Gasket Cutter Photos
 

I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

Gasket Cutter Photos
 

Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

That's purdy, Pete.

--Winston

Gasket Cutter Photos
 

Thanks Pete - that looks handy!

Martin

Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

Gasket Cutter Photos
 

On Aug 4, 2:20*pm, Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. *It uses No. 11 X-acto
blades. *I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. *The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/Gask...etCutter02.JPG

Pete Keillor

Makin' the tools that fix the tools... thanks for the moment of non-
suck.


Dave

Gasket Cutter Photos
 

XR650L_Dave wrote:
On Aug 4, 2:20 pm, Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/Gask...etCutter02.JPG

Pete Keillor

Makin' the tools that fix the tools... thanks for the moment of non-
suck.

Ramen, brother.

--Winston

Gasket Cutter Photos
 

Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

WHAT?? No vernier adjustment on the blade protrusion ?? tsk tsk G

Gasket Cutter Photos
 

On Wed, 05 Aug 2009 17:24:10 GMT, the infamous Jerry Wass
scrawled the following:

Pete Keillor wrote:
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

WHAT?? No vernier adjustment on the blade protrusion ?? tsk tsk G

He'd likely have put on a micrometer action if he didn't use a micron
visual comparator. G

--
"It was difficult for the three of us to write a book titled _The End
of Prosperity_."

"We're not doom and gloom people; we're natural optimists. And we're not
part of the trendy set of intellectuals who like to trash our nation,
blame America first for all the world's problems, or worst of all,
predict with glee America's downfall as some kind of punishment for our
alleged past environmental crimes, racism, financial mismanagement, greed,
overconsumption, imperialism, or whatever the latest chic attack on the
United States is."
--page one, by Arthur B. Laffer, Stephen Moore, & Peter Tanous

Gasket Cutter Photos
 

"Pete Keillor" wrote in message
...
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

Nice looking tool. I am curious about something however, why did you choose
such a large chunk of iron to hold such a small blade? And would not a
tapered center point be much easier to spot correctly?

--

Roger Shoaf

About the time I had mastered getting the toothpaste back in the tube, then
they come up with this striped stuff.

Gasket Cutter Photos
 

On 2009-08-08, Roger Shoaf wrote:

"Pete Keillor" wrote in message
...
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

Nice looking tool. I am curious about something however, why did you choose
such a large chunk of iron to hold such a small blade?

My guess is that it prevents tipping of the blade carrier and
digging in.

And would not a
tapered center point be much easier to spot correctly?

I think that a small part of it is tapered, but again you are
benefiting from the large surface area of the holder preventing tipping
and gouging of the gasket material.

Enjoy,
DoN.

--
Email: | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---

Gasket Cutter Photos
 

On 8 Aug 2009 05:11:45 GMT, "DoN. Nichols"
wrote:

On 2009-08-08, Roger Shoaf wrote:

"Pete Keillor" wrote in message
...
I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor

Nice looking tool. I am curious about something however, why did you choose
such a large chunk of iron to hold such a small blade?

My guess is that it prevents tipping of the blade carrier and
digging in.

And would not a
tapered center point be much easier to spot correctly?

I think that a small part of it is tapered, but again you are
benefiting from the large surface area of the holder preventing tipping
and gouging of the gasket material.

Enjoy,
DoN.

That was my reasoning, DoN, which worked well in practice. To Roger's
point, I did find that on the second cut, relocating the center was a
pain. However, it was easily solved in about 1 second by picking up
the cut disc, setting it on the pivot with the cutter held upside
down, then flipping the whole thing back over on the cutting mat.

Other than the blade pin, the only other thing I might do is cut the
rod down to a reasonable length. 8" would probably be plenty for
anything I might encounter.

Pete Keillor

Gasket Cutter Photos
 

On Tue, 04 Aug 2009 14:20:47 -0400, Pete Keillor
wrote:

I made this little cutter to make the spindle gasket for my Hardinge
TM, which is finally going back together. It uses No. 11 X-acto
blades. I may add a dowel for the slot in the blade, but maybe not.
It worked fine on a cutter mat. The pivot is a hand ground point on a
set screw locked by a second set screw.

http://metalworking.com/dropbox/GasketCutter.txt
http://metalworking.com/dropbox/GasketCutter01.JPG
http://metalworking.com/dropbox/GasketCutter02.JPG

Pete Keillor


Oooo! Very nice. Print it and email me the drawings so I can build one
too!! Pretty Pretty Please!!!!

Gunner, Hardinge specialist.

'In the first place, we should insist that if the immigrant who comes here in good faith
becomes an American and assimilates himself to us, he shall be treated on an exact
equality with everyone else, for it is an outrage to discriminate against any such man
because of creed, or birthplace, or origin. But this is predicated upon the
person's becoming in every facet an American, and nothing but an American...
There can be no divided allegiance here. Any man who says he is an American,
but something else also, isn't an American at all. We have room for but one flag,
the American flag... We have room for but one language here, and that is the
English language.. and we have room for but one sole loyalty and that is a
loyalty to the American people.'
Theodore Ro osevelt 1907