Hydraulics related question
Β*Well the log splitter is mostly metal too ... ennyway , I have a minor
but irritating problem with the actuator valve . Pull to split and it goes great , pull the handle back to retract and it works great . As long as you hold it back . There's an internal detent there that's supposed to hold the handle in the retract position until the ram bottoms out , and it's not holding . Directly opposite the valve piston on the other end is a formed sheet metal cup device with a socket head cap screw sticking out , it has a jam nut to hold it adjusted ... I THINK this is where I'd adjust tension on that detent , but then again , I have zero experience with hydraulic valves . -- Snag Yes , I'm old and crochety - and armed . Get outta my woods ! |
Hydraulics related question
Terry Coombs wrote on 10/8/2018 3:45 PM:
Β*Well the log splitter is mostly metal too ... ennyway , I have a minor but irritating problem with the actuator valve . Pull to split and it goes great , pull the handle back to retract and it works great . As long as you hold it back . There's an internal detent there that's supposed to hold the handle in the retract position until the ram bottoms out , and it's not holding . Directly opposite the valve piston on the other end is a formed sheet metal cup device with a socket head cap screw sticking out , it has a jam nut to hold it adjusted ... I THINK this is where I'd adjust tension on that detent , but then again , I have zero experience with hydraulic valves . See if this helps: https://www.drpower.com/_drp/downloads/support/manuals/wds/279321E_Horizonta_Vertical_Log_Splitter_S-O_Manual_160606.pdf page 26 in the PDF: Adjusting the Handle Return Lever A Handle Return Lever is attached to the Valve Bracket to manually stop the Wedge when it is fully retracted.Β* The Lever may need to be adjusted if: - The Wedge is not retracting fully. - The Engine stalls and the Actuator Handle stays in the retract position with the Wedge is fully retracted. 1. Loosen the Jam Nut. 2. Adjust the Bolt. Screw Bolt into the Return Lever if the Operator lever is being pushed forward before fully retracting. Unscrew the Bolt from the Return Lever if the Operator lever is not being disengaged and the Engine is stalling. 3. When finished, hold the Bolt with the Wrench as you tighten the Jam Nut against the Lever using a Wrench.Β* Test and readjust as needed. |
Hydraulics related question
On 10/8/2018 4:45 PM, PM65C ¬ π΄πππππ πΎππππππ ¬ gAccu wrote:
Terry Coombs wrote on 10/8/2018 3:45 PM: Β*Well the log splitter is mostly metal too ... ennyway , I have a minor but irritating problem with the actuator valve . Pull to split and it goes great , pull the handle back to retract and it works great . As long as you hold it back . There's an internal detent there that's supposed to hold the handle in the retract position until the ram bottoms out , and it's not holding . Directly opposite the valve piston on the other end is a formed sheet metal cup device with a socket head cap screw sticking out , it has a jam nut to hold it adjusted ... I THINK this is where I'd adjust tension on that detent , but then again , I have zero experience with hydraulic valves . See if this helps: https://www.drpower.com/_drp/downloads/support/manuals/wds/279321E_Horizonta_Vertical_Log_Splitter_S-O_Manual_160606.pdf page 26 in the PDF: Adjusting the Handle Return Lever A Handle Return Lever is attached to the Valve Bracket to manually stop the Wedge when it is fully retracted.Β* The Lever may need to be adjusted if: - The Wedge is not retracting fully. - The Engine stalls and the Actuator Handle stays in the retract position with the Wedge is fully retracted. 1. Loosen the Jam Nut. 2. Adjust the Bolt. Screw Bolt into the Return Lever if the Operator lever is being pushed forward before fully retracting. Unscrew the Bolt from the Return Lever if the Operator lever is not being disengaged and the Engine is stalling. 3. When finished, hold the Bolt with the Wrench as you tighten the Jam Nut against the Lever using a Wrench.Β* Test and readjust as needed. Β* Thank you ! -- Snag Yes , I'm old and crochety - and armed . Get outta my woods ! |
All times are GMT +1. The time now is 03:55 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter