R8 Taper Dimensions
 

I bought a cheap R8 collet for use in my neighbor's equally cheap
vertical mill. Surprise of the ages, it doesn't fit. I'm trying to
figure out whether the issue is collet or the mill. The problem seems
to be the groove depth. The tooling that came with the mill has a groove
that is 0.104" deep where as the collet has a groove 0.060" deep. The
collet groove is slightly wider, by less than half a thou.

What's correct? I Googled "R8 dimensions" (and standard, and drawing,
and every other combination I can think of) without luck. I'll RTFM if
I can find TFM.

Oz

--
Rich Osman, N1OZ
Rich Osman; POB 93167; Southlake, TX 76092 (Near DFW Airport)

R8 Taper Dimensions
 

I've had a similar problem with 5C collets from Enco. I was able to
mill the groove deeper on the worst ones but filing the pin slightly
shorter seemed the best fix.

jw
KB1DAL

R8 Taper Dimensions
 

The standard size for the groove should be 0.060- you will find that some
imported mills will have a key made for a deeper groove and in some cases a
wider groove as well.
"Rich Osman N1OZ" wrote in message
news:imJ7f.2956$I65.444@trnddc01...
I bought a cheap R8 collet for use in my neighbor's equally cheap
vertical mill. Surprise of the ages, it doesn't fit. I'm trying to
figure out whether the issue is collet or the mill. The problem seems
to be the groove depth. The tooling that came with the mill has a groove
that is 0.104" deep where as the collet has a groove 0.060" deep. The
collet groove is slightly wider, by less than half a thou.

What's correct? I Googled "R8 dimensions" (and standard, and drawing,
and every other combination I can think of) without luck. I'll RTFM if
I can find TFM.

Oz

--
Rich Osman, N1OZ
Rich Osman; POB 93167; Southlake, TX 76092 (Near DFW Airport)

R8 Taper Dimensions
 

http://www.oldengine.org/members/die.../Clarkson3.htm

R8 Taper Dimensions
 

The machinery's handbook has all the dimensions for nearely every taper
device ever made. You should be able to find it at your local library.

R8 Taper Dimensions
 

On 26 Oct 2005 07:44:48 -0700, "woodworker88"
wrote:

The machinery's handbook has all the dimensions for nearely every taper
device ever made. You should be able to find it at your local library.
XXXXXXXXXXXXXXXXXXXX
Hey woodworker88,

Yep, but R-8 is not shown under "Taper", but rather under "Collets".
And in my three MH books, only the basic info is given, and does not
include any reference to the key slots in any.

Take care.

Brian Lawson,
Bothwell, Ontario.

R8 Taper Dimensions
 

On Wed, 26 Oct 2005 13:01:21 GMT, "Chief McGee"
wrote:

http://www.oldengine.org/members/die.../Clarkson3.htm



Which shows it to be 5/32 wide, 3/32 deep, and 3" long.

Take care.

Brian Lawson,
Bothwell, Ontario.

R8 Taper Dimensions
 

Guys..as a machine tool repair tech..Ill put in my .02 worth. Its VERY
common for import collets to not fit American made machines, let alone
import machines. You get what you pay for.

Your two options a

Take your trusty Dremal tool (or equiv) and a small stone..and make
the slot a smidge wider and deeper, which takes all of about 2 minutes
per

Or thin/shorten your pin. Which takes about 30 minutes or longer.

Its not rocket science. And its strictly due to **** poor quality
control of imported (and occasionally domestic) tooling

Ive seen even (Barrummmm) Hardinge (Barruummmmm) collets be a bit
sticky because of a burr etc. Often times..cramming the slot into
the face of a spinning soft wheel will open the slot enough for it to
work thereafter.

**** happens. Deal with it and drive on.


Gunner, who is fasinated that a Very nice SB Heavy 10, well tooled,
with collet closer, didnt sell at the Visalia show, for $1000,
probably because the paint wasnt perfect and there were lots of tire
kickers looking for perfect machines for nearly free.
"Pax Americana is a philosophy. Hardly an empire.
Making sure other people play nice and dont kill each other (and us)
off in job lots is hardly empire building, particularly when you give
them self determination under "play nice" rules.

Think of it as having your older brother knock the **** out of you
for torturing the cat." Gunner

R8 Taper Dimensions
 

Sorry about that. I seem to remember looking up some information about
r-8 stuff before, although that was a diameter dimension if I remember
correctly.
I'll look more carefully in the future.

R8 Taper Dimensions
 

Seems to be a common problem with Shoptask 3in1. Common cure is to set
up a boring bar in your vice and lower the spindle of the mill onto it
while spinning.

cheers
T.Alan

Rich Osman N1OZ wrote:
I bought a cheap R8 collet for use in my neighbor's equally cheap
vertical mill. Surprise of the ages, it doesn't fit. I'm trying to
figure out whether the issue is collet or the mill. The problem seems
to be the groove depth. The tooling that came with the mill has a groove
that is 0.104" deep where as the collet has a groove 0.060" deep. The
collet groove is slightly wider, by less than half a thou.

What's correct? I Googled "R8 dimensions" (and standard, and drawing,
and every other combination I can think of) without luck. I'll RTFM if
I can find TFM.

Oz

R8 Taper Dimensions
 

According to EdFielder :
"Rich Osman N1OZ" wrote in message
news:imJ7f.2956$I65.444@trnddc01...
I bought a cheap R8 collet for use in my neighbor's equally cheap
vertical mill. Surprise of the ages, it doesn't fit. I'm trying to
figure out whether the issue is collet or the mill. The problem seems
to be the groove depth. The tooling that came with the mill has a groove
that is 0.104" deep where as the collet has a groove 0.060" deep. The
collet groove is slightly wider, by less than half a thou.

What's correct? I Googled "R8 dimensions" (and standard, and drawing,
and every other combination I can think of) without luck. I'll RTFM if
I can find TFM.

The standard size for the groove should be 0.060- you will find that some
imported mills will have a key made for a deeper groove and in some cases a
wider groove as well.

Note that at least on a Bridgeport, the key is the end of a
dog-point Allen screw (which can be accessed through a hole in the back
of the quill). You'll probably have to rotate the spindle until the
screw lines up with the access hole.

There are actually *two* Allen screws in the hole. From what I
have read, it is often the case that the outer one (which serves to lock
the inner one with the dog point at a proper level) is one with the hex
hole all the way through. So -- you loosen the outer one, pass the
Allen key in to access and adjust the inner one, set the depth correctly
for that worst-case collet, then back the Allen key out so it is only
engaging the lock screw, and tighten that to hold the lock screw at the
proper depth. Then -- make sure that the one with the dog point has not
moved, so you can get that worst-case collet in and out without
problems.

I don't know that the mill which your neighbor owns has the same
system, but it may be worth checking for that, so you can adjust it (if
he so allows).

This is also good to know about so you can replace the dog point
screw if the key happens to get sheared off by a mishap at some time in
the future.

Good Luck,
DoN.
--
Email: | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---

R8 Taper Dimensions
 

The Shoptask machines use a Morse taper #3 spindle- maybe you are thinking
of Smithy which has R-8 models.

"T.Alan Kraus" wrote in message
...
Seems to be a common problem with Shoptask 3in1. Common cure is to set
up a boring bar in your vice and lower the spindle of the mill onto it
while spinning.

cheers
T.Alan

Rich Osman N1OZ wrote:
I bought a cheap R8 collet for use in my neighbor's equally cheap
vertical mill. Surprise of the ages, it doesn't fit. I'm trying to
figure out whether the issue is collet or the mill. The problem seems
to be the groove depth. The tooling that came with the mill has a groove
that is 0.104" deep where as the collet has a groove 0.060" deep. The
collet groove is slightly wider, by less than half a thou.

What's correct? I Googled "R8 dimensions" (and standard, and drawing,
and every other combination I can think of) without luck. I'll RTFM if
I can find TFM.

Oz

R8 Taper Dimensions (try Deux)
 

Gunner wrote:
Guys..as a machine tool repair tech..Ill put in my .02 worth. Its VERY
common for import collets to not fit American made machines, let alone
import machines. You get what you pay for.

Your two options a

Take your trusty Dremal tool (or equiv) and a small stone..and make
the slot a smidge wider and deeper, which takes all of about 2 minutes
per

Or thin/shorten your pin. Which takes about 30 minutes or longer.

Its not rocket science. And its strictly due to **** poor quality
control of imported (and occasionally domestic) tooling

Yup, understand and agree with all of this. That's why I got a $6
collet rather than a $60 one to use with this $400 Rong Wei mill. What
I'm wondering though is which (or both) is out of spec, and by how much.
If it's the mill, I'll correct it so I have fewer future problems.

Back to the original question. Does anyone know how I find the specs on
an R-8 shaft, specifically the index groove?

Oz

R8 Taper Dimensions (try Deux)
 

The 3/4' collet for Segway's Bridgeport measures 0.160 wide by 0.063
deep. (I'll take any excuse to zip around the factory, which is laid
out like a race track.)

jw, who seems to have become the toymaker here. Not sure if that means
elf or troll.

R8 Taper Dimensions (try Deux)