Roof ridge vent: a DIY project?
 

I am a fairly competent DIYer. Need to install ridge vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.

Thanks!
Todd in Cincy

Roof ridge vent: a DIY project?
 

Todd W. Roat wrote:
I am a fairly competent DIYer. Need to install ridge vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.

Thanks!
Todd in Cincy

A few years ago I hired a roofer to pull two layers of shingles,
check the plywood underlayment holding up the shingles, and
install a ridge vent and a fresh set of shingles.

Part of the ridge vent installation procedure is to cut a slit
one or two inches wide in the roof underlayment to let the air
through. My lack of talent for free hand sawing of a straight
line forty feet long made me glad I was not on the roof making
the cut.

Roof ridge vent: a DIY project?
 

I think that John has mixed up "ridge vent" and "sofit vent". The ridge
vent goes on the front and back of the house just below the peak of the
roof. The "sofit vent" or vents go on the sofit, the underside of the roof
edge. I'm afraid that I can't give you much advice in this area either Todd
and I am paying to have someone do this as well. Hope you get a response
from someone who can give you the requested feedback.

-G

"JohnB" wrote in message
ink.net...
Todd W. Roat wrote:
I am a fairly competent DIYer. Need to install ridge vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.

Thanks!
Todd in Cincy

A few years ago I hired a roofer to pull two layers of shingles,
check the plywood underlayment holding up the shingles, and
install a ridge vent and a fresh set of shingles.

Part of the ridge vent installation procedure is to cut a slit
one or two inches wide in the roof underlayment to let the air
through. My lack of talent for free hand sawing of a straight
line forty feet long made me glad I was not on the roof making
the cut.

Roof ridge vent: a DIY project?
 

In alt.home.repair
"George Fairbairn" wrote:

I think that John has mixed up "ridge vent" and "sofit vent". The ridge
vent goes on the front and back of the house just below the peak of the
roof. The "sofit vent" or vents go on the sofit, the underside of the roof
edge. I'm afraid that I can't give you much advice in this area either Todd
and I am paying to have someone do this as well. Hope you get a response
from someone who can give you the requested feedback.

No, a ridge vent does exactly what it says, runs on the ridge. I think he
would have no trouble installing one. Pop a couple of chalk lines to saw
by. Use a circular saw with a cheap blade and rip the lines. Tear up the
waste leaving the gap. Install the ridge per the manf recommendations and
cap with shingle tabs. Nothing to it.

Roof ridge vent: a DIY project?
 

Todd wrote: I am a fairly competent DIYer. Need to install ridge
vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.


Sure, no problem. As long as your roof pitch is safely walkable, climb on up
there and carefully remove all the existing ridge caps where you'll want the
vent. Save 'em. Now snap a chalk line along both sides of the ridge about 2
inches down. Get a "roofers blade" on your circ saw, 'cause you'll be cutting
through some metal, and set the depth just a quarter to a half inch deeper than
the depth of the plywood substrate. Test cut a bit and measure the resultant
opening. Adjust chalkline as needed, and cut the entire ridge just up to the
rakeboards, even if it'll only ventilate to the overhang, and it'll look much
straighter, not upswept or dropped at the ends. Install a couple new caps at
the rake end(s). Apply the ridge venting to the entire ridge, something with a
bug-barrier fabric preferred, with some fasteners that'll _just_ hold it down
while you're installing the ridge caps with the provided two-inch or so roofing
nails. Tom
Someday, it'll all be over....

Roof ridge vent: a DIY project?
 

On 1 Jun 2004 06:41:21 -0700, (Todd W. Roat) wrote:

I am a fairly competent DIYer. Need to install ridge vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.

Thanks!
Todd in Cincy

I did my ridge vent last year and can give you a little advice that
is fresh in my mind.

1. Don't make the slits wider than necessary. Follow the
instructions that come with your ridge vents exactly. (I wanted to
make them wider - big mistake).

2. I bought a new saw blade and wore it completely out on the first 12
inches I cut. It lasted less than 20 seconds. ( Don't try to saw thru
gravel coated shingles. Cut them with a knife.)

3. I have a hip roof so I didn't have enough 'ridge' area so I had to
run the ridge vent down the hips half way. You are only going to
tackle that job only once so don't be stingy with the ridge vent.
They sell special ridge vent for hips.

The job is easy enough for the homeowner but it takes longer than you
might think. Have some emergency covering for the event of rain.

Les

Roof ridge vent: a DIY project?
 

Thanks for all the input. Think I will give it a try. Determined to
use my circ saw as opposed to kniwfe for time sake - will try a
carbide roofer blade. Now it seems I have to pick a roof vent - seems
there a trillion brands. Consensus is to use the baffled vent ones
that conduct airflow out better and keep weather out.

(Todd W. Roat) wrote in message . com...
I am a fairly competent DIYer. Need to install ridge vents. Could I
screw this up? Seems simple enough. Was hoping someone with
experience could teel me:

1) Most common mistake, things to watch out for.
2) best kind of vent to install.

Thanks!
Todd in Cincy