Anybody know Bridgeport power feeds?
 

The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?
Thanks,
Eric

Anybody know Bridgeport power feeds?
 

On Mon, 08 Jan 2018 11:20:16 -0800, wrote:

The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?
Thanks,
Eric


Pretty much it. Table feed or head feed?

Gunner

---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

Anybody know Bridgeport power feeds?
 

On 2018-01-08, wrote:
The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?

How about checking whether the leadscrew has a bit of end play.
If it moves, it carries its gear with it. Likely the bearings at the
end of the table just before the power feed and the crank.

Good Luck,
DoN.

--
Remove oil spill source from e-mail
Email: | (KV4PH) Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---

Anybody know Bridgeport power feeds?
 

On 10 Jan 2018 04:26:59 GMT, "DoN. Nichols"
wrote:

On 2018-01-08, wrote:
The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?

How about checking whether the leadscrew has a bit of end play.
If it moves, it carries its gear with it. Likely the bearings at the
end of the table just before the power feed and the crank.

Good Luck,
DoN.

He hasnt answered if its spindle or table powerfeed yet....


---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus

Anybody know Bridgeport power feeds?
 

On 10 Jan 2018 04:26:59 GMT, "DoN. Nichols"
wrote:

On 2018-01-08, wrote:
The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?

How about checking whether the leadscrew has a bit of end play.
If it moves, it carries its gear with it. Likely the bearings at the
end of the table just before the power feed and the crank.

Good Luck,
DoN.
Thanks DoN,
I'll take a look at that first once the cover is removed.
Eric

Anybody know Bridgeport power feeds?
 

On Wed, 10 Jan 2018 09:15:02 -0800, wrote:

On 10 Jan 2018 04:26:59 GMT, "DoN. Nichols"
wrote:

On 2018-01-08, wrote:
The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?

How about checking whether the leadscrew has a bit of end play.
If it moves, it carries its gear with it. Likely the bearings at the
end of the table just before the power feed and the crank.

Good Luck,
DoN.
Thanks DoN,
I'll take a look at that first once the cover is removed.
Eric

Bridgports use a preloaded pair of bearings at the left end of the
screw to handle the screw's thrust. The bearing on the right
(presumably where the power feed is mounted) floats axially.

Many clones (including my Supermax) have a single bearing at each end
with the preload carried by tension in the screw. The Bridgeport
arrangement is more reliable.

The Servo brand power feeds rely on the screw to maintain the position
of the miter gear. Not sure if this is true of Bridgeport's feeds. I
have a ca. 1981 BP manual with an exploded parts diagram, and it looks
as though the miter gear's axial position is independent of the screw,
but it's not entirely clear.

--
Ned Simmons

Anybody know Bridgeport power feeds?
 

On Wed, 10 Jan 2018 13:42:50 -0500, Ned Simmons
wrote:

On Wed, 10 Jan 2018 09:15:02 -0800, wrote:

On 10 Jan 2018 04:26:59 GMT, "DoN. Nichols"
wrote:

On 2018-01-08, wrote:
The power feed on my Bridgeport mill has started making a bad noise
when moving in one direction. The mill and power feed I bought new in
1981 and the power feed is the stock factory installed Bridgeport
brand power feed. When moving in one direction the power feed sounds
like it always has but when moving in the other it sounds like badly
meshing miter gears. Which is probably what the noise is. Maybe a gear
has become loose on its shaft and in one direction sounds good because
it is being pushed against some sort of stop which keeps it properly
engaged. But when the gear is spinning in the opposite direction it
moves out of proper engagement. Anyhow, before I take the drive apart
it would be nice to know if there is anything else I should be looking
for. Anybody know?

How about checking whether the leadscrew has a bit of end play.
If it moves, it carries its gear with it. Likely the bearings at the
end of the table just before the power feed and the crank.

Good Luck,
DoN.
Thanks DoN,
I'll take a look at that first once the cover is removed.
Eric

Bridgports use a preloaded pair of bearings at the left end of the
screw to handle the screw's thrust. The bearing on the right
(presumably where the power feed is mounted) floats axially.

Many clones (including my Supermax) have a single bearing at each end
with the preload carried by tension in the screw. The Bridgeport
arrangement is more reliable.

The Servo brand power feeds rely on the screw to maintain the position
of the miter gear. Not sure if this is true of Bridgeport's feeds. I
have a ca. 1981 BP manual with an exploded parts diagram, and it looks
as though the miter gear's axial position is independent of the screw,
but it's not entirely clear.
Thanks Everyone for your replies. I just finished the fix. The big
miter gear had backed off a tiny amount. I guess that's OK after 37
years of use. Like other folks I had added a drain hole to the drive.
I was truly surprised to find no drain hole for the drive gearbox.
Having to let the oil drain out around the cover is stupid.
Eric