Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Why Delta decalred bankruptcy
|
#2
|
|||
|
|||
Cheasy Photoshop fake.
JR Dweller in the cellar Rex B wrote: http://priceless420.com/Pr091705stuck.jpg -- -------------------------------------------------------------- Home Page: http://www.seanet.com/~jasonrnorth If you're not the lead dog, the view never changes Doubt yourself, and the real world will eat you alive The world doesn't revolve around you, it revolves around me No skeletons in the closet; just decomposing corpses -------------------------------------------------------------- Dependence is Vulnerability: -------------------------------------------------------------- "Open the Pod Bay Doors please, Hal" "I'm sorry, Dave, I'm afraid I can't do that.." |
#3
|
|||
|
|||
JR North wrote:
Cheasy Photoshop fake. Deja Vu all over again. http://www.cargolaw.com/1999nightmare.html Kevin Gallimore ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
#4
|
|||
|
|||
axolotl wrote:
JR North wrote: Cheasy Photoshop fake. Deja Vu all over again. http://www.cargolaw.com/1999nightmare.html Kevin Gallimore Awesome site! Ken. |
#5
|
|||
|
|||
In article , JR North says...
Cheasy Photoshop fake. Apparently not. It was not sucked in, but rather blown in by another aircraft on the ramp. It was at gatwick I think. Jim -- ================================================== please reply to: JRR(zero) at pkmfgvm4 (dot) vnet (dot) ibm (dot) com ================================================== |
#6
|
|||
|
|||
It is not a fake, it really did happen.
Searcher1 |
#7
|
|||
|
|||
--Had me worried when I thot immediately of the tool company;
screw the airline! ;-) -- "Steamboat Ed" Haas : Post Burn thought for the day: Hacking the Trailing Edge! : Why wear pants? http://www.nmpproducts.com/intro.htm ---Decks a-wash in a sea of words--- |
#8
|
|||
|
|||
Hmmm. The CG is all wrong for it to be stable in the intake duct. The
left rear upper corner of the container, which would need to be inside the duct, and so restrain the container from rotating out, is actually outside. It would have to be VERY firmly wedged at the other contact points, but I don't see any distortion in the duct wall at the contact point on the left. At the angle the container rests, the right upper corner is inside the duct, but the container walls slope outwards in relation to the duct, so that corner would not prevent the container from rotating down on the other two pivot points. JR Dweller in the cellar jim rozen wrote: In article , JR North says... Cheasy Photoshop fake. Apparently not. It was not sucked in, but rather blown in by another aircraft on the ramp. It was at gatwick I think. Jim -- -------------------------------------------------------------- Home Page: http://www.seanet.com/~jasonrnorth If you're not the lead dog, the view never changes Doubt yourself, and the real world will eat you alive The world doesn't revolve around you, it revolves around me No skeletons in the closet; just decomposing corpses -------------------------------------------------------------- Dependence is Vulnerability: -------------------------------------------------------------- "Open the Pod Bay Doors please, Hal" "I'm sorry, Dave, I'm afraid I can't do that.." |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Katrina and the Reality of Bankruptcy | Metalworking | |||
FS Delta 36-600 / Gloat New TS | Woodworking | |||
Grizz G1182HW vs. Delta 37-195 jointer... | Woodworking | |||
Delta Announcement | Woodworking | |||
My New Delta Saw | Woodworking |