Crown molding on a cathedral ceiling
 

Looks like I'm going to be using 5" crown molding on a cathedral
bedroom ceiling. It's paint-grade, but because the molding
profile is so large I will not be able to fake the joints.

The problems a

o Where the level ceiling line meets the rake, the plumb cut
on the rake molding will not match the profile on the level;
it will be wider. I was thinking of some sort of stop block
in the corner, but this doesn't seem ideal, or easy.

o The ceiling on the level runs moves up and away from the top
of the molding, creating a gap. I could place a filler strip
in
it, but that wouldn't match the rake profile. This also mitigates
for the use of stop blocks in the corners.

Any creative ideas would be appreciated.

p.

Crown molding on a cathedral ceiling
 

On Thu, 11 Dec 2003 16:08:34 -0500, "pb"
wrote:

Looks like I'm going to be using 5" crown molding on a cathedral
bedroom ceiling. It's paint-grade, but because the molding
profile is so large I will not be able to fake the joints.

The problems a

o Where the level ceiling line meets the rake, the plumb cut
on the rake molding will not match the profile on the level;
it will be wider. I was thinking of some sort of stop block
in the corner, but this doesn't seem ideal, or easy.

o The ceiling on the level runs moves up and away from the top
of the molding, creating a gap. I could place a filler strip
in
it, but that wouldn't match the rake profile. This also mitigates
for the use of stop blocks in the corners.

Any creative ideas would be appreciated.

p.


I've done lots of crown. Difficult to describe without seeing your
situation. Take a look at the base molding. Make returns to the wall
or run the molding straight into the wall, whichever looks better. (I
don't want to create a fight here, but...) I've found that women have
a knack knowing what looks best.

Crown molding on a cathedral ceiling
 

Phisherman wrote:

Make returns to the wall
or run the molding straight into the wall, whichever looks better.

Problem is, we don't want to terminate the crown when it meets
the rake wall, we want it to turn and climb up the slope.

p.

Crown molding on a cathedral ceiling
 

"pb" wrote in message
Phisherman wrote:

Make returns to the wall
or run the molding straight into the wall, whichever looks better.

Problem is, we don't want to terminate the crown when it meets
the rake wall, we want it to turn and climb up the slope.

p.

Your filler has to go on the wall not the ceiling, then when you run the
rake, the profile will match on your plumb cut. You already know you're
trying to use a crown made for a 90 degree angle to try to use for something
other than 90. Not a lot of choices without filler on the wall or having
custom crown made for the degree your cathedral slopes.

Crown molding on a cathedral ceiling
 

"pb" wrote in message
...
Looks like I'm going to be using 5" crown molding on a cathedral
bedroom ceiling. It's paint-grade, but because the molding
profile is so large I will not be able to fake the joints.

The problems a

o Where the level ceiling line meets the rake, the plumb cut
on the rake molding will not match the profile on the level;
it will be wider. I was thinking of some sort of stop block
in the corner, but this doesn't seem ideal, or easy.

o The ceiling on the level runs moves up and away from the top
of the molding, creating a gap. I could place a filler strip
in
it, but that wouldn't match the rake profile. This also mitigates
for the use of stop blocks in the corners.

Any creative ideas would be appreciated.

p.


use a bevel square to determine the angle then divide it in half.
cut each molding with that angle.
perfect fit every time (maybe a little caulk).

Crown molding on a cathedral ceiling
 

bogden wrote:

Your filler has to go on the wall not the ceiling, then when you run the
rake, the profile will match on your plumb cut. You already know you're
trying to use a crown made for a 90 degree angle to try to use for something
other than 90. Not a lot of choices without filler on the wall or having
custom crown made for the degree your cathedral slopes.

I take it you mean canting the level run upward, so the rake sees
it at a right angle. Interesting, I hadn't thought of that. But
even with the relatively low pitch roof - 3½ on 12 - I don't see
that looking good, on first consideration. Have you ever done
this, and how did it turn out?

The custom rake crown is the ideal solution, but it's not going
to happen.

p.

Crown molding on a cathedral ceiling
 

"pb" wrote in message
bogden wrote:

Your filler has to go on the wall not the ceiling, then when you run the
rake, the profile will match on your plumb cut. You already know you're
trying to use a crown made for a 90 degree angle to try to use for
something
other than 90. Not a lot of choices without filler on the wall or
having
custom crown made for the degree your cathedral slopes.

I take it you mean canting the level run upward, so the rake sees
it at a right angle. Interesting, I hadn't thought of that. But
even with the relatively low pitch roof - 3½ on 12 - I don't see
that looking good, on first consideration. Have you ever done
this, and how did it turn out?

The custom rake crown is the ideal solution, but it's not going
to happen.

p.

We've done something like it. It was a double oak build out (3 pc. crown).
The wall build out was thicker than the ceiling, so it really didn't show as
such. It showed as a 3 piece. We had ripped down the ceiling, to whatever
was needed, but ripped the thickness on both oak bands. Didn't try to get
it all on the one band.

Crown molding on a cathedral ceiling
 

bogden wrote:

You already know you're
trying to use a crown made for a 90 degree angle to try to use for something
other than 90

Your word picture has perhaps pointed out what I think is a
solution. Place the level piece first, relieving the top so it
fits to the ceiling, and mitering the end normally. Now make a
transition piece, mitered to the level piece and splay-mitered to
the coming rake piece.

Gonna be challenging to cut that transition piece, though.

That should work, and be geometrically correct, for inside
miters. The problem I still have is on a closet that comes off of
one level run. It's side follows the roof slope, but it's face is
level. The outside miter between the two would not seem to bow to
the above approach.

p.

Crown molding on a cathedral ceiling
 

How about a picture?
PJ


On Thu, 11 Dec 2003 21:47:12 -0500, "3GCPO" wrote:


"pb" wrote in message
.. .
Looks like I'm going to be using 5" crown molding on a cathedral
bedroom ceiling. It's paint-grade, but because the molding
profile is so large I will not be able to fake the joints.

The problems a

o Where the level ceiling line meets the rake, the plumb cut
on the rake molding will not match the profile on the level;
it will be wider. I was thinking of some sort of stop block
in the corner, but this doesn't seem ideal, or easy.

o The ceiling on the level runs moves up and away from the top
of the molding, creating a gap. I could place a filler strip
in
it, but that wouldn't match the rake profile. This also mitigates
for the use of stop blocks in the corners.

Any creative ideas would be appreciated.

p.


use a bevel square to determine the angle then divide it in half.
cut each molding with that angle.
perfect fit every time (maybe a little caulk).

Crown molding on a cathedral ceiling
 

Installing crown molding on a sloped ceiling is no more difficult than
installing the crown on a horizontal ceiling. For a sloped ceiling all
you are adding to the job are turns of the crown in a vertical direction.
In other words, when installing the horizontal crown and you get to a
corner where you want to turn upwards you make both a horizontal turn and
a vertical turn in the corner and then proceed up the sloped ceiling.
Visit us on line at www.compoundmiter.com for the tools and information
that will make your crown molding job fun and exciting and most of all
easy. Crown Molding & Trim: Install It Like A PRO! Free 0n-line tech
support. Questions call toll free 866-544-2016

Do-It-Yourself Crown Molding & Trim: Install It Like A PRO!

Sincerely yours
Wayne Drake, President
CompoundMiter, Inc.