How Small Do You Grind ?
I started free hand grinding my own drill bits a few months ago. Not
out of choice, but out of necessity. Since I started doing it I have reground a fair number of them. Sometimes the same one two or three times in the same set of jobs. Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off. I bought a set of those some years back, but I've never seen them available singly. The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol. I actually make injectors .620 and sprues ..63, but sometimes you just have to brute force a solution. It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday. I just sharpen it right up and drop it back in its spot. Which brings me to the other size limit. The smallest I've reground so far was a #21. I picked that one to push the smaller size limit because I have several of them on hand. I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws. It came out ok. I'm not sure how much smaller I could grind free hand. Probably not much. I was squinting a bit at it and gritting my teeth. LOL. So how small of drill bits do you free hand regrind. I don't have a drill doctor or a Darex or a knockoff. Just a bench grinder. Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat. It would be really easy to overheat a tiny little drill bit. |
How Small Do You Grind ?
On 01/17/2018 06:58 PM, Bob La Londe wrote:
I started free hand grinding my own drill bits a few months ago.Â* Not out of choice, but out of necessity.Â* Since I started doing it I have reground a fair number of them.Â* Sometimes the same one two or three times in the same set of jobs.Â* Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off.Â* I bought a set of those some years back, but I've never seen them available singly.Â* The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol.Â* I actually make injectors .620 and sprues .63, but sometimes you just have to brute force a solution.Â* It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday.Â* I just sharpen it right up and drop it back in its spot.Â* Which brings me to the other size limit. The smallest I've reground so far was a #21.Â* I picked that one to push the smaller size limit because I have several of them on hand.Â* I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws.Â* It came out ok.Â* I'm not sure how much smaller I could grind free hand.Â* Probably not much. I was squinting a bit at it and gritting my teeth.Â* LOL.Â* So how small of drill bits do you free hand regrind.Â* I don't have a drill doctor or a Darex or a knockoff.Â* Just a bench grinder.Â* Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat.Â* It would be really easy to overheat a tiny little drill bit. I got a Drill Doctor at a metal club swap meet a few years ago. If you follow the directions, they work pretty well. I think the lower limit on them is 3/16" or maybe 1/8" My attempts at free-handing a drill bit were disappointing at best. BobH |
How Small Do You Grind ?
On Wed, 17 Jan 2018 18:58:48 -0700, Bob La Londe
wrote: I started free hand grinding my own drill bits a few months ago. Not out of choice, but out of necessity. Since I started doing it I have reground a fair number of them. Sometimes the same one two or three times in the same set of jobs. Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off. I bought a set of those some years back, but I've never seen them available singly. The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol. I actually make injectors .620 and sprues .63, but sometimes you just have to brute force a solution. It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday. I just sharpen it right up and drop it back in its spot. Which brings me to the other size limit. The smallest I've reground so far was a #21. I picked that one to push the smaller size limit because I have several of them on hand. I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws. It came out ok. I'm not sure how much smaller I could grind free hand. Probably not much. I was squinting a bit at it and gritting my teeth. LOL. So how small of drill bits do you free hand regrind. I don't have a drill doctor or a Darex or a knockoff. Just a bench grinder. Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat. It would be really easy to overheat a tiny little drill bit. The smaller drills..for me...are easier ground on the typical 1x40 belt sander. I DO have a Darex M500 hummm 2 of them actually..and a couple of Drill Doctors..and I still tend to use the wheel or belt sander...its fastar and quicker than ****ing with the machines. Now if I have a handful of bits to do..yeah..the machines get it..but for onesies and twosies...grinder or belt sander --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
How Small Do You Grind ?
BobH wrote:
On 01/17/2018 06:58 PM, Bob La Londe wrote: I started free hand grinding my own drill bits a few months ago.? Not out of choice, but out of necessity.? Since I started doing it I have reground a fair number of them.? Sometimes the same one two or three times in the same set of jobs.? Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off.? I bought a set of those some years back, but I've never seen them available singly.? The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol.? I actually make injectors .620 and sprues .63, but sometimes you just have to brute force a solution.? It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday.? I just sharpen it right up and drop it back in its spot.? Which brings me to the other size limit. The smallest I've reground so far was a #21.? I picked that one to push the smaller size limit because I have several of them on hand.? I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws.? It came out ok.? I'm not sure how much smaller I could grind free hand.? Probably not much. I was squinting a bit at it and gritting my teeth.? LOL.? So how small of drill bits do you free hand regrind.? I don't have a drill doctor or a Darex or a knockoff.? Just a bench grinder.? Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat.? It would be really easy to overheat a tiny little drill bit. I got a Drill Doctor at a metal club swap meet a few years ago. If you follow the directions, they work pretty well. The instructions are pretty weak at best, and you can end up with some really weird an nonfunctional bits even if you "follow the instructions". At least you can see if they're all jacked up and just keep trying with different amounts of "touch" until they look about right. I think the lower limit on them is 3/16" or maybe 1/8" I got some 1/8" bits working again with the drill doctor. Never bothered with smaller ones yet, although they will chuck up OK. My attempts at free-handing a drill bit were disappointing at best. Same here. The drill doctor hasn't paid for itself by any means yet but the box of trashed bits is now a box of bits that just don't belong to an index, so that's handy. |
How Small Do You Grind ?
On Wednesday, January 17, 2018 at 7:58:50 PM UTC-6, Bob La Londe wrote:
I started free hand grinding my own drill bits a few months ago. Not out of choice, but out of necessity. Since I started doing it I have reground a fair number of them. Sometimes the same one two or three times in the same set of jobs. Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off. I bought a set of those some years back, but I've never seen them available singly. The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol. I actually make injectors .620 and sprues .63, but sometimes you just have to brute force a solution. It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday. I just sharpen it right up and drop it back in its spot. Which brings me to the other size limit. The smallest I've reground so far was a #21. I picked that one to push the smaller size limit because I have several of them on hand. I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws. It came out ok. I'm not sure how much smaller I could grind free hand. Probably not much. I was squinting a bit at it and gritting my teeth. LOL. So how small of drill bits do you free hand regrind. I don't have a drill doctor or a Darex or a knockoff. Just a bench grinder. Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat. It would be really easy to overheat a tiny little drill bit. Back in the day, just for fun, I could grind a .0625 to cut onsize, then split the point. |
How Small Do You Grind ?
On Wed, 24 Jan 2018 05:38:22 +0000 (UTC), Cydrome Leader
wrote: BobH wrote: On 01/17/2018 06:58 PM, Bob La Londe wrote: I started free hand grinding my own drill bits a few months ago.? Not out of choice, but out of necessity.? Since I started doing it I have reground a fair number of them.? Sometimes the same one two or three times in the same set of jobs.? Now I have old eyes, but my glasses are pretty good, and I have a magnifier lamp I swing over my bench grinder. It allows me to free hand better than I ever thought I would be able to. I've also resharpened some of my stub length Silver and Deming bits. That's where it really pays off.? I bought a set of those some years back, but I've never seen them available singly.? The 5/8 took quite a beating over the years since its the standard injection port size for hand injecting plastisol.? I actually make injectors .620 and sprues .63, but sometimes you just have to brute force a solution.? It was nice to finally be able to just sharpen it right up. No more piles of drill bits to be sharpened someday.? I just sharpen it right up and drop it back in its spot.? Which brings me to the other size limit. The smallest I've reground so far was a #21.? I picked that one to push the smaller size limit because I have several of them on hand.? I ordered a half dozen of them once from McMaster in stub screw machine length to drill molds for 10-32 clamping screws.? It came out ok.? I'm not sure how much smaller I could grind free hand.? Probably not much. I was squinting a bit at it and gritting my teeth.? LOL.? So how small of drill bits do you free hand regrind.? I don't have a drill doctor or a Darex or a knockoff.? Just a bench grinder.? Well a couple of them and a small belt grinder now. I think one of the limits is grit size, but another would be heat.? It would be really easy to overheat a tiny little drill bit. I got a Drill Doctor at a metal club swap meet a few years ago. If you follow the directions, they work pretty well. The instructions are pretty weak at best, and you can end up with some really weird an nonfunctional bits even if you "follow the instructions". At least you can see if they're all jacked up and just keep trying with different amounts of "touch" until they look about right. I think the lower limit on them is 3/16" or maybe 1/8" I got some 1/8" bits working again with the drill doctor. Never bothered with smaller ones yet, although they will chuck up OK. My attempts at free-handing a drill bit were disappointing at best. Same here. The drill doctor hasn't paid for itself by any means yet but the box of trashed bits is now a box of bits that just don't belong to an index, so that's handy. I've been quite happy with my Drill Doctor and have had some success with 3/32" |
How Small Do You Grind ?
On Thursday, January 18, 2018 at 1:04:38 AM UTC-8, Gunner Asch wrote:
On Wed, 17 Jan 2018 18:58:48 -0700, Bob La Londe wrote: I started free hand grinding my own drill bits... The smallest I've reground so far was a #21. The smaller drills..for me...are easier ground on the typical 1x40 belt sander. I had a production problem that needed #61 drills, and (before we switched to HD cobalt) dulled 'em fast. So, when we got to the bottom of our stock, the (real machinists) set us up on the drill sharpener (Darex, I recall). There were collets for each drill size, and it did a good job. But hearing that 'the smaller drills' get sharpened on the belt sander, I have to laugh. That wouldn't have worked for me. |
All times are GMT +1. The time now is 03:59 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter