router with endmill on steel
 

Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts with coolant? How about a
1/4" spiral up carbide woodworking bit?

router with endmill on steel
 

In article . com,
mark wrote:

Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts with coolant? How about a
1/4" spiral up carbide woodworking bit?

You can route aluminum, but steel is hopeless.

Woodworking bits may be too light, unless we are talking about trimming
the edge of a piece of thin sheetmetal.

Coolant recommended for thicker stock, but what a mess it will make.
Bit spins at 10,000 rpm min, and will throw the coolant everywhere.

Coolant must not be flammable. Water-based coolant recommended. But
keep it out of the router motor and bearings.

This isn't sounding like a very good idea, even if you can make it kinda
work. What are you trying to make?

Joe Gwinn

router with endmill on steel
 

mark wrote:

Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts with coolant? How about a
1/4" spiral up carbide woodworking bit?

Forget steel. Even if you can get the speed down the chatter is going to
wipe out your carbide em.

The spiral up carbide sounds like it might work in aluminum but be prepared
to ruin it. If you are trying to get any sort of depth in aluminum, I
wouldn't try for an end mill diameter slot. Better to go with reduced
diameter so you won't be bouncing against both sides of slot.

This opinion is worth what you paid for it ;) Report back results.

Wes

router with endmill on steel
 

On Sep 1, 4:31 pm, mark wrote:
Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts with coolant? How about a
1/4" spiral up carbide woodworking bit?

Mark,
This is definitely an interesting concept!
I feel that what you are trying to achieve is to make an impression
onto an aluminium flat sheet?
Would it be a better idea to get the top (Thinner) sheet cut by laser,
and then layer this on top of a solid sheet of aluminium, thereby,
giving the effect of indenting the top sheet with the pattern you
require?
Just a thought.
Best regards,
Anthony.

router with endmill on steel
 

wrote in message
ups.com...
On Sep 1, 4:31 pm, mark
wrote:
Could you use a router at slow speed with a small
1/4" endmill on
steel or aluminum taking very light cuts with
coolant? How about a
1/4" spiral up carbide woodworking bit?

Mark,
This is definitely an interesting concept!
I feel that what you are trying to achieve is to make
an impression
onto an aluminium flat sheet?
Would it be a better idea to get the top (Thinner)
sheet cut by laser,
and then layer this on top of a solid sheet of
aluminium, thereby,
giving the effect of indenting the top sheet with the
pattern you
require?
Just a thought.
Best regards,
Anthony.

I have used my rotozip on aluminum. Hogged out some
mounting holes, 3/8 alum plate, so it fit my enco
sander table...the table would not fit to the sander,
holes where about 1/8 off.

Could have shipped it back to enco, but fix was fast
and easy...

xman

router with endmill on steel
 

"mark" wrote in message
ups.com...
Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts with coolant? How about a
1/4" spiral up carbide woodworking bit?


Sure...do you have a video camera?

router with endmill on steel
 

mark wrote:

Could you use a router at slow speed with a small 1/4" endmill on
steel or aluminum taking very light cuts Â*with coolant? How about a
1/4" spiral up carbide woodworking bit?

I have used a router on aluminium. But only to camfer edges. Works great
with woodworking carbide bits.
I wouldn't try it on steel.

If you intend to use it for engraving: Pay attention! The bits for handheld
routers do have a chip-limiter (right expression?) and you can't use normal
metalworking bits for that!


Nick
--
The lowcost-DRO:
http://www.yadro.de