FS -- 7.5 HP, MT5 Drill Press
 

http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg

FS -- 7.5 HP, MT5 Drill Press
 

On 2013-08-19, Ignoramus16764 wrote:
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg

Located near Chicago, made by English and Miller, offered here for
only a few days, as I have a standing offer on it.

i

FS -- 7.5 HP, MT5 Drill Press
 

On Mon, 19 Aug 2013 10:39:39 -0500, Ignoramus16764
wrote:

http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg

How many power feed ranges are there?


"There are no leftists in mainstream American politics.

Just two right wing parties, one hard right and one softer."
Christopher A. Lee, 8/18/2013

FS -- 7.5 HP, MT5 Drill Press
 

On Mon, 19 Aug 2013 10:39:39 -0500, Ignoramus16764
wrote:

http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg

$25 and you haul, right? sigh


http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg

That spindle is hung like a horse. Checked the wobble or runout yet?
Judging by the label on the right, someone gave it a Big Al Rebuild at
some point in the past.


http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg

Dayum! What took that chunk out of the t-slots just on the other side
of the center cutout? Did someone crank a clamp down with a 3/4"
impact or stick a large diameter drill bit in a piece which came
loose? That's a couple/three inches of hole there, innit?



--
Truth loves to go naked.
--Dr. Thomas Fuller, Gnomologia, 1732

FS -- 7.5 HP, MT5 Drill Press
 

On 2013-08-20, Larry Jaques wrote:
On Mon, 19 Aug 2013 10:39:39 -0500, Ignoramus16764
wrote:

http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg

$25 and you haul, right? sigh


http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg

That spindle is hung like a horse. Checked the wobble or runout yet?
Judging by the label on the right, someone gave it a Big Al Rebuild at
some point in the past.


http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg

Dayum! What took that chunk out of the t-slots just on the other side
of the center cutout? Did someone crank a clamp down with a 3/4"
impact or stick a large diameter drill bit in a piece which came
loose? That's a couple/three inches of hole there, innit?

Maybe one of those MT5 drills got caught in the material.

This press is enormous. Probably obsolete and superseded by CMC
milling.

i

FS -- 7.5 HP, MT5 Drill Press
 

Tomorrow is the day when it goes bye-bye to a scrap yard.

i

On 2013-08-19, Ignoramus16764 wrote:
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0001.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0016.jpg
http://yabe.chudov.com/HUGE-MT5-7-5-...12105-0003.jpg