!) That'll strain your plasterboard fixings... You could counter batten it first, and fix those with more serious screws to pull the L&P back into line. The fix the PB to the counter battens. -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
Owain wrote:
Battening might strain the plaster to cracking. Perhaps loosly fitting It might, but would you care if you are going to PB over it anyway? plywood under the ceiling, then acropropping it up to push the laths This technique can work for reparing a L&P ceiling - push it back temporarily and then pour extra bonding plaster on top to stabilise it... -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
Owain wrote:
Battening might strain the plaster to cracking. Perhaps loosly fitting It might, but would you care if you are going to PB over it anyway? I was thinking the PB might not have sufficient pull-through strenth on its fixings to support the weight of L&P if the L&P was sagging? Yup, see what you are getting at. I think we are taking at cross purposes. I was suggesting that cross battens at 400mm c/c be screwed through the L&P into the joists with decent screws. The cross battens alone will then fix the L&P very firmly in place and eliminate any sag. The PB would then be screwed to the battens (rather than the joists or L&P), using drywall screws in the normal way. -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
John Rumm wrote:
Owain wrote: Battening might strain the plaster to cracking. Perhaps loosly fitting It might, but would you care if you are going to PB over it anyway? plywood under the ceiling, then acropropping it up to push the laths This technique can work for reparing a L&P ceiling - push it back temporarily and then pour extra bonding plaster on top to stabilise it... Something odd about the attributions here.... however, WRT repairing P&L ceilings, if the nails have let go (rust or pull-out) this is a not recommended repair. |
Chris Bacon wrote:
This technique can work for reparing a L&P ceiling - push it back temporarily and then pour extra bonding plaster on top to stabilise it... Something odd about the attributions here.... however, WRT repairing P&L ceilings, if the nails have let go (rust or pull-out) this is a not recommended repair. Should help to keep it in one lump when it falls down though ;-) -- Cheers, John. /================================================== ===============\ | Internode Ltd - http://www.internode.co.uk | |-----------------------------------------------------------------| | John Rumm - john(at)internode(dot)co(dot)uk | \================================================= ================/ |
John Rumm wrote:
Chris Bacon wrote: This technique can work for reparing a L&P ceiling - push it back temporarily and then pour extra bonding plaster on top to stabilise it... Something odd about the attributions here.... however, WRT repairing P&L ceilings, if the nails have let go (rust or pull-out) this is a not recommended repair. Should help to keep it in one lump when it falls down though ;-) Oooch. Might be a bit hard getting it out of the door (or down stairs!). |
All times are GMT +1. The time now is 03:15 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter