Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
I've decided to go ahead and make a replacement screw with a sliding
handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. (This isn't all I am doing, and its not "critical.") |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Bob La Londe" wrote in message
... I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. (This isn't all I am doing, and its not "critical.") Grade 5 and 8 bolts are high strength, readily available and not difficult to turn, mill or thread. |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
On 2019-05-20, Bob La Londe wrote:
I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. -- Remove oil spill source from e-mail Email: | (KV4PH) Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
On 5/20/2019 4:54 PM, DoN. Nichols wrote: On 2019-05-20, Bob La Londe
wrote: I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. 4140QT - QT means quenched and tempered. Its about the same hardness as 4140HT. TGP is "precision" ground. Actually from what I have been reading in between feeding the machines is that 1144 Stressproof(tm) is not ideal for cyclical loads like a bolt that is tightened and loosened repeatedly. For that they recommend a product called Fatigueproof(tm). 1144 Stressproof(tm) is great for a static load though. 4140QT is tough machining. Maybe a little more so than 304-316 stainless, but its machinable. I get the best finish with modestly large depth and width of cut on the lathe and a fresh insert. It will work harden faster than stainless if you screw around. This lathe has just enough power (3hp spindle motor) to do the job. The 4140QT is left over from jobs. Not something I bought just to have some. I bought "extra" just to have some. LOL. The 1144 I bought to just have some because its so darned easy to cut. I guess I'll be either using some of my stock of 4140QT or I'll do like Jim suggested and chase down a big bolt to machine down to the application. I've made tools out of all of the above. |
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
On Mon, 20 May 2019 18:41:15 -0700, Bob La Londe
wrote: On 5/20/2019 4:54 PM, DoN. Nichols wrote: On 2019-05-20, Bob La Londe wrote: I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. 4140QT - QT means quenched and tempered. Its about the same hardness as 4140HT. TGP is "precision" ground. Actually from what I have been reading in between feeding the machines is that 1144 Stressproof(tm) is not ideal for cyclical loads like a bolt that is tightened and loosened repeatedly. For that they recommend a product called Fatigueproof(tm). 1144 Stressproof(tm) is great for a static load though. 4140QT is tough machining. Maybe a little more so than 304-316 stainless, but its machinable. I get the best finish with modestly large depth and width of cut on the lathe and a fresh insert. It will work harden faster than stainless if you screw around. This lathe has just enough power (3hp spindle motor) to do the job. The 4140QT is left over from jobs. Not something I bought just to have some. I bought "extra" just to have some. LOL. The 1144 I bought to just have some because its so darned easy to cut. I guess I'll be either using some of my stock of 4140QT or I'll do like Jim suggested and chase down a big bolt to machine down to the application. I've made tools out of all of the above. I find Tractor Supply a good source for one or five grade five or grade eight bolts when I want to "invent" something! |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
On 5/20/2019 5:55 PM, Bob La Londe wrote:
... I am concerned about shearing off threads on an 1144 bolt, ... Reality check: how much torque/tension do you expect to put on this locking bolt? Unless your tightening wrench is going to be a foot or more long, the torque & tension is going to be small-ish. You could _probably_ use aluminum and not shear the threads. IMO |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Bob Engelhardt" wrote in message
... On 5/20/2019 5:55 PM, Bob La Londe wrote: ... I am concerned about shearing off threads on an 1144 bolt, ... Reality check: how much torque/tension do you expect to put on this locking bolt? Unless your tightening wrench is going to be a foot or more long, the torque & tension is going to be small-ish. You could _probably_ use aluminum and not shear the threads. IMO On my lathe one finger pushing a 4" wrench is enough. |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Gerry" wrote in message news
On Mon, 20 May 2019 18:41:15 -0700, Bob La Londe wrote: On 5/20/2019 4:54 PM, DoN. Nichols wrote: On 2019-05-20, Bob La Londe wrote: I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. 4140QT - QT means quenched and tempered. Its about the same hardness as 4140HT. TGP is "precision" ground. Actually from what I have been reading in between feeding the machines is that 1144 Stressproof(tm) is not ideal for cyclical loads like a bolt that is tightened and loosened repeatedly. For that they recommend a product called Fatigueproof(tm). 1144 Stressproof(tm) is great for a static load though. 4140QT is tough machining. Maybe a little more so than 304-316 stainless, but its machinable. I get the best finish with modestly large depth and width of cut on the lathe and a fresh insert. It will work harden faster than stainless if you screw around. This lathe has just enough power (3hp spindle motor) to do the job. The 4140QT is left over from jobs. Not something I bought just to have some. I bought "extra" just to have some. LOL. The 1144 I bought to just have some because its so darned easy to cut. I guess I'll be either using some of my stock of 4140QT or I'll do like Jim suggested and chase down a big bolt to machine down to the application. I've made tools out of all of the above. I find Tractor Supply a good source for one or five grade five or grade eight bolts when I want to "invent" something! ******* There is a place called Copper State bolt a lot closer to me than Tractor Supply and on the fasteners they stock they are always better priced than places like Tractor Supply, Cal-Ranch, and Home Depot. Also better quality and better selection. Hate might not be too strong of a word for the Hillman crap you find in most of those chain places. On the other hand when I am trying to finish something on Saturday afternoon I've been known to go to Lowes for a handful of grossly over priced stainless, or yes "Yesh" Tractor Supply or Cal-Ranch for a three point pin or bushing. Side Note: Cal-Ranch is kind of a pleasant surprise. Their website is total crap, but its quite the old fashion country hardware/general store. Guns in the back. Tools and hardware on one side, and clothing on the other... and its work clothing. Their fishing stuff is all kinda on the cheap side, but they have one. If you miss the old stores like Yellow Front, Fed-mart, or Fred's Corner Hardware they have done a decent job of capturing some of that for a chain store. They are bigger, have wider cleaner aisles, and a mix of decent and low end stuff, but the atmosphere is more pleasant and less institutional. And if I need a MIG welding tip on the weekend they have them. Not as cheap as 25 or 50 pack bags on Ebay, but about the same price as the store brand at your local welding supply store. The spray I use on my tractor came from them. |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Bob Engelhardt" wrote in message ... On 5/20/2019 5:55 PM, Bob La Londe wrote: ... I am concerned about shearing off threads on an 1144 bolt, ... Reality check: how much torque/tension do you expect to put on this locking bolt? Unless your tightening wrench is going to be a foot or more long, the torque & tension is going to be small-ish. You could _probably_ use aluminum and not shear the threads. IMO *** Um. No. But I get your point. LOL. Fair enough. I just really like this big chunk of Chinese cast iron, and if I'm going to modify it I want to make sure its a long term improvement. P.S. The wrench on top of my tool post is about a foot long though. |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Bob La Londe" wrote in message
... "Gerry" wrote in message news On Mon, 20 May 2019 18:41:15 -0700, Bob La Londe wrote: On 5/20/2019 4:54 PM, DoN. Nichols wrote: On 2019-05-20, Bob La Londe wrote: I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. 4140QT - QT means quenched and tempered. Its about the same hardness as 4140HT. TGP is "precision" ground. Actually from what I have been reading in between feeding the machines is that 1144 Stressproof(tm) is not ideal for cyclical loads like a bolt that is tightened and loosened repeatedly. For that they recommend a product called Fatigueproof(tm). 1144 Stressproof(tm) is great for a static load though. 4140QT is tough machining. Maybe a little more so than 304-316 stainless, but its machinable. I get the best finish with modestly large depth and width of cut on the lathe and a fresh insert. It will work harden faster than stainless if you screw around. This lathe has just enough power (3hp spindle motor) to do the job. The 4140QT is left over from jobs. Not something I bought just to have some. I bought "extra" just to have some. LOL. The 1144 I bought to just have some because its so darned easy to cut. I guess I'll be either using some of my stock of 4140QT or I'll do like Jim suggested and chase down a big bolt to machine down to the application. I've made tools out of all of the above. I find Tractor Supply a good source for one or five grade five or grade eight bolts when I want to "invent" something! ******* There is a place called Copper State bolt a lot closer to me than Tractor Supply and on the fasteners they stock they are always better priced than places like Tractor Supply, Cal-Ranch, and Home Depot. Also better quality and better selection. Hate might not be too strong of a word for the Hillman crap you find in most of those chain places. On the other hand when I am trying to finish something on Saturday afternoon I've been known to go to Lowes for a handful of grossly over priced stainless, or yes "Yesh" Tractor Supply or Cal-Ranch for a three point pin or bushing. Side Note: Cal-Ranch is kind of a pleasant surprise. Their website is total crap, but its quite the old fashion country hardware/general store. Guns in the back. Tools and hardware on one side, and clothing on the other... and its work clothing. Their fishing stuff is all kinda on the cheap side, but they have one. If you miss the old stores like Yellow Front, Fed-mart, or Fred's Corner Hardware they have done a decent job of capturing some of that for a chain store. They are bigger, have wider cleaner aisles, and a mix of decent and low end stuff, but the atmosphere is more pleasant and less institutional. And if I need a MIG welding tip on the weekend they have them. Not as cheap as 25 or 50 pack bags on Ebay, but about the same price as the store brand at your local welding supply store. The spray I use on my tractor came from them. That's great for you. We have a first class hardware store in southern NH https://www.yelp.com/biz/county-stores-milford-2 but there's no point suggesting it to readers outside this area. I try to recommend only things that can be bought new all over the USA, although my shop is equipped mostly with New England antiques from auctions and second-hand stores. |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Jim Wilkins" wrote in message ...
"Bob La Londe" wrote in message There is a place called Copper State bolt a lot closer to me than Tractor Supply and on the fasteners they stock they are always better priced than places like Tractor Supply, Cal-Ranch, and Home Depot. Also better quality and better selection. Hate might not be too strong of a word for the Hillman crap you find in most of those chain places. On the other hand when I am trying to finish something on Saturday afternoon I've been known to go to Lowes for a handful of grossly over priced stainless, or yes "Yesh" Tractor Supply or Cal-Ranch for a three point pin or bushing. Side Note: Cal-Ranch is kind of a pleasant surprise. Their website is total crap, but its quite the old fashion country hardware/general store. Guns in the back. Tools and hardware on one side, and clothing on the other... and its work clothing. Their fishing stuff is all kinda on the cheap side, but they have one. If you miss the old stores like Yellow Front, Fed-mart, or Fred's Corner Hardware they have done a decent job of capturing some of that for a chain store. They are bigger, have wider cleaner aisles, and a mix of decent and low end stuff, but the atmosphere is more pleasant and less institutional. And if I need a MIG welding tip on the weekend they have them. Not as cheap as 25 or 50 pack bags on Ebay, but about the same price as the store brand at your local welding supply store. The spray I use on my tractor came from them. That's great for you. We have a first class hardware store in southern NH https://www.yelp.com/biz/county-stores-milford-2 but there's no point suggesting it to readers outside this area. I try to recommend only things that can be bought new all over the USA, although my shop is equipped mostly with New England antiques from auctions and second-hand stores. ************* Cal-Ranch and Copperstate Bolt are both regional chains. Cal-Ranch is growing. Not sure about Copperstate. Copperstate does have a decent website. Not as good as McMaster, but decent. |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
Carriage Lock Screw Revisited
"Gerry" wrote in message news On Mon, 20 May 2019 18:41:15 -0700, Bob La Londe wrote: On 5/20/2019 4:54 PM, DoN. Nichols wrote: On 2019-05-20, Bob La Londe wrote: I've decided to go ahead and make a replacement screw with a sliding handle (like a vise handle), but also with a hex on top "just in case." This is a 14x40 lathe and there is plenty of clearance. Its not a giant, but its decent size and there is room to work on it. I have on 1144 stressproof, 4140QT, and cold rolled on hand. I have no issue using the 1144 or the cold rolled, but I can't pick up 4140(QT TGP) at a reasonable price locally. I hate to "burn it up" so to speak on personal projects. Given the ease with which 1144 machines I am concerned about shearing off threads on an 1144 bolt, but I have no issue using it because I can just go get some more if I need it. The cold rolled is really to soft IMO for making bolts. I know the 4140 is tough as heck, and would make the most durable bolt, but I hate to use it up if I don't have to. I've made bolts using 12L14 -- free machining steel -- and they have been strong enough for my needs. The 1144 sounds stronger, and the 4150QT may be more difficult to machine, depending. "QT" indicates some particular temper? (This isn't all I am doing, and its not "critical.") So play with what you have and see how it machines. Good Luck, DoN. 4140QT - QT means quenched and tempered. Its about the same hardness as 4140HT. TGP is "precision" ground. Actually from what I have been reading in between feeding the machines is that 1144 Stressproof(tm) is not ideal for cyclical loads like a bolt that is tightened and loosened repeatedly. For that they recommend a product called Fatigueproof(tm). 1144 Stressproof(tm) is great for a static load though. 4140QT is tough machining. Maybe a little more so than 304-316 stainless, but its machinable. I get the best finish with modestly large depth and width of cut on the lathe and a fresh insert. It will work harden faster than stainless if you screw around. This lathe has just enough power (3hp spindle motor) to do the job. The 4140QT is left over from jobs. Not something I bought just to have some. I bought "extra" just to have some. LOL. The 1144 I bought to just have some because its so darned easy to cut. I guess I'll be either using some of my stock of 4140QT or I'll do like Jim suggested and chase down a big bolt to machine down to the application. I've made tools out of all of the above. I find Tractor Supply a good source for one or five grade five or grade eight bolts when I want to "invent" something! ********** Sorry, what I should have said was: Thank you. They are a good option if one of the closers stores doesn't have what I need. Thanks for mentioning them. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Carriage lock screw - Any reason not to | Metalworking | |||
SB lathe q's (thread dial indic, chip tray, carriage lock) | Metalworking | |||
Craftsman RAS question; tightening the carriage lock tilts it... | Woodworking | |||
FA: Atlas 10" Turret Tailstock and Carriage Stop - NR | Metalworking | |||
does the carriage of a 10l southbend fit a 9 southbend | Metalworking |