DIYbanter

DIYbanter (https://www.diybanter.com/)
-   Home Repair (https://www.diybanter.com/home-repair/)
-   -   Construction Adhesive Nightmare (https://www.diybanter.com/home-repair/581492-construction-adhesive-nightmare.html)

Meanie[_6_] November 16th 16 02:50 AM

Construction Adhesive Nightmare
 
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?

[email protected] November 16th 16 03:29 AM

Construction Adhesive Nightmare
 
On Tue, 15 Nov 2016 21:50:09 -0500, Meanie wrote:

Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?


Just because you're a Stud, whatever you do, DONT put construction
adhesive on your dick before having sex, unless you really love your sex
partner. You might be attached forever.

As for removal on the WOODEN studs. A heat gun might help. Be careful,
they can start fires. Keep a bucket of water nearby.

You could have just put the sheetrock right over the paneling!


Bill Gill November 16th 16 02:12 PM

Construction Adhesive Nightmare
 
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?

Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill


trader_4 November 16th 16 02:49 PM

Construction Adhesive Nightmare
 
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?

Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill


One solution might be to just put the new drywall over the paneling?

DerbyDad03 November 16th 16 05:57 PM

Construction Adhesive Nightmare
 
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?

Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill


One solution might be to just put the new drywall over the paneling?


I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

Colonel Edmund J. Burke[_16_] November 16th 16 06:02 PM

Construction Adhesive Nightmare
 
On 11/16/2016 6:12 AM, Bill Gill wrote:

Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.


I use it wherever the **** I please.


Meanie[_6_] November 16th 16 07:38 PM

Construction Adhesive Nightmare
 
On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill


One solution might be to just put the new drywall over the paneling?


I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.

Stormin' Norman November 16th 16 07:49 PM

Construction Adhesive Nightmare
 
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:

On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill

One solution might be to just put the new drywall over the paneling?


I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


How are you removing the excess CA? I had to remove several very large mirrors that were glued to a wall and
then had to remove the excess adhesive from the back of the mirrors. It is not the same as standard CA, I
used a thick, long handled curved scraper and I heated the blade over a torch. The heated blade made the
adhesive removal much easier, but it was still a pain in the ass.

[email protected] November 16th 16 07:55 PM

Construction Adhesive Nightmare
 
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:


One solution might be to just put the new drywall over the paneling?


I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


What is *NOT RIGHT* about putting it over the paneling? You wont see the
paneling, and the paneling is just a tad bit more "insulation"....

Of course its too late now, unless you have other 'complete' walls to
do.


Meanie[_6_] November 16th 16 08:38 PM

Construction Adhesive Nightmare
 
On 11/16/2016 2:49 PM, Stormin' Norman wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:

On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill

One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


How are you removing the excess CA? I had to remove several very large mirrors that were glued to a wall and
then had to remove the excess adhesive from the back of the mirrors. It is not the same as standard CA, I
used a thick, long handled curved scraper and I heated the blade over a torch. The heated blade made the
adhesive removal much easier, but it was still a pain in the ass.


Scraper and hammer.

Meanie[_6_] November 16th 16 08:42 PM

Construction Adhesive Nightmare
 
On 11/16/2016 2:55 PM, wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:


One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


What is *NOT RIGHT* about putting it over the paneling? You wont see the
paneling, and the paneling is just a tad bit more "insulation"....

Of course its too late now, unless you have other 'complete' walls to
do.


Not right is putting it over paneling. I consider the right way with
bare studs. Also, my basement flooded a while ago and I wanted to ensure
there wasn't any mold within the current structure and insulation behind
it. I'm glad I did because I found some mold on one wall.

Stormin' Norman November 16th 16 08:44 PM

Construction Adhesive Nightmare
 
On Wed, 16 Nov 2016 15:38:11 -0500, Meanie wrote:

On 11/16/2016 2:49 PM, Stormin' Norman wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:

On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails for panel?

I'm removing old paneling in my basement and replacing with drywall. I
reach an area of the base where the past owners used CA along with panel
nails and it's a MFing nightmare to remove. I have to use a scraper and
hammer to pry it away from the stud. I can't think of any easy way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill

One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


How are you removing the excess CA? I had to remove several very large mirrors that were glued to a wall and
then had to remove the excess adhesive from the back of the mirrors. It is not the same as standard CA, I
used a thick, long handled curved scraper and I heated the blade over a torch. The heated blade made the
adhesive removal much easier, but it was still a pain in the ass.


Scraper and hammer.


I wonder if it might be easier to cut out and replace the worst of the studs? Better you than me.......

Bill Gill November 17th 16 02:10 PM

Construction Adhesive Nightmare
 
On 11/16/2016 2:38 PM, Meanie wrote:
On 11/16/2016 2:49 PM, Stormin' Norman wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:

On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails
for panel?

I'm removing old paneling in my basement and replacing with
drywall. I
reach an area of the base where the past owners used CA along
with panel
nails and it's a MFing nightmare to remove. I have to use a
scraper and
hammer to pry it away from the stud. I can't think of any easy
way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill

One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


How are you removing the excess CA? I had to remove several very
large mirrors that were glued to a wall and
then had to remove the excess adhesive from the back of the mirrors.
It is not the same as standard CA, I
used a thick, long handled curved scraper and I heated the blade over
a torch. The heated blade made the
adhesive removal much easier, but it was still a pain in the ass.


Scraper and hammer.

Have you thought of using one of those vibrating saws?
I don't know what the generic name is, but they are widely
available. The blade vibrates at a high speed and cuts through
stuff really well. Doctors use something like them for cutting
casts and bones and what have you. I have one from Harbor Freight
that does great. You can get scraper blades that may do the job.

Bill


Stormin' Norman November 17th 16 02:21 PM

Construction Adhesive Nightmare
 
On Thu, 17 Nov 2016 08:10:47 -0600, Bill Gill wrote:

On 11/16/2016 2:38 PM, Meanie wrote:
On 11/16/2016 2:49 PM, Stormin' Norman wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:

On 11/16/2016 12:57 PM, DerbyDad03 wrote:
On Wednesday, November 16, 2016 at 9:49:37 AM UTC-5, trader_4 wrote:
On Wednesday, November 16, 2016 at 9:12:01 AM UTC-5, Bill Gill wrote:
On 11/15/2016 8:50 PM, Meanie wrote:
Why in the hell would anyone use construction adhesive and nails
for panel?

I'm removing old paneling in my basement and replacing with
drywall. I
reach an area of the base where the past owners used CA along
with panel
nails and it's a MFing nightmare to remove. I have to use a
scraper and
hammer to pry it away from the stud. I can't think of any easy
way to
remove it without scraping.

Anyone ever experience a similar issue?
Construction adhesive is normally used when installing
paneling over sheet rock. I don't know about over
studs, but I expect that even if you don't need it a lot of
people would just go along with the standard procedure.

Bill

One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.

How are you removing the excess CA? I had to remove several very
large mirrors that were glued to a wall and
then had to remove the excess adhesive from the back of the mirrors.
It is not the same as standard CA, I
used a thick, long handled curved scraper and I heated the blade over
a torch. The heated blade made the
adhesive removal much easier, but it was still a pain in the ass.


Scraper and hammer.

Have you thought of using one of those vibrating saws?
I don't know what the generic name is, but they are widely
available. The blade vibrates at a high speed and cuts through
stuff really well. Doctors use something like them for cutting
casts and bones and what have you. I have one from Harbor Freight
that does great. You can get scraper blades that may do the job.

Bill


Funny, I was thinking the same exact thing yesterday, then I remembered I tried to use my HF oscillating
multi-tool to remove mirror adhesive and it was less than effective.

The oscillating tools are really great, except for how quickly I wear out the blades. The tool allows me to
do things in minutes that previously would have taken hours.

trader_4 November 17th 16 03:16 PM

Construction Adhesive Nightmare
 
On Wednesday, November 16, 2016 at 2:56:33 PM UTC-5, wrote:
On Wed, 16 Nov 2016 14:38:12 -0500, Meanie wrote:


One solution might be to just put the new drywall over the paneling?

I'm guessing it's too late now. I'll bet that he has created an uneven
surface by removing the paneling that came off easily and has already
begun to hack away at the remainder.

I don't blame him, he probably had no way of knowing about the CA until
he got started.

BINGO! Too far into it to reconsider over panel. Besides, I hate a half
ass job and prefer to do it the right way.


What is *NOT RIGHT* about putting it over the paneling? You wont see the
paneling, and the paneling is just a tad bit more "insulation"....


+1
It's every bit as good without the headache. If it were me and I had
only started to pull it off and found this out, I would have replaced
the panel on that section, then gone over it and the rest.



Of course its too late now, unless you have other 'complete' walls to
do.


+1


All times are GMT +1. The time now is 03:18 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter