Purchased the Leblond
Whadya think ?
http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. |
Purchased the Leblond
On Fri, 11 Dec 2009 16:13:29 -0800, azotic wrote:
Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. I'm jealous. That's less than I spent on my Smithy, and somehow I think it's a much better lathe. -- www.wescottdesign.com |
Purchased the Leblond
"azotic" wrote:
Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. Assume ways are good, no damaged gears, ect, I think you did just fine. There are three change gears for cutting metric required on the one I use (two missing) did you get them? Actually, it probably has replaceable ways but I don't want to even think of what the price is for those. It has been 4 years but we bought a change gear case housing and some of the qc gears after our tool room guy had a really bad day. Unless something has happened in the last 4 years, repair parts are available. Hold on to your wallet though, just like my Clausing. Also, the tag is obscuring where the drive reverse lever should be on the apron, do you have one? Assuming all is go on my questions, then you really suck! ;) Wes -- "Additionally as a security officer, I carry a gun to protect government officials but my life isn't worth protecting at home in their eyes." Dick Anthony Heller |
Purchased the Leblond
On 2009-12-12, azotic wrote:
Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i |
Purchased the Leblond
Even if this is just a basic lathe, it is a good deal. If the condition is good and you have some tooling, you stole it. If it
has a taper attachment as well, the guy that sold it for that price is an idiot. Steve "azotic" wrote in message ... Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. |
Purchased the Leblond
"Ignoramus20864" wrote in message ... On 2009-12-12, azotic wrote: Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i I checked ebay and they are trying to get $6-7K for that machine. Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. Anyway now i can make some .0001" tolerance candle stick holders for christmas gifts.... Best Regards Tom. |
Purchased the Leblond
On 2009-12-12, azotic wrote:
"Ignoramus20864" wrote in message ... On 2009-12-12, azotic wrote: Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i I checked ebay and they are trying to get $6-7K for that machine. Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. Anyway now i can make some .0001" tolerance candle stick holders for christmas gifts.... You stole it and I HATE YOU. i |
Purchased the Leblond
On 2009-12-12, Ignoramus20864 wrote:
On 2009-12-12, azotic wrote: "Ignoramus20864" wrote in message ... On 2009-12-12, azotic wrote: Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i I checked ebay and they are trying to get $6-7K for that machine. Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. Anyway now i can make some .0001" tolerance candle stick holders for christmas gifts.... You stole it and I HATE YOU. i And post more pictures of this thing... i |
Purchased the Leblond
On Dec 11, 10:18�pm, "azotic" wrote:
"Ignoramus20864" wrote in message ... On 2009-12-12, azotic wrote: Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i I checked ebay and they are trying to get $6-7K for that machine. Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. Anyway now i can make some .0001" tolerance candle stick holders for christmas gifts.... Best Regards Tom. Tom A nice lathe to have. And with enough tooling to get going. So pricing is good. So just be watchful and soon you will have all you need for it. When I finally bought my lathe I was tired and fed up with looking. I did not have enough space for it but coupled with being tired of fooling around I threw out a binch of stuff to make room for it. I just sucked up the money thing and did some work for somebody to pay the bill. Don'rt even remember who it was. Bob AZ Bob AZ |
Purchased the Leblond
"azotic" wrote in message ... Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. Tom, If the lathe has no issues, you did just fine. I'm not a LeBlond fan, but they build a very nice and rugged machine that is very capable of serious work. I've operated a few of them in my years, including a sliding gap bed with 48" swing. Harold |
Purchased the Leblond
"azotic" wrote in message ... "Ignoramus20864" wrote in message ... On 2009-12-12, azotic wrote: Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Most likely it is a good deal. i I checked ebay and they are trying to get $6-7K for that machine. Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. Anyway now i can make some .0001" tolerance candle stick holders for christmas gifts.... Best Regards Tom. Having just read your comments about how the lathe is tooled, quite frankly, you stole it. Good on ya, Tom. Harold |
Purchased the Leblond
"azotic" wrote:
Luckliy this one has the metric thread cutting gears, face plate, 3 & 4 Jaw chucks, 5c collet adaptor, aloris tool post with a bunch of holders, taper attachment and original manual. This wasi n a tool & die, mold shop. The owner said they bought it new. Did a couple of test cuts and its a tight machine as one would expect on a machine with hardend ways. This is definitely a gloat. At least you didn't get a steady and follow rest or we would all be suicidal. ;) Wes -- "Additionally as a security officer, I carry a gun to protect government officials but my life isn't worth protecting at home in their eyes." Dick Anthony Heller |
Purchased the Leblond
On Fri, 11 Dec 2009 16:13:29 -0800, "azotic" wrote:
Whadya think ? http://members.cox.net/azotic/Leblond.jpg is $1500.00 a good price ? Best Regards Tom. Considering that I just brokered one for $3500 and the guy was happy as hell....ah...yes....it was a good price G Gunner "First Law of Leftist Debate The more you present a leftist with factual evidence that is counter to his preconceived world view and the more difficult it becomes for him to refute it without losing face the chance of him calling you a racist, bigot, homophobe approaches infinity. This is despite the thread you are in having not mentioned race or sexual preference in any way that is relevant to the subject." Grey Ghost |
All times are GMT +1. The time now is 09:53 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter