1 Piece Die Holder for Lathe?
 

I just received a die holder to use on my mini-lathe tailstock. I was
surprised to find it was only 1 piece - sort of a "t" outline, with a
1" recess for the die at the big end and a hollow shaft at the other.
I was expecting something with 2 pieces that slid as the die cut the
threads. Am I missing a piece? Should I make an "arbour" to go into
the tailstock that the holder can slide on? Is this a die holder for
something other than a lathe tailstock?

Thanks,
Chris

1 Piece Die Holder for Lathe?
 

1 Piece Die Holder for Lathe?
 

On Fri, 06 Feb 2009 22:22:23 +0000, David Billington
wrote:

wrote:
I just received a die holder to use on my mini-lathe tailstock. I was
surprised to find it was only 1 piece - sort of a "t" outline, with a
1" recess for the die at the big end and a hollow shaft at the other.
I was expecting something with 2 pieces that slid as the die cut the
threads. Am I missing a piece? Should I make an "arbour" to go into
the tailstock that the holder can slide on? Is this a die holder for
something other than a lathe tailstock?

Thanks,
Chris

Chris,

From your description it does sound like you're missing the arbor that
fits in the tailstock and the die holder slides on. Have you contacted
the vendor for clarification of what should be there. Do you have a link
to the item you bought.
-----------
I think what he has is
http://www.use-enco.com/CGI/INSRIT?P...&PARTPG=INLMK3

The sliding type is like this
http://www.thewarfields.com/cnccookb...ilstockDie.htm
http://www.majosoft.com/metalworking...ie_holder.html
(I suggest a set screw below the surface to retain the die to
avoid injury when the holder spins.)
store bought
http://www.engineering-supplies.com/subcat.asp?id=242
http://www.axminster.co.uk/product-A...der-453621.htm
http://littlemachineshop.com/product...314&category=1
(domestic US source)

If you like the sliding type, you can make a sleeve with a 1/2
diameter hole to slide along the guide and then just clamp your
existing holder in one end of the sleeve. Not as "shoppy" as a
custom piece that you knurled, but a lot quicker.


Unka' George [George McDuffee]
-------------------------------------------
He that will not apply new remedies,
must expect new evils:
for Time is the greatest innovator: and
if Time, of course, alter things to the worse,
and wisdom and counsel shall not alter them to the better,
what shall be the end?

Francis Bacon (1561-1626), English philosopher, essayist, statesman.
Essays, "Of Innovations" (1597-1625).

1 Piece Die Holder for Lathe?
 

On Feb 6, 5:22*pm, David Billington
wrote:
snip
*From your description it does sound like you're missing the arbor that
fits in the tailstock and the die holder slides on. Have you contacted
the vendor for clarification of what should be there. Do you have a link
to the item you bought.

can't make a link for some reason. "http://www.kbctools.com/can/
main.cfm" gets close, then you need to go to page 129. It's KBC
part# 1-528-004.

I think I can make it work using the suggests made. I'll make an
arbour for it some time when I get a round tuit.

C.

1 Piece Die Holder for Lathe?
 

On Feb 6, 6:08*pm, F. George McDuffee gmcduf...@mcduffee-
associates.us wrote:
snip
Let the group know how you make out and any hints or tips you may
care to share.


Hey, this thing works pretty well! I was a bit concerned about the
tailstock clanking once it was loosened to slide easily, but it didn't
seem to affect the results too much. Might chuck the holder in the
headstock and skim the "socket" for the die - it looks like it might
be a bit uneven.

Don't know if I'd want to make any big threads, but it does a better
job on small stock (1/4") than I can by hand in the vise.

C.

1 Piece Die Holder for Lathe?