Soldering to steel (fuel tank)
I am trying to solder a brass fitting to the fuel tank.
By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? i |
Soldering to steel (fuel tank)
"Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? Silver solder would probably be my first choice -- |
Soldering to steel (fuel tank)
On 2011-07-14, PrecisionmachinisT wrote:
"Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? Silver solder would probably be my first choice OK, will try! 15%? i |
Soldering to steel (fuel tank)
"Ignoramus23641" wrote in message ... On 2011-07-14, PrecisionmachinisT wrote: "Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? Silver solder would probably be my first choice OK, will try! 15%? Damn that was fast !!! I'm not an expert on brazing, welding etc but probably 15% would be fine --others might chime in ... -- |
Soldering to steel (fuel tank)
"Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. Try straight hydrochloric acid, in standard muriatic dilution. That's my last resort for soldering steel. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? Yes. And even silver braze can be tricky with brass. You have to be *very* careful, or the brass goes "slump...." IOW, is the melting point of the brass brazing material lower than that of solid brass? It depends. Common brass/bronze brazing rod can be straight yellow brass, although most of them contain other stuff. You want an alloy made for brazing brass, like Silvaloy, which typically contain some silver. Don't overheat or you'll be sorry (I have, for example, some very curious-looking shop-made yellow brass thumbscrews, with brass heads on steel screws. They're all wobbly from silver-brazing in a hurry and overheating them.) But you should be able to solder that steel. Have you tried scratch-fluzing it with a throwaway stainless or plain-steel brush? It works. Then throw away the brush. -- Ed Huntress i |
Soldering to steel (fuel tank)
"Ed Huntress" wrote in message ... "Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. Try straight hydrochloric acid, in standard muriatic dilution. That's my last resort for soldering steel. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? Yes. And even silver braze can be tricky with brass. You have to be *very* careful, or the brass goes "slump...." IOW, is the melting point of the brass brazing material lower than that of solid brass? It depends. Common brass/bronze brazing rod can be straight yellow brass, although most of them contain other stuff. You want an alloy made for brazing brass, like Silvaloy, which typically contain some silver. Don't overheat or you'll be sorry (I have, for example, some very curious-looking shop-made yellow brass thumbscrews, with brass heads on steel screws. They're all wobbly from silver-brazing in a hurry and overheating them.) But you should be able to solder that steel. Have you tried scratch-fluzing it with a throwaway stainless or plain-steel brush? It works. Then throw away the brush. Personally, I think he's probably not getting the steel hot enough because all the water in the tank is sucking away the heat. -- |
Soldering to steel (fuel tank)
On 07/13/2011 08:28 PM, PrecisionmachinisT wrote:
"Ed wrote in message ... id wrote in message ... I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. Try straight hydrochloric acid, in standard muriatic dilution. That's my last resort for soldering steel. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? Yes. And even silver braze can be tricky with brass. You have to be *very* careful, or the brass goes "slump...." IOW, is the melting point of the brass brazing material lower than that of solid brass? It depends. Common brass/bronze brazing rod can be straight yellow brass, although most of them contain other stuff. You want an alloy made for brazing brass, like Silvaloy, which typically contain some silver. Don't overheat or you'll be sorry (I have, for example, some very curious-looking shop-made yellow brass thumbscrews, with brass heads on steel screws. They're all wobbly from silver-brazing in a hurry and overheating them.) But you should be able to solder that steel. Have you tried scratch-fluzing it with a throwaway stainless or plain-steel brush? It works. Then throw away the brush. Personally, I think he's probably not getting the steel hot enough because all the water in the tank is sucking away the heat. Or he's overheating it and oxidizing the surface before the solder gets a chance to stick. There's three things you need to make sure of before you try to solder something (or braze, for that matter). It needs to be clean. And it needs to be clean. And, when you get that done, it needs to be clean. Making sure it's clean doesn't hurt, either. -- Tim Wescott Wescott Design Services http://www.wescottdesign.com Do you need to implement control loops in software? "Applied Control Theory for Embedded Systems" was written for you. See details at http://www.wescottdesign.com/actfes/actfes.html |
Soldering to steel (fuel tank)
On 07/13/2011 10:32 PM, Tim Wescott wrote:
There's three things you need to make sure of before you try to solder something (or braze, for that matter). It needs to be clean. And it needs to be clean. And, when you get that done, it needs to be clean. Making sure it's clean doesn't hurt, either. "Tin" the steel with solder, all by itself. Insert brass/copper fitting. Heat assembled connection and solder it together. Plus, what Tim said. technomaNge -- Learning to ignore things is one of the great paths to inner peace. -- Robert J. Sawyer With that in mind, I'd like to thank all those assholes in my killfile. |
Soldering to steel (fuel tank)
OK, I am done. I used a steel fitting on steel tank, and brazed that
stuff with brass brazing rod. The result is not pretty, but completely functional. i |
Soldering to steel (fuel tank)
Ignoramus23641 wrote:
OK, I am done. I used a steel fitting on steel tank, and brazed that stuff with brass brazing rod. The result is not pretty, but completely functional. i Pics, or it didn't happen! -- Richard Lamb http://www.home.earthlink.net/~cavelamb http://www.home.earthlink.net/~sv_temptress |
Soldering to steel (fuel tank)
"Ignoramus23641" wrote in message ... OK, I am done. I used a steel fitting on steel tank, and brazed that stuff with brass brazing rod. The result is not pretty, but completely functional. Bravely done.... Or, at the least that's what appears to have been printed on the underside of this here bottlecap. Cheers... -- |
Soldering to steel (fuel tank)
On Jul 14, 12:44*pm, Ignoramus23641 ignoramus23...@NOSPAM.
23641.invalid wrote: I am trying to solder a brass fitting to the fuel tank. Easy as - get the right tool for the job, in this case a very large plumbers soldering iron - the type that was at least 100 watts, with a 1 inch diameter bit in it that was the massive heat reservoir needed. (There was even a pump up gas fired one for the real heavy duty stuff.....) Gas axes are iffy, unless your pretty good at brazing - I aint, but soldering works fine long term on the very few that I have done. Andrew VK3BFA. |
Soldering to steel (fuel tank)
"Ignoramus23641" wrote in message ... I am trying to solder a brass fitting to the fuel tank. I'd ask a couple of questions: -What was there before you started this process? If there was any other kind of material, some remnants could be fused into the area you are trying to tin. especially epoxies. -What kind of solder are you trying currently? If it is soft solder, does it have a flux core, and, if so what kind? (Acid or Resin)? or ? If you using "electronic" solder, it may be a resin (rosin core) flux. I'd certainly go with acid core for this application. I usually keep liquid or semi liquid fluxes of both type around. -Can you get tinning to occur on other pieces of sheet metal? 1. The area to be "tinned" needs to be bright and shiny, and it should be cleaned immediately before attempting to heat/tin it. 2. Use a soft flame. It is very easy to overheat something as thin as a fuel tank. One instant of too much heat and it's all over, until you re-prepare the surface. 3. If you go with a silver solder, make sure you get a flux that matches the temp range of the solder. 4. Years ago, we had to soft solder electrical wires onto steel leads from high pressure liquid sensors. The only way we could get tinning to occur was to use sal-ammoniac as a flux(sp?). I personally still like to use heavy soldering coppers (soldering irons to the rest of you) for such work. I heat them with a propane torch until the solder to be used melts freely, then use the heat from them, (properly tinned, of course) to transfer the heat to the work. You'd be surprised at how effective this approach is. This way, there is NO chance of overheating the work. I like to collect old soldering "irons" for just this use. Note that, in their day, they were usually sold in pairs. One would be being reheated while the other one was in use. Let us know what eventually works out for you. Pete Stanaitis --------------- |
Soldering to steel (fuel tank)
Ignoramus23641 wrote:
OK, I am done. I used a steel fitting on steel tank, and brazed that stuff with brass brazing rod. The result is not pretty, but completely functional. If you didn't have the steel fitting, you could have used the brass and avoided melting it by brazing a coating on the steel and then soft soldering the brass fitting to the coating. Pretty is nice, but functional is much better. Bob |
Soldering to steel (fuel tank)
On Jul 13, 8:44*pm, Ignoramus23641 ignoramus23...@NOSPAM.
23641.invalid wrote: I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. * * * *http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? i For steel, you need acid flux, either the paste stuff or liquid, see the hardware store. With that much surface area, you're going to need a LOT of heat, unless you've a got really massive electric iron, a torch head with a big soldering tip will be needed. For that sort of work, I favor the old soldering coppers, those were designed for sheetmetal work. Used a kerosene or gasoline blowtorch to heat them up, propane works if you've got to be more modern. Applying a torch flame to solder, even with flux, will give the results you describe, just rolls up in little balls and doesn't stick. Tin the area first, then the fitting, then sweat the two together. You have to have more heat going into the area than flows out. Get the flux residue off afterwards, it'll rust the steel. Baking soda solution should neutralize things. If you're going to try brazing, use a filler with a high silver content, it'll flow better and not take so much heat to melt it. If you've got ANY lead-based solder stuck on the parts, you need to get it off first. Stan |
Soldering to steel (fuel tank)
On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641
wrote: I am trying to solder a brass fitting to the fuel tank. Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. i You've already accomplished what you wanted to do, but I'll mention that I've experienced this before too. What has worked on one or two occasions was to scratch the solder into the steel with a screwdriver, coarse steel wool, sandpaper or the tip of the soldering iron while all was still fluid. That made the solder stick to the steel, "tinning" the steel first. The flux that I use is made by Kester and is a pink liquid. I bought it at a yard sale years ago. I have no idea if it's still available. RWL |
Soldering to steel (fuel tank)
GeoLane at PTD dot NET wrote in message ... On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641 wrote: I am trying to solder a brass fitting to the fuel tank. Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. i You've already accomplished what you wanted to do, but I'll mention that I've experienced this before too. What has worked on one or two occasions was to scratch the solder into the steel with a screwdriver, coarse steel wool, sandpaper or the tip of the soldering iron while all was still fluid. That made the solder stick to the steel, "tinning" the steel first. A steel or stainless brush is great for this. It also solves a lot of problems with soldering unknown aluminum alloys. The flux that I use is made by Kester and is a pink liquid. I bought it at a yard sale years ago. I have no idea if it's still available. RWL |
Soldering to steel (fuel tank)
On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641
wrote: I am trying to solder a brass fitting to the fuel tank. By the way, the tank did not explode. I filled it with water, leaving 3/4 inch or so of air above the water. I stuck a torch into it, and nothing happened, as I predicted. http://www.youtube.com/watch?v=luubA9ELfwY Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. I wonder if I should, instead, try to use brass brazing material (I have brass brazing sticks with flux on them). If I do so, trying to braze a brass fitting with brass braze, would the brass fitting melt? IOW, is the melting point of the brass brazing material lower than that of solid brass? i You need good flux to solder the steel. It needs to be CLEAN Brazing works a bit better, but it still needs to be CLEAN. There are quite a few different kinds of "brazing rod" - some of which melt hotter than others. Same with solders. And you need to get the METAL hot enough to melt the solder (or braze) - which requires a LOT of heat if the tank is full of water - which is why I use CO2. |
Soldering to steel (fuel tank)
On Thu, 14 Jul 2011 17:26:51 -0400, Bob Engelhardt
wrote: Ignoramus23641 wrote: OK, I am done. I used a steel fitting on steel tank, and brazed that stuff with brass brazing rod. The result is not pretty, but completely functional. If you didn't have the steel fitting, you could have used the brass and avoided melting it by brazing a coating on the steel and then soft soldering the brass fitting to the coating. Pretty is nice, but functional is much better. Bob "first you make it work, THEN you make it pretty" |
Soldering to steel (fuel tank)
GeoLane at PTD dot NET wrote: On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641 wrote: I am trying to solder a brass fitting to the fuel tank. Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. i You've already accomplished what you wanted to do, but I'll mention that I've experienced this before too. What has worked on one or two occasions was to scratch the solder into the steel with a screwdriver, coarse steel wool, sandpaper or the tip of the soldering iron while all was still fluid. That made the solder stick to the steel, "tinning" the steel first. The flux that I use is made by Kester and is a pink liquid. I bought it at a yard sale years ago. I have no idea if it's still available. It's called, 'Ruby Fluid', and was sold for copper plumbing: http://rubyfluidflux.com/uploads/New_Rubyfluid_Flux_Product_Sheet_with_THEIR_images _2.pdf http://i53.tinypic.com/2myoshe.jpg kester has dropped all pluming solders & fluxes from their website, but that was a common product. It's harder to find these days, since they switched to lead free solder on water lines, but some stores still sell small botles of it for under $5. -- It's easy to think outside the box, when you have a cutting torch. |
Soldering to steel (fuel tank)
"Michael A. Terrell" wrote: GeoLane at PTD dot NET wrote: On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641 wrote: I am trying to solder a brass fitting to the fuel tank. Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. i You've already accomplished what you wanted to do, but I'll mention that I've experienced this before too. What has worked on one or two occasions was to scratch the solder into the steel with a screwdriver, coarse steel wool, sandpaper or the tip of the soldering iron while all was still fluid. That made the solder stick to the steel, "tinning" the steel first. The flux that I use is made by Kester and is a pink liquid. I bought it at a yard sale years ago. I have no idea if it's still available. It's called, 'Ruby Fluid', and was sold for copper plumbing: http://rubyfluidflux.com/uploads/New_Rubyfluid_Flux_Product_Sheet_with_THEIR_images _2.pdf http://i53.tinypic.com/2myoshe.jpg Kester has dropped all pluming solders & fluxes from their website, but that was a common product. It's harder to find these days, since they switched to lead free solder on water lines, but some stores still sell small botles of it for under $5. http://www.amazon.com/Ruby-Chemical-1PT-Liquid-Rubyfluid/dp/B000CNMHJW/ref=pd_cp_hi_0 $5.81 for a pint. -- It's easy to think outside the box, when you have a cutting torch. |
Soldering to steel (fuel tank)
On Wed, 13 Jul 2011 23:52:58 -0500
Ignoramus23641 wrote: OK, I am done. I used a steel fitting on steel tank, and brazed that stuff with brass brazing rod. The result is not pretty, but completely functional. i Did you do a pressure test? I've had several gas tank braze jobs that looked beautiful but leaked right through the brazed area. A bit of air pressure, some soapy water and watch for bubbles... -- Leon Fisk Grand Rapids MI/Zone 5b Remove no.spam for email |
Soldering to steel (fuel tank)
On Thu, 14 Jul 2011 21:48:54 -0400, GeoLane at PTD dot NET GeoLane at
PTD dot NET wrote: On Wed, 13 Jul 2011 21:44:55 -0500, Ignoramus23641 wrote: I am trying to solder a brass fitting to the fuel tank. Anyway, the tank, while not exploding, just does not, flat out, accept solder. The solder just balls on top of the steel, does NOT wet it at all, and rolls away when exposed to the gases from the propane torch. I tried a couple of fluxes and nothing helps. i You've already accomplished what you wanted to do, but I'll mention that I've experienced this before too. What has worked on one or two occasions was to scratch the solder into the steel with a screwdriver, coarse steel wool, sandpaper or the tip of the soldering iron while all was still fluid. That made the solder stick to the steel, "tinning" the steel first. The flux that I use is made by Kester and is a pink liquid. I bought it at a yard sale years ago. I have no idea if it's still available. RWL Zinc Chloride is about the best for steel. Hydrochloric acid, cut with as much zinc as it will disolve. It's green and nasty. |
All times are GMT +1. The time now is 01:28 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter