Cutting a 4" disk out of 1" steel plate
 

I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Cutting a 4" disk out of 1" steel plate
 

Any other options or suggestions?

1) Call up metalmart and order two pieces of 4 inch round stock
one inch long. It might cost you 20 bucks but look at the pain
you are saving. I would also advise playing with the stock
dimesions before ordering. I just ordered some bar stock and
it didn't cost much more for 3 feet than 1 foot.

2) Find someone with a heavy duty bandsaw.

Cutting a 4" disk out of 1" steel plate
 

Jim,

Just use the best tool available, and consider the value of your time.

Myself I would bandsaw the disks on my vertical bandsaw. Your method
of "gas axe and grind" sounds doable if you can burn reasonably well.

As you say, sabre saw sounds painful.

Can you fit your gas axe to a crude circle cutting attachment
jury-rigged?

One other method would be to phone metal fabricators in your area and
check their price for disk burning from your material.

Also a scrap yard may have disks from boiler manufacturer's scrap pile.

As a final resort you could cut out the disks by drilling.........I
used to do this before I got my band saw and modified it for metal
cutting. I used 3/16 dia. drills because I had a lot of them.

Trust this is of some help.

Wolfgang

Cutting a 4" disk out of 1" steel plate
 

Lacking a torch myself and often times needing roundstock and only
having flat stock to make round out of, I resort to my rotary table
and make em.May be a bit time consuming in some cases. I have made a
heap of round items and disks form plate stock, and ifnish turn it on
a lathe.Works fine....Fire axe may be quicker, but like I said I do
not own one and I hate doing interuped cuts etc if I can help it.

I do have a metal cutting bandsaw which is what I rough out plate
stock on now, which certainly would be better than using a sabre saw
IMHO.


Doing it on a RT is not a bad job in all reality though.

On Wed, 18 Jan 2006 11:08:01 -0800, Jim Stewart
wrote:
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

--
\\\|///
( @ @ )
-----------oOOo(_)oOOo---------------


oooO
---------( )----Oooo----------------
\ ( ( )
\_) ) /
(_/
The original frugal ponder! Koi-ahoi mates....

Cutting a 4" disk out of 1" steel plate
 

use a cutting guide with your torch. best guide is one cut from 20 ga
steel, supported about 3/8" off the surface. A piece of 1/2" plywood
will do. Guide diameter is your rough out diameter minus the diameter of
the torch head. Clean up the worst of it with the grinder, chuck it in
the lathe. the first few passes aren't fun but it cleans up quickly.

I made a face plate and a chuck backing plate for my lathe out of 1"
stock this way. Takes more time to talk about it than just do it.

Jim Stewart wrote:
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Cutting a 4" disk out of 1" steel plate
 

I've had good luck drilling a series of holes and then going to the cold
chisel. John
"Jim Stewart" wrote in message
...
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Cutting a 4" disk out of 1" steel plate
 

Jim Stewart wrote:

I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Forget the saber saw. If it were me I'd certainly flame cut the plate.

This would be a good application for one of those Val-cut trepanning tools, just
bolt the plate to your mill table and trepan your 4" disks. If you really knew
what you were doing you could maybe grind a trepanning bit you could use in a
boring head.

GWE

Cutting a 4" disk out of 1" steel plate
 

"Jim Stewart" wrote in message
...
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?


Hole saw in a drill press, with a new saw it should take about 15 minutes
per disk. Been there done it.

Best Regards
Tom.

Cutting a 4" disk out of 1" steel plate
 

On Wed, 18 Jan 2006 11:08:01 -0800, Jim Stewart
wrote:

I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Circles out of plate is something I've done occasionally.
I use a shop made circle device on the head of the c-torch.
It's a modified cable clamp and some stock and rod. Center
drill, set the radius and go. If everything is adjusted perfect the
results are sweet. Finish on the lathe with a stub arbor.

DE


----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

Cutting a 4" disk out of 1" steel plate
 

In article oFCzf.14144$V.8590@fed1read04, "azotic"
wrote:



"Jim Stewart" wrote in message
...
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?


Hole saw in a drill press, with a new saw it should take about 15 minutes
per disk. Been there done it.

Flood with coolant all the while.

Joe Gwinn

Cutting a 4" disk out of 1" steel plate
 

azotic wrote:


"Jim Stewart" wrote in message
...
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?


Hole saw in a drill press, with a new saw it should take about 15 minutes
per disk. Been there done it.

Best Regards
Tom.



Second this method

Cutting a 4" disk out of 1" steel plate
 

"Jim Stewart" wrote in message
...
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Any other options or suggestions?

Find someone with a good PLASMA CUTTER.

It will change your life as you know it.

Cutting a 4" disk out of 1" steel plate
 

"Jim Stewart" wrote in message
...

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

Any other options or suggestions?

Gas axe, but center pop the middle of the disk, and attach a trammel point
to the torch, approx 2 1/8" from the edge of the center hole, at the right
height to keep the flame the correct distance off the steel. You _will_ be
amazed at how smooth you can cut, once you figure this out. Of course, right
sized, CLEAN tip, with correct cutting pressures for the steel indicated are
assumed. I can email a picture, if you don't know what I'm talking about.

Cutting a 4" disk out of 1" steel plate
 

azotic wrote:

Hole saw in a drill press, with a new saw it should take about 15 minutes
per disk. Been there done it.

I like the general idea, however I'm not sure just any drill press is
up to it. A friend and I did a 3 inch hole in 1" CRS this way in a
little rockwell knee mill, and found that even on the lowest speed it
was near stalling out - for 4 inches (or a bit over for finishing
allowance) I'd probably want a bridgeport with back gears. Or maybe
figure out some way to fixture the workpiece on the lathe carriage and
use the lathe to spin the hole saw.

We drilled some 1/2" holes around the circumference to help with
coolant flow and chip clearance.

I think we also had to flip the workpiece over half way through -
alignment was easy as there was a pilot hole (the slug was waste in our
case, we wanted the piece it was cut from)

Also, I wouldn't try to hold a hole saw of that size in a drill chuck.
In our case we were able to grab a larger diameter part of it with a
collet, rather than the narrow part meant to be chucked.

Cutting a 4" disk out of 1" steel plate
 

Jim,
Easy; Call McMaster Carr today, open package tomorrow. Machine
flywheels tomorrow night, move on to next part

Bob

Cutting a 4" disk out of 1" steel plate
 

I have read at least a dozen other posts on this subject.
Last Thursday our blacksmith club had its monthly meeting at a steel
supplier's shop in our area. Right by the saw were lots of rounds of
differing sizes, up to at least 6 inches diameter. I'd go with cutting
your parts out of round stock that way.
There were several posts about using a hole saw. When sawing out 1
9/16" diameter holes in 1 inch plate, which I do now and then, it takes
a fair amount of power and about 2 minutes per hole at (too fast at 350
rpm). A 4" hole means 12 1/2" of cutting contact or 4 times as much as
in my case. That's a lot!
I also did this hole cutting on a Bridgeport EZ Trak. I can take
1/4" deep cuts with a 1/2" corn cob end mill and it went pretty well.

Pete Stanaitis
---------------------------
Jim Stewart wrote:
I have a piece of CRS, about a foot square
and 1" thick. I want to cut out 2 disks about
4" in diameter. I will ultimately turn and
finish them into flywheels.

Given my tools, here are my options:

1. Rough out the disk with the gas axe,
grind away kerf with angle grinder,
turn on lathe.

2. Mount plate on rotary table, taking small
passes mill out disk, finish on lathe.

3. Try to cut out disk with sabre saw,
finish on lathe. Painful just thinking
about it...

Any other options or suggestions?

Cutting a 4" disk out of 1" steel plate
 

Hole saw in a drill press, with a new saw it should take about 15 minutes
per disk. Been there done it.

Flood with coolant all the while.


And drill a chip clearance hole (or several)
Geoff